Bi-stability in femtosecond laser ablation by MHz bursts.

In this work, a bi-stable behavior of laser ablation efficiency and quality was controlled by fluence and burst length. The plasma shielding of incoming laser radiation caused sudden jumps with a significant decrease in ablation efficiency for every even number of pulses in the burst. The attenuation of incoming laser radiation by plasma created by the previous pulse was incorporated into the toy model of burst ablation efficiency.

Fabrication of a multilevel Fresnel axicon deep in fused silica by femtosecond laser machining.

This manuscript presents a simple approach to the manufacturing and optimization of a multilevel phase-only diffractive conical lens (Fresnel axicon or "fraxicon"). The method for recording deep type I modifications in fused silica was established and its ability proven. We showed the prospects and limitations of elements processed using this method.

Effect of Femtosecond Laser-Irradiated Titanium Plates on Enhanced Antibacterial Activity and Preservation of Bacteriophage Stability.

Titanium (Ti) is widely recognized for its exceptional properties and compatibility with medical applications. In our study, we successfully formed laser-induced periodic surface structures (LIPSS) on Ti plates with a periodicity of 520-740 nm and a height range of 150-250 nm. To investigate the morphology and chemical composition of these surfaces, we employed various techniques, including field emission scanning electron microscopy, energy dispersive X-ray spectroscopy, atomic force microscopy, X-ray photoelectron spectroscopy, and Raman spectroscopy.

Investigation of the modifications properties in fused silica by the deep-focused femtosecond pulses.

In this study, we demonstrate the elongated Type I modifications in fused silica with an axial length > 50 µm. Such extended longitudinal dimensions were obtained by deep focusing radiation of a femtosecond laser inside fused silica at a depth of 2 mm. The transition from the Type II modification (nanogratings) to the Type I modification (refraction index change) was observed with increasing focusing depth at the constant pulse energy.

Efficient surface polishing using burst and biburst mode ultrafast laser irradiation.

The use of laser irradiation for micromachining is widely applicable and has many benefits. One of the main uses is that it is possible to mill and polish the sample using the same laser system. State-of-the-art laser systems with high average optical power and burst regimes are widely used in technology.

Femtosecond Laser Cutting of 110-550 µm Thickness Borosilicate Glass in Ambient Air and Water.

The cutting quality and strength of strips cut with femtosecond-duration pulses were investigated for different thicknesses of borosilicate glass plates. The laser pulse duration was 350 fs, and cutting was performed in two environments: ambient air and water. When cutting in water, a thin flowing layer of water was formed at the front surface of the glass plate by spraying water mist next to a laser ablation zone.

Efficient Water-Assisted Glass Cutting with 355 nm Picosecond Laser Pulses.

In this study, the cutting of borosilicate glass plates in ambient air and water with a 355 nm wavelength picosecond laser was carried out. Low (2.1-2.

Quality and flexural strength of laser-cut glass: classical top-down ablation versus water-assisted and bottom-up machining.

The growing applicability of glass materials drives the development of novel processing methods, which usually lack comprehensive comparison to conventional or state-of-art ones. That is especially delicate for assessing the flexural strength of glass, which is highly dependent on many factors. This paper compares the traditional top-down laser ablation methods in the air to those assisted with a flowing water film using picosecond pulses.

Transversal and axial modulation of axicon-generated Bessel beams using amplitude and phase masks for glass processing applications.

The control of laser-induced microcracks in the volume of transparent materials is essential for scribing processes. In this paper, we investigate the effect of various amplitude and single-level phase masks on both transverse and axial intensity distribution of the conventional axicon-generated Bessel beams. Furthermore, we demonstrate the volumetric crack control induced by an asymmetrical central core with an appropriately selected intensity level to avoid the influence of peripheral intensity maxima.

Chemical etching of fused silica after modification with two-pulse bursts of femtosecond laser.

Bursts of femtosecond laser pulses were used to record internal modifications inside fused silica for selective chemical etching. Two-pulse bursts with a variable energy ratio between those pulses at a fixed inter-pulse duration of 14.5 ns were applied for the first time.

Symmetric and asymmetric shocked gas jets for laser-plasma experiments.

Shocks in supersonic flows offer both high density and sharp density gradients that are used, for instance, for gradient injection in laser-plasma accelerators. We report on a parametric study of oblique shocks created by inserting a straight axisymmetric section at the end of a supersonic "de Laval" nozzle. The effect of different parameters, such as the throat diameter and straight section length on the shock position and density, is studied through computational fluid dynamics (CFD) simulations.

Femtosecond laser ablation by bibursts in the MHz and GHz pulse repetition rates.

Here, to the best of our knowledge, for the first time we report an in-depth experimental study of high ultrafast laser ablation efficiency for processing of copper and steel with single-pulses, MHz, GHz, and burst-in-the-burst (biburst) regimes. The comparison of burst, biburst, and single-pulse ablation efficiencies was performed for beam-size-optimised regimes, showing the real advantages and disadvantages of milling and drilling processing approaches. Highly efficient ultrashort pulse laser processing was achieved for ∼1 µm optical wavelength: 8.

Influence of nonlinear and saturable absorption on laser lift-off threshold of an oxide/metal structure.

In this work, a new, to the best of our knowledge, model of effective lift-off threshold of an oxide/metal target is presented. The influence of nonlinear processes in the oxide layer on its removal from the metallic samples using a picosecond laser was investigated. Nonlinear and saturable absorption in the layer was incorporated into modeling for prediction of effective laser lift-off threshold fluence change with varying peak intensities in a -scan-type experiment for the first time.

In-depth comparison of conventional glass cutting technologies with laser-based methods by volumetric scribing using Bessel beam and rear-side machining.

With the development of industrial lasers and novel glass processing techniques, which offer high speed, quality and precision, this becomes an attractive alternative to conventional methods, such as mechanical scribing and cleaving, diamond saw and waterjet cutting, commonly used in the industry. However, the emerging techniques lack thorough validation with respect to well-established methods. To this end, we present a detailed comparison of different glass cutting methods, taking into account surface quality, side-wall roughness, residual stresses and flexural strength.

Controlling the wettability of stainless steel from highly-hydrophilic to super-hydrophobic by femtosecond laser-induced ripples and nanospikes.

Results on the manipulation of the wetting properties of stainless steel alloy surface by ultrashort pulse laser texturing are presented. The wide range of water droplet contact angles from highly-hydrophilic to super-hydrophobic was achieved by generation of laser-induced periodic surface structures (LIPSS) and nanospikes. In particular, the wetting state was controlled by accumulated laser fluence, which determines the carbon/oxygen content and nano-texture type of the surface after laser treatment.

Laser wakefield accelerated electron beams and betatron radiation from multijet gas targets.

Laser Plasma Wakefield Accelerated (LWFA) electron beams and efficiency of betatron X-ray sources is studied using laser micromachined supersonic gas jet nozzle arrays. Separate sections of the target are used for the injection, acceleration and enhancement of electron oscillation. In this report, we present the results of LWFA and X-ray generation using dynamic gas density grid built by shock-waves of colliding jets.

Improvement of Etching Anisotropy in Fused Silica by Double-Pulse Fabrication.

Femtosecond laser-induced selective etching (FLISE) is a promising technology for fabrication of a wide range of optical, mechanical and microfluidic devices. Various etching conditions, together with significant process optimisations, have already been demonstrated. However, the FLISE technology still faces severe limitations for a wide range of applications due to limited processing speed and polarization-dependent etching.

Direct and High-Throughput Fabrication of Mie-Resonant Metasurfaces Single-Pulse Laser Interference.

High-index dielectric metasurfaces featuring Mie-type electric and magnetic resonances have been of great interest in a variety of applications such as imaging, sensing, photovoltaics, and others, which led to the necessity of an efficient large-scale fabrication technique. To address this, here we demonstrate the use of single-pulse laser interference for direct patterning of an amorphous silicon film into an array of Mie resonators a few hundred nanometers in diameter. The proposed technique is based on laser-interference-induced dewetting.

Laser-induced spatially-selective tailoring of high-index dielectric metasurfaces.

Optically resonant high-index dielectric metasurfaces featuring Mie-type electric and magnetic resonances are usually fabricated by means of planar technologies, which limit the degrees of freedom in tunability and scalability of the fabricated systems. Therefore, we propose a complimentary post-processing technique based on ultrashort (≤ 10 ps) laser pulses. The process involves thermal effects: crystallization and reshaping, while the heat is localized by a high-precision positioning of the focused laser beam.

Laser-fabricated axicons challenging the conventional optics in glass processing applications.

Laser-based fabrication can be an alternative technology to mechanical grinding and polishing processes. However, the performance of these elements in real applications still needs to be validated. In this paper, we demonstrate that the subtractive fabrication technology is able to produce high-quality axicons from fused silica, which can be efficiently used for glass processing.

Highly-efficient laser ablation of copper by bursts of ultrashort tuneable (fs-ps) pulses.

Ultrashort pulse laser, capable of varying pulse duration between 210 fs and 10 ps and producing a burst of pulses with an intra-burst pulse repetition rate of 64.5 MHz (time distance between pulses 15.5 ns), was used to investigate the ablation efficiency of the copper.

Advanced laser scanning for highly-efficient ablation and ultrafast surface structuring: experiment and model.

Ultra-short laser pulses are frequently used for material removal (ablation) in science, technology and medicine. However, the laser energy is often used inefficiently, thus, leading to low ablation rates. For the efficient ablation of a rectangular shaped cavity, the numerous process parameters such as scanning speed, distance between scanned lines, and spot size on the sample, have to be optimized.

High-density gas capillary nozzles manufactured by hybrid 3D laser machining technique from fused silica.

In this report, an efficient hybrid laser technique, nanosecond laser rear-side processing and femtosecond laser-assisted selective etching (FLSE) for the manufacturing of high-density gas capillary targets, is demonstrated. Cylindrical capillary nozzles for laser betatron X-ray sources were numerically simulated, manufactured from fused silica by 3D laser inscription and characterized using interferometry and gas density reconstruction. The dependence of gas concentration profiles on the wall roughness of cylindrical channels is presented.

Laser Irradiation of Gd-Si and Gd-Si-Ge Colloid Mixtures for the Fabrication of Compound Nanoparticles.

Binary (Gd Si , GdSi) and ternary (Gd Si Ge ) compound nanoparticles (NPs) were prepared by laser irradiation of a mixture of colloidal solutions containing NPs of the relevant elements. It is assumed that the compound NPs are formed by heating, co-melting, and chemical interactions in the alloyed droplets. The blackbody-like radiation of the heated NPs was used for temperature control of the NP-preparation process.

Aberration-controlled Bessel beam processing of glass.

It is known that Bessel beam generation with a non-ideal axicon induces beam pattern distortions. In this paper, we introduce a simple method for non-ideal axicon-generated Bessel beam reconstruction by tilting the axicon perpendicular to its optical axis. We found an optimum axicon tilt angle where beam distortions can be compensated by inducing additional astigmatic aberrations.