Characterisation and use of biomass fly ash in cement-based materials.

This paper presents results about the characterisation of the biomass fly ashes sourced from a thermal power plant and from a co-generation power plant located in Portugal, and the study of new cement formulations incorporated with the biomass fly ashes. The study includes a comparative analysis of the phase formation, setting and mechanical behaviour of the new cement-fly ash formulations based on these biomass fly ashes. Techniques such as X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF), thermal gravimetric and differential thermal analysis (TG/DTA), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and environmental scanning electron spectroscopy (ESEM) were used to determine the structure and composition of the formulations.

Inhibition of hydroxyapatite dissolution by whole casein: the effects of pH, protein concentration, calcium, and ionic strength.

Formulating drinks with reduced erosive potential is one approach for reducing dental erosion. In this study, whole casein was added to citric acid solutions representative of soft drinks, and the hydroxyapatite dissolution rate was assessed. Adding 0.

An investigation of some food-approved polymers as agents to inhibit hydroxyapatite dissolution.

Dental erosion involves dissolution of the hydroxyapatite fraction of enamel and dentine, so agents that reduce the dissolution rate of hydroxyapatite could find application in food products aimed at reducing erosion. This study was performed to test some common food ingredients and additives for their effect on the dissolution rate of hydroxyapatite in a citric acid solution representative of soft drinks. Pyrophosphate, tripolyphosphate and a linear chain polyphosphate (average 25 phosphate units) significantly reduced the hydroxyapatite dissolution rate by 35, 46 and 64%, respectively.

Enamel dissolution in citric acid as a function of calcium and phosphate concentrations and degree of saturation with respect to hydroxyapatite.

The aim of this study was to investigate enamel dissolution in citric acid solutions as a function of solution calcium and phosphate concentrations and degree of saturation with respect to hydroxyapatite (DSHA). The primary relevance of the study is the development of soft drinks with reduced erosive potential. Nanoindentation was used to investigate changes in the hardness of polished human enamel surfaces after 120 s and 300 s exposure to solutions with pH 3.

Human enamel dissolution in citric acid as a function of pH in the range 2.30< or =pH< or =6.30--a nanoindentation study.

The objective of this study was to investigate the dissolution of human enamel in citric acid solutions over a wide range of pH. The in vitro conditions are considered to be relevant to soft drink-induced enamel erosion. Nanoindentation was used to investigate changes in the nanomechanical properties of polished enamel surfaces after exposure to citric acid solutions.

Mechanical properties and radiopacity of experimental glass-silica-metal hybrid composites.

Objectives: Experimental glass-silica-metal hybrid composites (polycomposites) were developed and tested mechanically and radiographically in this fundamental pilot study. To determine whether mechanical properties of a glass-silica filled two-paste dental composite based on a Bis-GMA/polyglycol dimethacrylate blend could be improved through the incorporation of titanium (Ti) particles (particle size ranging from 1 to 3 microm) or silver-tin-copper (Ag-Sn-Cu) particles (particle size ranging from 1 to 50 microm) we measured the diametral tensile strength, fracture toughness and radiopacity of five composites.

Methods: The five materials were: I, the original unmodified composite (control group); II, as group I but containing 5% (wt/wt) of Ti particles; III, as group II but with Ti particles treated with 4-methacryloyloxyethyl trimellitate anhydride (4-META) to promote Ti-resin bonding; IV, as group I but containing 5% (wt/wt) of Ag-Sn-Cu particles; and V, as group IV but with the metal particles treated with 4-META.