Ergonomics appraisals in operating rooms.

This document presents the ergonomic assessments carried out by Spanish surgeons on the materials used within an operating room. With the objective of disseminating and raising awareness of the importance of ergonomics, this working group has compiled information from a previously conducted survey on musculoskeletal disorders associated with surgical work from the year 2022, obtaining feedback from 131 surgeons from 17 distinct specialties. A noteworthy 80.

Development of a Smart Leg Splint by Using New Sensor Technologies and New Therapy Possibilities.

Nowadays, after suffering a fracture in an upper or lower limb, a plaster cast is placed on the affected limb. It is a very old and efficient technique for recovery from an injury that has not had significant changes since its origin. This project aims to develop a new low-cost smart 3D printed splint concept by using new sensing techniques.

Efficient Upper Limb Position Estimation Based on Angular Displacement Sensors for Wearable Devices.

Motion tracking techniques have been extensively studied in recent years. However, capturing movements of the upper limbs is a challenging task. This document presents the estimation of arm orientation and elbow and wrist position using wearable flexible sensors (WFSs).

Development of a Smart Splint to Monitor Different Parameters during the Treatment Process.

For certain musculoskeletal complex rupture injuries, the only treatment available is the use of immobilization splints. This type of treatment usually causes discomfort and certain setbacks in patients. In addition, other complications are usually generated at the vascular, muscular, or articular level.

Behavior under Load of A Human Shoulder: Finite Element Simulation and Analysis.

Most musculoskeletal injuries occur during the work routines in different areas, due to repetitive and sustained movements, they are often located in the shoulder. For workers in the building sector, the repetitive movements and displacements occur under load and unnatural postures of the shoulder joint. For this reason, this study aims to model in 3D the biological components which form the shoulder joint for the later finite element analysis.

Novel Technique Based on Fused Filament Fabrication (FFF) and Robocasting to Create Composite Medical Parts.

The purpose for this study is to obtain a new composite manufacturing system based on Additive Manufacturing techniques that allows the creation of parts for the medical industry. These pieces will be resistant, lightweight and may have geometries more complex than those created with traditional systems of composite material. The new system is based on the union of two heads on a 3D Rep-Rap printer.

Monitoring an Analysis of Perturbations in Fusion Deposition Modelling (FDM) Processes for the Use of Biomaterials.

During an FDM production process, there are different external disturbances to the characteristics of the machine that can affect to the production process. These disturbances will cause the final result differs from the desired one. Moreover, these disturbances, such as temperature or chamber humidity, are extremely important in case of using biocompatible materials.

Experimental Comparison on Dental BioTribological Pairs Zirconia/Zirconia and Zirconia/Natural Tooth by Using a Reciprocating Tribometer.

The application of tribology in dentistry is growing rapidly, intense research has been conducted to develop an understanding of dental tribology for better selection of artificial materials and dental implant design. Dental biotribology, has been one of the most important branches in biotribology in recent years. The aim of this research is to investigate the tribological performances in the tooth-to-tooth contact and material-to-natural tooth contact (zirconia vs.

Filament Advance Detection Sensor for Fused Deposition Modelling 3D Printers.

The main purpose of this paper is to present a system to detect extrusion failures in fused deposition modelling (FDM) 3D printers by sensing that the filament is moving forward properly. After several years using these kind of machines, authors detected that there is not any system to detect the main problem in FDM machines. Authors thought in different sensors and used the weighted objectives method, one of the most common evaluation methods, for comparing design concepts based on an overall value per design concept.

Rapid prototyping prosthetic hand acting by a low-cost shape-memory-alloy actuator.

The purpose of this article is to develop a new concept of modular and operative prosthetic hand based on rapid prototyping and a novel shape-memory-alloy (SMA) actuator, thus minimizing the manufacturing costs. An underactuated mechanism was needed for the design of the prosthesis to use only one input source. Taking into account the state of the art, an underactuated mechanism prosthetic hand was chosen so as to implement the modifications required for including the external SMA actuator.

3D Digitization and Prototyping of the Skull for Practical Use in the Teaching of Human Anatomy.

The creation of new rapid prototyping techniques, low cost 3D printers as well as the creation of new software for these techniques have allowed the creation of 3D models of bones making their application possible in the field of teaching anatomy in the faculties of Health Sciences. The 3D model of cranium created in the present work, at full scale, present accurate reliefs and anatomical details that are easily identifiable by undergraduate students in their use for the study of human anatomy. In this article, the process of scanning the skull and the subsequent treatment of these images with specific software until the generation of 3D model using 3D printer has been reported.