New system for the detection of Legionella pneumophila in water samples.

Waterborne pathogens are a global concern for public health worldwide. Despite continuing efforts to maintain water safety, water quality is still affected by deterioration and pollution. Legionella pneumophila colonizes man-made water systems and can infect humans causing Legionnaire's disease (LD), pneumonia.

Antibody test for Legionella pneumophila detection.

Legionella pneumophila is responsible for Legionnaires' disease (LD). Its detection in both environmental and clinical samples is mainly performed by culture plate method which requires up to 10days to obtain results. Nowadays, there are commercial antibodies against this bacterium, but they have not been tested against all subgroups of L.

Impedimetric antimicrobial peptide-based sensor for the early detection of periodontopathogenic bacteria.

Peri-implantitis, an inflammation caused by biofilm formation, constitutes a major cause of implant failure in dentistry. Thus, the detection of bacteria at the early steps of biofilm growth represents a powerful strategy to prevent implant-related infections. In this regard, antimicrobial peptides (AMPs) can be used as effective biological recognition elements to selectively detect the presence of bacteria.

Membraneless glucose/O2 microfluidic enzymatic biofuel cell using pyrolyzed photoresist film electrodes.

Biofuel cells typically yield lower power and are more difficult to fabricate than conventional fuel cells using inorganic catalysts. This work presents a glucose/O2 microfluidic biofuel cell (MBFC) featuring pyrolyzed photoresist film (PPF) electrodes made on silicon wafers using a rapid thermal process, and subsequently encapsulated by rapid prototyping techniques into a double-Y-shaped microchannel made entirely of plastic. A ferrocenium-based polyethyleneimine polymer linked to glucose oxidase (GOx/Fc-C6-LPEI) was used in the anode, while the cathode contained a mixture of laccase, anthracene-modified multi-walled carbon nanotubes, and tetrabutylammonium bromide-modified Nafion (MWCNTs/laccase/TBAB-Nafion).

Design and fabrication of a COP-based microfluidic chip: chronoamperometric detection of Troponin T.

This work demonstrates the design and fabrication of an all cyclo-olefin polymer based microfluidic device capable of capturing magnetic beads and performing electrochemical detection in a series of gold electrodes. The size of chip is of a microscope slide and features six independent measuring cells for multianalyte detection purposes. The aim of this work is to show that rapid prototyping techniques can be instrumental in the development of novel bioassays, particularly in clinical diagnosis applications.

Transient storage of electrical charge in biofilms of Shewanella oneidensis MR-1 growing in a microbial fuel cell.

Current output of microbial fuel cells (MFCs) depends on a number of engineering variables mainly related to the design of the fuel cell reactor and the materials used. In most cases the engineering of MFCs relies on the premise that for a constant biomass, current output correlates well with the metabolic activity of the cells. In this study we analyze to what extent, MFC output is also affected by the mode of operation, emphasizing how discontinuous operation can affect temporal patterns of current output.

Electrochemical detection of quorum sensing signaling molecules by dual signal confirmation at microelectrode arrays.

n-Acyl homoserine lactones (AHLs) are produced by gram-negative bacteria to regulate gene expression in a cell density dependent manner. For instance, expression of virulence factors by pathogens such as Pseudomonas aeruginosa is induced only when a threshold concentration of AHLs is reached, which indicates that the bacterial population is big enough to promote infection. In this study, the indicator strain Agrobacterium tumefaciens NTL4 (pZLR4), which carries a β-galactosidase (β-gal) reporter gene under the control of a quorum sensing promoter, was used to develop an electrochemical biosensor to detect AHLs using the model n-(3-oxo)-dodecanoyl-L-homoserine lactone (oxo-C12-HSL), an AHL previously detected in cystic fibrosis patients infected with P.

Integration of a zero dead-volume PDMS rotary switch valve in a miniaturised (bio)electroanalytical system.

This work features the design, fabrication and characterisation of a miniaturised electroanalytical lab on a chip that allows the performance of a complete bioassay, from the capture of magnetic particles through their functionalisation and sample incubation to the detection of electroactive reaction products. The system is built using mainly polymeric materials such as PMMA and PDMS and fast prototyping techniques such as milling and moulding. The system also includes a set of microelectrodes, photo-lithographed on a silicon chip.

Magnetic entrapment for fast, simple and reversible electrode modification with carbon nanotubes: application to dopamine detection.

Carbon nanotubes (CNT) have been exploited for an important number of electroanalytical and sensing purposes. Specifically, CNT incorporation to an electrode surface coating increases its roughness and area, provides electrocatalytic activity towards a variety of molecules, and improves electron transfer. This modification is generally based on the irreversible deposition of CNT on surface.

Captavidin: a new regenerable biocomponent for biosensing?

Functionalisation of a biosensor's sensing surface with the appropriate biorecognition elements is essential for the correct performance of the biosensor. In this paper, we investigate by Surface Plasmon Resonance (SPR) if captavidin, a recently described biotin-binding regenerable protein, could be used to bind and release biotinylated biocomponents for the development of regenerable biosensors. In our experiments, biotinylated antibodies were successfully subjected to up to nine serial capture-release events from the captavidin-functionalised surface.

Why 'the bigger the better' is not always the case when utilising microelectrode arrays: high density vs. low density arrays for the electroanalytical sensing of chromium(VI).

We demonstrate, with the example of the electroanalytical sensing of chromium(vi) using ultra-microelectrode arrays, that a larger number of microelectrodes comprising an array do not necessarily provide improved electroanalytical performance. Using a low density array, which consists of 256 microdiscs where each microdisc comprising the array has a radius of 10 microns in a cubic arrangement separated from their nearest neighbour by 100 microns, the electroanalytical sensing of chromium(vi) is shown to be possible over the range 13-428 microM with a limit of detection of 3.4 microM readily achievable.

Microarrays of ring-recessed disk electrodes in transient generator-collector mode: theory and experiment.

The fabrication, characterization, and use of arrays of ring-recessed disk microelectrodes are reported. These devices are operated in generator-collector mode with a disk acting as the generator and the ring as the collector. We report experiments and simulations relating to time-of-flight experiments in which material electrogenerated at a disk is diffusionally transported to the ring.

Biosensing at disk microelectrode arrays. Inter-electrode functionalisation allows formatting into miniaturised sensing platforms of enhanced sensitivity.

Biosensor performance depends on the effective functionalisation of a transducer with suitable biorecognition elements. During functionalisation, surface blocking steps are normally carried out to avoid later binding of undesirable molecules and thus guarantee biosensor specificity. However, these blocking steps may be deleterious in electrochemical systems where transduction ultimately relies on electron transfer between the electrode and a redox species in solution.

Investigating the concept of diffusional independence. Potential step transients at nano- and micro-electrode arrays: theory and experiment.

Microelectrode arrays find broad application in electroanalysis offering the enhanced sensitivity associated with microelectrodes, but with a high total current output. Such arrays are often constructed to make the electrodes 'diffusionally independent'. To emphasize that this is a time dependent property, a two-dimensional simulation, in conjunction with the diffusional domain approach, is used to model potential step transient currents at microelectrode arrays.

Detection of Escherichia coli and Salmonella typhimurium using interdigitated microelectrode capacitive immunosensors: the importance of transducer geometry.

This paper presents an immunosensing system to detect Escherichia coli and Salmonella based on electrochemical impedance spectroscopy at interdigitated electrode structures. Our results show the importance of good electrode design in the final detection limit. Four different structures have been fabricated and functionalized.

Sensing bacteria but treating them well: determination of optimal incubation and storage conditions.

Bacteria detection in real samples often involves long and tedious methodologies such as culture enrichment, biochemical screening, and serological confirmation. In this context, the development of biosensors and quick assays for bacteria detection appears as fast growing fields. However, a detailed study of reports in these areas reveals the existence of important differences in bacteria storage, handling, and detection conditions, indicating that authors do not take advantage of the well-established procedures existing for classical techniques such as enzyme-linked immunosorbent assay (ELISA).

Enzyme shadowing: using antibody-enzyme dually-labeled magnetic particles for fast bacterial detection.

Using magnetic particles and immunoseparation for target recovery and detection has been reported to improve the performance and detection limits of traditional analytical methods. For example, magnetic immunocapture can be coupled to detection in a sandwich format using an antibody (Ab) labeled with a reporter molecule or enzyme. In this work we demonstrate that simultaneous incorporation of capture and reporter biocomponents onto the sensing surface is possible and provides assays that are extremely fast and easy to carry out.

Immunofunctionalisation of gold transducers for bacterial detection by physisorption.

Functionalisation of the sensing surface is a key factor in immunosensor fabrication as it allows target-selective capture and prevents nonspecific adsorption of undesired components. Gold immunofunctionalisation using self-assembled monolayers (SAM) has been widely exploited to this end for the detection of small targets. However, we recently demonstrated that this strategy fails when detecting whole bacteria cells (Baldrich et al.

Gold immuno-functionalisation via self-assembled monolayers: study of critical parameters and comparative performance for protein and bacteria detection.

Surface functionalisation is of extreme importance in assay and biosensor development because it ensures the selective capture and detection of the targets of interest. In the present report, we compare the performance of several gold functionalisation strategies/chemistries, based on SAM self-assembly and Ab conjugation, for protein and bacteria detection. The first part of the work summarises the optimisation of the various protocols considered.

Surface plasmon resonance assay for real-time monitoring of somatic coliphages in wastewaters.

The surface plasmon resonance (SPR) technique is a well-established method for the measurement of molecules binding to surfaces and the quantification of binding constants between surface-immobilized proteins and proteins in solution. In this paper we describe an extension of the methodology to study bacteriophage-bacterium interactions. A two-channel microfluidic SPR sensor device was used to detect the presence of somatic coliphages, a group of bacteriophages that have been proposed as fecal pollution indicators in water, using their host, Escherichia coli WG5, as a target for their selective detection.

On-chip electric field driven electrochemical detection using a poly(dimethylsiloxane) microchannel with gold microband electrodes.

An external electric field driven in-channel detection technique for on-chip electrochemical detection in micro fabricated devices is described based on a microfluidic system containing an array of 20 microband electrodes. It is shown that an external electric field induces a potential difference between two gold microband electrodes in a poly(dimethylsiloxane) (PDMS) microchannel, and that this enables the electrochemical detection of electroactive species such as ascorbic acid and Fe(CN) 6 (4-). The results, which are supported by simulations of the behavior of the microband electrodes in the microfluidic system, show that the induced potential difference between the electrodes can be controlled by altering the external electric field or by using different microbands in the microband array.

Self-assembled monolayers as a base for immunofunctionalisation: unequal performance for protein and bacteria detection.

Biosensor development strongly depends on the optimisation of surface functionalisation strategies. When gold surfaces are considered, immunofunctionalisation by modification of self-assembled monolayers (SAMs) is one of the preferred approaches. In this respect, SAM-based antibody (Ab) incorporation has shown better performance than Ab physisorption for the detection of proteins and small targets.

Photoelectrochemical ruler: measurement at the micron scale.

A new approach to the measurement of objects with dimensions in the micron scale is proposed exploiting the spatial sensitivity of electrochemical measurements.

Diffusional protection of electrode surfaces using regular arrays of immobilised droplets: overcoming interferences in electroanalysis.

Regular arrays of ca. micron sized droplets on a gold electrode surface can block diffusion to the electrode surface of one metal ion (which binds with the material in the droplet) whilst having no significant effect on another (which does not), so allowing interference effects in electroanalysis to be eliminated.