Investigation of MO Adsorption Kinetics and Photocatalytic Degradation Utilizing Hollow Fibers of Cu-CuO/TiO Nanocomposite.

This comprehensive study explores the kinetics of adsorption and its photocatalytic degradation of methyl orange (MO) using an advanced copper-decorated photocatalyst in the form of hollow fibers (HFs). Designed to boost both adsorption capacity and photocatalytic activity, the photocatalyst was tested in batch experiments to efficiently remove MO from aqueous solutions. Various isotherm models, including Langmuir, Freundlich, Sips, Temkin, and Dubinin-Radushkevich, along with kinetic models like pseudo-first and pseudo-second order, Elovich, Bangham, and Weber-Morris, were utilized to assess adsorption capacity and kinetics at varying initial concentrations.

Mo-BiVO Photocatalytically Modified Ceramic Ultrafiltration Membranes for Enhanced Water Treatment Efficiency.

This study highlights the effectiveness of photocatalytically modified ceramic ultrafiltration (UF) membranes in alleviating two major drawbacks of membrane filtration technologies. These are the generation of a highly concentrated retentate effluent as a waste stream and the gradual degradation of the water flux through the membrane due to the accumulation of organic pollutants on its surface. The development of two types of novel tubular membranes, featuring photocatalytic Mo-BiVO inverse opal coatings, demonstrated a negligible impact on water permeance, ensuring consistent filtration and photocatalytic efficiency and suggesting the potential for maintaining membrane integrity and avoiding the formation of highly concentrated retentate effluents.

Formation of Polyimide Membranes via Non-Solvent Induced Phase Separation: Insight from Molecular Dynamics Simulations.

Molecular dynamics simulations were applied to investigate the formation of P84 polyimide membranes through the non-solvent induced phase separation (NIPS) process, considering two scenarios: one using a conventional organic solvent like n-methyl-2-pyrrolidone (NMP) and the other a greener alternative, γ-butyrolactone (GBL), with water serving as the non-solvent. Different compositions of polymer solutions were established along the binodal boundaries of the respective systems, derived from experimental cloud point data on the ternary phase diagram. The resulting polymer membranes were analyzed and compared in terms of their morphology.

Rapid hollow fiber-coating device for thin film composite membrane preparation.

Aligned with the recent trend and imperative to reduce separation layer thickness in gas separation membranes to the nanometer scale in order to raise permeance to levels that can render them competitive with respect to other gas separation technologies, a novel approach and device for fabricating defect-free composite hollow fiber (HF) membranes by dip-coating is described. The presented method avoids the fundamental drawbacks of state-of-the-art techniques for applying a thin gas separation layer onto a porous HF substrate, providing a safe but, at the same time, easily up-scalable way of producing HF membranes at a relatively high production rate. As a basic concept, hanging HF substrates are coated by allowing the coating solution to flow and drip along their external surface.

Utilizing Carbonaceous Materials Derived from [BMIM][TCM] Ionic Liquid Precursor: Dual Role as Catalysts for Oxygen Reduction Reaction and Adsorbents for Aromatics and CO.

This work presents the synthesis of N-doped nanoporous carbon materials using the Ionic Liquid (IL) 1-butyl-3-methylimidazolium tricyanomethanide [BMIM][TCM] as a fluidic carbon precursor, employing two carbonization pathways: templated precursor and pyrolysis/activation. Operando monitoring of mass loss during pyrolytic and activation treatments provides insights into chemical processes, including IL decomposition, polycondensation reactions and pore formation. Comparatively low mass reduction rates were observed at all stages.

A Combined Gas and Water Permeances Method for Revealing the Deposition Morphology of GO Grafting on Ceramic Membranes.

The adhesion enhancement of a graphene oxide (GO) layer on porous ceramic substrates is a crucial step towards developing a high-performance membrane for many applications. In this work, we have achieved the chemical anchoring of GO layers on custom-made macroporous disks, fabricated in the lab by pressing α-AlO powder. To this end, three different linkers, polydopamine (PDA), 3-Glycidoxypropyltrimethoxysilane (GPTMS) and (3-Aminopropyl) triethoxysilane (APTMS), were elaborated for their capacity to tightly bind the GO laminate on the ceramic membrane surface.

Novel 3D-Printed Biocarriers from Aluminosilicate Materials.

The addition of biocarriers can improve biological processes in bioreactors, since their surface allows for the immobilization, attachment, protection, and growth of microorganisms. In addition, the development of a biofilm layer allows for the colonization of microorganisms in the biocarriers. The structure, composition, and roughness of the biocarriers' surface are crucial factors that affect the development of the biofilm.

Comparative Study of the U(VI) Adsorption by Hybrid Silica-Hyperbranched Poly(ethylene imine) Nanoparticles and Xerogels.

Two different silica conformations (xerogels and nanoparticles), both formed by the mediation of dendritic poly (ethylene imine), were tested at low pHs for problematic uranyl cation sorption. The effect of crucial factors, i.e.

Nanocarbon-Based Mixed Matrix Pebax-1657 Flat Sheet Membranes for CO/CH Separation.

In the present work, Pebax-1657, a commercial multiblock copolymer (poly(ether-block-amide)), consisting of 40% rigid amide (PA6) groups and 60% flexible ether (PEO) linkages, was selected as the base polymer for preparing dense flat sheet mixed matrix membranes (MMMs) using the solution casting method. Carbon nanofillers, specifically, raw and treated (plasma and oxidized) multi-walled carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) were incorporated into the polymeric matrix in order to improve the gas-separation performance and polymer's structural properties. The developed membranes were characterized by means of SEM and FTIR, and their mechanical properties were also evaluated.

Novel Pilot-Scale Photocatalytic Nanofiltration Reactor for Agricultural Wastewater Treatment.

Nowadays, the increased agro-industrial activities and the inability of traditional wastewater treatment plants (WWTPs) to eliminate recalcitrant organic contaminants are raising a potential worldwide risk for the environment. Among the various advanced water treatment technologies that are lately proposed for addressing this challenge, the development and optimization of an innovative hybrid photocatalytic nanofiltration reactor (PNFR) prototype emerges as a prominent solution that achieves synergistic beneficial effects between the photocatalytic degradation activity and size exclusion capacity for micropollutant molecules. Both these features can be contemporarily endued to a multitude of membrane monoliths.

Composite GO/Ceramic Membranes Prepared via Chemical Attachment: Characterisation and Gas Permeance Properties.

Graphene oxide (GO) oligo-layered laminates were self-assembled on porous ceramic substrates via their simple dip-coating into aqueous GO dispersions. To augment the stability of the developed composite GO/ceramic membranes and control the morphology and stacking quality of the formed laminate, short-((3-glycidoxypropyl)trimethoxy silane-GLYMO, (3-aminopropyl)triethoxy silane-APTES), and long-chain (polydopamine-PDA) molecules were involved and examined as interfacial linkers. A comparative study was performed regarding the linker's capacity to enhance the interfacial adhesion between the ceramic surface and the GO deposit and affect the orientation and assemblage characteristics of the adjacent GO nanosheets that composed the formed oligo-layered laminates.

Engineering Commercial TiO Powder into Tailored Beads for Efficient Water Purification.

In this study, efficient commercial photocatalyst (Degussa P25) nanoparticles were effectively dispersed and stabilized in alginate, a metal binding biopolymer. Taking advantage of alginate's superior metal chelating properties, copper nanoparticle-decorated photocatalysts were developed after a pyrolytic or calcination-sintering procedure, yielding ceramic beads with enhanced photocatalytic and mechanical properties, excellent resistance to attrition, and optimized handling compared to powdered photocatalysts. The morphological and structural characteristics were studied using LN porosimetry, SEM, and XRD.

Structuring efficient photocatalysts into bespoke fiber shaped systems for applied water treatment.

In this study, structured photocatalytic systems were successfully developed by a facile method based on Alginate molds and a wet-spinning/cross-linking technique, yielding commercial photocatalyst (Degussa P25) in the form of all-ceramic hollow fibers (HFs). Taking advantage of alginate's exceptional sorption properties, copper augmented HFs were also developed. The structured photocatalysts were thoroughly characterised by a variety of techniques, including nitrogen adsorption, SEM/EDS, XRD, XPS and Raman.

CO/CH and He/N Separation Properties and Water Permeability Valuation of Mixed Matrix MWCNTs-Based Cellulose Acetate Flat Sheet Membranes: A Study of the Optimization of the Filler Material Dispersion Method.

The main scope of this work is to develop nano-carbon-based mixed matrix cellulose acetate membranes (MMMs) for the potential use in both gas and liquid separation processes. For this purpose, a variety of mixed matrix membranes, consisting of cellulose acetate (CA) polymer and carbon nanotubes as additive material were prepared, characterized, and tested. Multi-walled carbon nanotubes (MWCNTs) were used as filler material and diacetone alcohol (DAA) as solvent.

Detecting IoT User Behavior and Sensitive Information in Encrypted IoT-App Traffic.

Many people use smart-home devices, also known as the Internet of Things (IoT), in their daily lives. Most IoT devices come with a companion mobile application that users need to install on their smartphone or tablet to control, configure, and interface with the IoT device. IoT devices send information about their users from their app directly to the IoT manufacturer's cloud; we call this the "app-to-cloud way".