Mass-manufacturable scintillation-based optical fiber dosimeters for brachytherapy.

Scintillation-based fiber dosimeters are a powerful tool for minimally invasive localized real-time monitoring of the dose rate during Low Dose Rate (LDR) and High Dose Rate (HDR) brachytherapy (BT). This paper presents the design, fabrication, and characterization of such dosimeters, consisting of scintillating sensor tips attached to polymer optical fiber (POF). The sensor tips consist of inorganic scintillators, i.

Intermodal phase and group velocity matching for frequency tripling and doubly phase matched cascaded wave mixing in high index contrast double-clad optical fibers.

Frequency conversion in glass optical fibers requires both phase and group velocity matching between the pump and the higher harmonic when working with short pulses. We show that phase and group velocities can be matched simultaneously for third order nonlinear processes, by considering that the third harmonic propagates in the higher order azimuthally symmetric LP-mode. Moreover, the pump and frequency tripled signals can form an intermodal two-color pump to trigger a cascaded wave mixing process, which generates the second harmonic LP-mode.

Freeform Wide Field-of-View Spaceborne Imaging Telescope: From Design to Demonstrator.

Wide field-of-view imaging optics offer a huge potential for space-based Earth observation enabling the capture of global data. Reflective imaging telescopes are often favored, as they do not show chromatic aberrations and are less susceptible to radiation darkening than their refractive counterparts. However, the main drawback of reflective telescopes is that they are limited with respect to field-of-view while featuring large dimensions.

Highly birefringent microstructured optical fiber for distributed hydrostatic pressure sensing with sub-bar resolution.

We demonstrate distributed optical fiber-based pressure measurements with sub-bar pressure resolution and 1 m spatial resolution over a ∼100 m distance using a phase-sensitive optical time-domain reflectometry technique. To do so, we have designed a novel highly birefringent microstructured optical fiber that features a high pressure to temperature sensitivity ratio, a high birefringence and a mode field diameter that is comparable to that of conventional step-index single mode fibers. Our experiments with two fibers fabricated according to the design confirm the high polarimetric pressure sensitivities (-62.

Optical Design of a Novel Wide-Field-of-View Space-Based Spectrometer for Climate Monitoring.

We report on a near-infrared imaging spectrometer for sensing the three most prominent greenhouse gases in the atmosphere (water vapor, carbon dioxide and methane). The optical design of the spectrometer involves freeform optics, which enables achieving exceptional performance and allows progressing well beyond the state-of-the-art in terms of compactness, field-of-view, and spatial resolution. The spectrometer is intended to be launched on a small satellite orbiting at 700 km and observing the Earth with a wide field-of-view of 120° and a spatial resolution of 2.

Simultaneous modal phase and group velocity matching in microstructured optical fibers for second harmonic generation with ultrashort pulses.

Optical fibers provide a favorable medium for nonlinear optical processes owing to the small mode field size and concurrently high optical intensity combined with the extended interaction lengths. Second harmonic generation (SHG) is one of those processes that has been demonstrated in silica glass optical fibers. Since silica is centrosymmetric, generating SHG in an optical fiber requires poling of the glass.

Wide-Field-of-View Longwave Camera for the Characterization of the Earth's Outgoing Longwave Radiation.

The measurement of the Earth's Outgoing Longwave Radiation plays a key role in climate change monitoring. This measurement requires a compact wide-field-of-view camera, covering the 8-14 µm wavelength range, which is not commercially available. Therefore, we present a novel thermal wide-field-of-view camera optimized for space applications, featuring a field of view of 140° to image the Earth from limb to limb, while enabling a high spatial resolution of 4.

Challenges in the Fabrication of Biodegradable and Implantable Optical Fibers for Biomedical Applications.

The limited penetration depth of visible light in biological tissues has encouraged researchers to develop novel implantable light-guiding devices. Optical fibers and waveguides that are made from biocompatible and biodegradable materials offer a straightforward but effective approach to overcome this issue. In the last decade, various optically transparent biomaterials, as well as different fabrication techniques, have been investigated for this purpose, and in view of obtaining fully fledged optical fibers.

Monitoring of Torque Induced Strain in Composite Shafts with Embedded and Surface-Mounted Optical Fiber Bragg Gratings.

In this study, silica glass, optical fiber Bragg gratings (FBGs) are used for torque-induced strain monitoring in carbon fiber reinforced polymer (CFRP) hollow shafts toward the development of a methodology for structural load monitoring. Optical fibers with gratings are embedded during shaft manufacturing, by an industrial filament winding process, along different orientations with respect to its central axis and surface mounted after production. Experimental results are supported by numerical modeling of the shaft with appropriate boundary conditions and homogenized material properties.

Spectral Verification of the Mechanisms behind FBG-Based Ultrasonic Guided Wave Detection.

Ultrasonic guided wave (UGW) detection with fiber Bragg grating (FBG)-based sensors has received increasing attention in the last decades due to the ability to perform non-destructive inspection (NDI) of large plate-like surfaces with a network of lightweight and multiplexed sensors. For accurate UGW measurements, several studies concluded that the ratio between the wavelength of the UGW and the length of the FBG should be above 7. However, shorter FBGs suffer from a lower FBG reflectivity and less steep slopes in the reflection spectrum.

Effect of hydrogen gas on FBG-based optical fiber sensors for downhole pressure and temperature monitoring.

The influence of hydrogen gas on Fiber Bragg Grating (FBG)-based optical fiber sensors has been validated experimentally. More in particular, the focus was on FBGs written in the so-called Butterfly Micro Structured Fiber that targets simultaneous pressure and temperature monitoring with a minimum in cross-sensitivity to be used in, for example, downhole applications for the oil and gas market. The hydrogen-induced pressure and temperature errors from this type of sensor have been quantified as a function of the partial hydrogen pressure.

IR femtosecond pulsed laser-based fiber Bragg grating inscription in a photonic crystal fiber using a phase mask and a short focal length lens.

Fiber Bragg grating inscription with infrared femtosecond pulsed lasers in photonic crystal fiber is far from being trivial due to the presence of air holes in the cladding region and the non-linear nature of the absorption process inducing the required refractive index changes. We have studied this problem numerically and experimentally for a phase mask-based writing setup equipped with short focal length cylindrical lenses, which are often used for through-coating and high temperature stable grating writing. We have shown that for a cylindrical lens with a focal length f of 10 mm, the hexagonal lattice PCF needs to be translated away from the beam waist position by around 15 µm to efficiently deliver the energy to the core region.

Anomalous transparency in photonic crystals and its application to point-by-point grating inscription in photonic crystal fibers.

It is common belief that photonic crystals behave similarly to isotropic and transparent media only when their feature sizes are much smaller than the wavelength of light. Here, we counter that belief and we report on photonic crystals that are transparent for anomalously high normalized frequencies up to 0.9, where the crystal's feature sizes are comparable with the free space wavelength.

Fibre Bragg Gratings in Embedded Microstructured Optical Fibres Allow Distinguishing between Symmetric and Anti-Symmetric Lamb Waves in Carbon Fibre Reinforced Composites.

Conventional contact sensors used for Lamb wave-based ultrasonic inspection, such as piezo-electric transducers, measure omnidirectional strain and do not allow distinguishing between fundamental symmetric and anti-symmetric modes. In this paper, we show that the use of a single fibre Bragg grating created in a dedicated microstructured optical fibre allows one to directly make the distinction between these fundamental Lamb wave modes. This feature stems from the different sensitivities of the microstructured fibre to axial and transverse strain.

FBGs written in specialty fiber for high pressure/high temperature measurement.

In this paper, we evaluate different thermal treatments in order to stabilize fiber Bragg gratings written by a femtosecond pulsed laser in specialty highly birefringent micro-structured optical fiber, targeting pressure monitoring at high pressure and high temperature environments. We have obtained a pressure sensitivity of 3.30 pm/bar up to 1400 bar and 290 °C.

Thermal effects on the photoelastic coefficient of polymer optical fibers.

We measure the radial profile of the photoelastic coefficient C(r) in single-mode polymer optical fibers (POFs), and we determine the evolution of C(r) after annealing the fibers at temperatures from 40°C to 80°C. We demonstrate that C(r) in the fibers drawn from a preform without specific thermal pre-treatment changes and converges to values between 1.2 and 1.

Vibration Monitoring Using Fiber Optic Sensors in a Lead-Bismuth Eutectic Cooled Nuclear Fuel Assembly.

Excessive fuel assembly vibrations in nuclear reactor cores should be avoided in order not to compromise the lifetime of the assembly and in order to prevent the occurrence of safety hazards. This issue is particularly relevant to new reactor designs that use liquid metal coolants, such as, for example, a molten lead-bismuth eutectic. The flow of molten heavy metal around and through the fuel assembly may cause the latter to vibrate and hence suffer degradation as a result of, for example, fretting wear or mechanical fatigue.

Algorithms for determining the radial profile of the photoelastic coefficient in glass and polymer optical fibers.

We discuss two algorithms to determine the value and the radial profile of the photoelastic coefficient C in glass and polymer optical fibers. We conclude that C is constant over the fiber cross-sections, with exception of silica glass fibers containing a fluorine-doped depressed cladding. In the undoped and Ge-doped parts of these silica glass fibers we find a consistent value for C that is slightly larger than in bulk silica.

A micro-computed tomography technique to study the quality of fibre optics embedded in composite materials.

Quality of embedment of optical fibre sensors in carbon fibre-reinforced polymers plays an important role in the resultant properties of the composite, as well as for the correct monitoring of the structure. Therefore, availability of a tool able to check the optical fibre sensor-composite interaction becomes essential. High-resolution 3D X-ray Micro-Computed Tomography, or Micro-CT, is a relatively new non-destructive inspection technique which enables investigations of the internal structure of a sample without actually compromising its integrity.

Numerical modeling of femtosecond laser inscribed IR gratings in photonic crystal fibers.

During grating inscription in photonic crystal fibers (PCFs) the intensity of the inscribing laser beam is non-uniformly distributed over the core region due to the interaction with the air holes in the fiber's microstructure. In this paper we model and study the non-uniformity of the index modification and its influence on the grating reflection spectra, taking into account the non-linear nature of the index change. For femtosecond laser inscription pulses at 800 nm, we show that the intensity redistribution in the PCF core region can result in Type II index changes even if the peak intensity of the incident beam is well below the corresponding threshold.

Influence of fiber Bragg grating spectrum degradation on the performance of sensor interrogation algorithms.

The working principle of fiber Bragg grating (FBG) sensors is mostly based on the tracking of the Bragg wavelength shift. To accomplish this task, different algorithms have been proposed, from conventional maximum and centroid detection algorithms to more recently-developed correlation-based techniques. Several studies regarding the performance of these algorithms have been conducted, but they did not take into account spectral distortions, which appear in many practical applications.

Shear stress sensing with Bragg grating-based sensors in microstructured optical fibers.

We demonstrate shear stress sensing with a Bragg grating-based microstructured optical fiber sensor embedded in a single lap adhesive joint. We achieved an unprecedented shear stress sensitivity of 59.8 pm/MPa when the joint is loaded in tension.

Temperature-insensitive polarimetric vibration sensor based on HiBi microstructured optical fiber.

A new type of highly birefringent microstructured optical fiber has been tested for vibration measurements using a polarimetric technique. This technique takes advantage of the stress-induced phase shift between the two orthogonally polarized fiber eigenmodes. Comparison of three different fiber types shows that standard single-mode fibers do not provide stable measurements and that conventional polarization-maintaining fibers lead to a significant cross-sensitivity to temperature.

Microstructured optical fiber sensors embedded in a laminate composite for smart material applications.

Fiber Bragg gratings written in highly birefringent microstructured optical fiber with a dedicated design are embedded in a composite fiber-reinforced polymer. The Bragg peak wavelength shifts are measured under controlled axial and transversal strain and during thermal cycling of the composite sample. We obtain a sensitivity to transversal strain that exceeds values reported earlier in literature by one order of magnitude.