Decoding in-plane orientation in cellulose nanopapers hybridized with tailored polymeric nanoparticles.

Biobased cellulose nanofibrils (CNFs) constitute important building blocks for biomimetic, nanostructured materials, and considerable potential exists in their hybridization with tailorable polymeric nanoparticles. CNFs naturally assemble into oriented, fibrillar structures in their cross-section. This work shows that polymeric nanoparticle additives have the potential to increase or decrease orientation of these cellulose structures, which allows the control of bulk mechanical properties.

Design of Extruded Nanostructured Composites via Decoupling of the Cellulose Nanofibril/Poly(butylene adipate--terephthalate) Interface.

The full exploitation of the outstanding mechanical properties of cellulose nanofibrils (CNFs) as potential reinforcements in nanocomposite materials is limited by the poor interactions at the CNF-polymer matrix interface. Within this work, tailor-made copolymers were designed to mediate the interface between CNFs and biodegradable poly(butylene adipate--terephthalate) (PBAT), and their effect on extruded nanocomposite performance was tested. For this purpose, two well-defined amphiphilic anchor-tail diblock copolymer structures were compared, with a fixed anchor block length and a large difference in the hydrophobic tail block length.

Self-Catalyzed Hydrolysis of Nitrile-Containing RAFT Chain-Transfer Agent and Its Impact upon Polymerization Control of Methacrylic Monomers.

Self-catalyzed hydrolysis upon storage of the common RAFT chain-transfer agent (CTA) 4-cyano-4-[(thiothiopropyl)sulfanyl] pentanoic acid (CTPPA) is confirmed, where the nitrile group is transformed into an amide by catalysis from the adjacent carboxylic acid moiety. The amide-CTA (APP) is found to poorly control molecular weight evolution during polymerization of two methacrylates, methyl methacrylate (MMA) and ,-(dimethylamino)ethyl methacrylate (DMAEMA), likely due to poor reinitiation speed in the pre-equilibrium. However, when attached to a macromolecule, the impact of this amide moiety becomes insignificant and chain extension proceeds as expected with CTPPA.

2-Methoxy-4-Vinylphenol as a Biobased Monomer Precursor for Thermoplastics and Thermoset Polymers.

To address the increasing demand for biobased materials, lignin-derived ferulic acid (FA) is a promising candidate. In this study, an FA-derived styrene-like monomer, referred to as 2-methoxy-4-vinylphenol (MVP), was used as the platform to prepare functional monomers for radical polymerizations. Hydrophobic biobased monomers derived from MVP were polymerized via solution and emulsion polymerization resulting in homo- and copolymers with a wide range of thermal properties, thus showcasing their potential in thermoplastic applications.

Nanolatex architectonics: Influence of cationic charge density and size on their adsorption onto surfaces with a 2D or 3D distribution of anionic groups.

Hypothesis: It is theoretically predicted and hypothesized that the charge density and size of spherical nanoparticles are the key factors for their adsorption onto oppositely charged surfaces. It is also hypothesized that the morphology and charge of the surface are of great importance. In-plane 2D (silica) or a volumetric 3D (regenerated TEMPO-oxidized cellulose model surfaces) distribution of charged groups is expected to influence charge compensation and, thus, the adsorption behavior.

Pinene-Based Oxidative Synthetic Toolbox for Scalable Polyester Synthesis.

Generation of renewable polymers is a long-standing goal toward reaching a more sustainable society, but building blocks in biomass can be incompatible with desired polymerization type, hampering the full implementation potential of biomaterials. Herein, we show how conceptually simple oxidative transformations can be used to unlock the inherent reactivity of terpene synthons in generating polyesters by two different mechanisms starting from the same α-pinene substrate. In the first pathway, α-pinene was oxidized into the bicyclic verbanone-based lactone and subsequently polymerized into star-shaped polymers via ring-opening polymerization, resulting in a biobased semicrystalline polyester with tunable glass transition and melting temperatures.

UV-Curable Bio-Based Polymers Derived from Industrial Pulp and Paper Processes.

Bio-based monomers represent the future market for polymer chemistry, since the political economics of different states promote green ventures toward more sustainable materials and processes. Industrial pulp and paper processing represent a large market that could advance the use of by-products to avoid waste production and reduce pollution. Lignin represents the most available side product that can be used to produce a bio-based monomer.

Synergetic Effect of Water-Soluble PEG-Based Macromonomers and Cellulose Nanocrystals for the Stabilization of PMMA Latexes by Surfactant-Free Emulsion Polymerization.

The combination of cellulose nanocrystals (CNCs) and poly(ethylene glycol) methyl ether methacrylate (PEGMA) was evaluated to synthesize stable latexes by surfactant-free emulsion polymerization of methyl methacrylate (MMA). Cellulose-particle interaction was provided due to the dual role of PEGMA, acting as water-soluble comonomer with MMA under emulsion polymerization conditions and able to interact with CNCs, recovered from sulfuric acid hydrolysis (HSO-CNCs). After preliminary experiments designed to validate the affinity between CNCs and PEG-stabilized PMMA particles obtained by MMA/PEGMA emulsion copolymerization, the effect of the PEGMA content and molar mass and also of the content of CNCs on the kinetics of the polymerization and the stability of the latexes were investigated.

Molecular Engineering of the Cellulose-Poly(Caprolactone) Bio-Nanocomposite Interface by Reactive Amphiphilic Copolymer Nanoparticles.

A molecularly engineered water-borne reactive compatibilizer is designed for tuning of the interface in melt-processed thermoplastic poly(caprolactone) (PCL)-cellulose nanocomposites. The mechanical properties of the nanocomposites are studied by tensile testing and dynamic mechanical analysis. The reactive compatibilizer is a statistical copolymer of 2-(dimethylamino)ethyl methacrylate and 2-hydroxy methacrylate, which is subsequently esterified and quaternized.

Characterization of Reduced and Surface-Modified Graphene Oxide in Poly(Ethylene--Butyl Acrylate) Composites for Electrical Applications.

Promising electrical field grading materials (FGMs) for high-voltage direct-current (HVDC) applications have been designed by dispersing reduced graphene oxide (rGO) grafted with relatively short chains of poly (-butyl methacrylate) (PBMA) in a poly(ethylene--butyl acrylate) (EBA) matrix. All rGO-PBMA composites with a filler fraction above 3 vol.% exhibited a distinct non-linear resistivity with increasing electric field; and it was confirmed that the resistivity could be tailored by changing the PBMA graft length or the rGO filler fraction.

All-Aqueous SI-ARGET ATRP from Cellulose Nanofibrils Using Hydrophilic and Hydrophobic Monomers.

An all-water-based procedure for "controlled" polymer grafting from cellulose nanofibrils is reported. Polymers and copolymers of poly(ethylene glycol) methyl ether methacrylate (POEGMA) and poly(methyl methacrylate) (PMMA) were synthesized by surface-initiated activators regenerated by electron transfer atom transfer radical polymerization (SI-ARGET ATRP) from the cellulose nanofibril (CNF) surface in water. A macroinitiator was electrostatically immobilized to the CNF surface, and its amphiphilic nature enabled polymerizations of both hydrophobic and hydrophilic monomers in water.

A Retro-biosynthesis-Based Route to Generate Pinene-Derived Polyesters.

Significantly increased production of biobased polymers is a prerequisite to replace petroleum-based materials towards reaching a circular bioeconomy. However, many renewable building blocks from wood and other plant material are not directly amenable for polymerization, due to their inert backbones and/or lack of functional group compatibility with the desired polymerization type. Based on a retro-biosynthetic analysis of polyesters, a chemoenzymatic route from (-)-α-pinene towards a verbanone-based lactone, which is further used in ring-opening polymerization, is presented.

Enzymatically Synthesized Vinyl Ether-Disulfide Monomer Enabling an Orthogonal Combination of Free Radical and Cationic Chemistry toward Sustainable Functional Networks.

This work demonstrates a versatile and environmentally friendly route for the development of new orthogonal monomers that can be used for postfunctionalizable polymer networks. A monomer containing both vinyl ether (VE) and cyclic disulfide moieties was synthesized via enzyme catalysis under benign reaction conditions. The bifunctional monomer could be polymerized to form macromolecues with differing architectures by the use of either cationic or radical photo polymerization.

Novel sustainable synthesis of vinyl ether ester building blocks, directly from carboxylic acids and the corresponding hydroxyl vinyl ether, and their photopolymerization.

Increased environmental awareness has led to a demand for sustainable, bio-based materials. Consequently, the development of new benign synthesis pathways utilizing a minimum of reaction steps and available bio-based building blocks is needed. In the present study, vinyl ether alcohols and functional carboxylic acids were used to synthesize bifunctional vinyl ether esters using the immobilized enzyme lipase B as a catalyst.

Insights into the EDC-mediated PEGylation of cellulose nanofibrils and their colloidal stability.

EDC-mediated coupling has frequently been utilized to poly(ethylene glycol) functionalize (PEGylate) cellulose-based materials, but no work has previously been reported on the direct N-(3-dimethylaminopropyl)-N-ethylcarbodiimide (EDC)-mediated PEGylation of cellulose nanofibrils (CNF). Herein, we report the first study where CNF has been directly sterically stabilized with amine-terminated PEG employing N-hydroxysuccinimide (NHS)-assisted EDC-coupling. This work has shown that this coupling reaction is highly sensitive to the reaction conditions and purification procedures, and hence an optimized coupling protocol was developed in order to achieve a reaction yield.

Polycaprolactone Nanocomposites Reinforced with Cellulose Nanocrystals Surface-Modified via Covalent Grafting or Physisorption: A Comparative Study.

In the present work, cellulose nanocrystals (CNCs) have been surface-modified either via covalent grafting or through physisorption of poly(n-butyl methacrylate) (PBMA) and employed as reinforcement in PCL. Covalent grafting was achieved by surface-initiated atom transfer radical polymerization (SI-ATRP). Two approaches were utilized for the physisorption: using either micelles of poly(dimethyl aminoethyl methacrylate)-block-poly(n-butyl methacrylate) (PDMAEMA-b-PBMA) or latex nanoparticles of poly(dimethyl aminoethyl methacrylate-co-methacrylic acid)-block-poly(n-butyl methacrylate) (P(DMAEMA-co-MAA)-b-PBMA).

Reduced and Surface-Modified Graphene Oxide with Nonlinear Resistivity.

Field-grading materials (FGMs) are used to reduce the probability for electrical breakdowns in critical regions of electrical components and are therefore of great importance. Usually, FGMs are heavily filled (40 vol.%) with semi-conducting or conducting particles.

Correction: Hydrophobic matrix-free graphene-oxide composites with isotropic and nematic states.

Correction for 'Hydrophobic matrix-free graphene-oxide composites with isotropic and nematic states' by Martin Wåhlander, et al., Nanoscale, 2016, DOI: 10.1039/c6nr01502f.

Hydrophobic matrix-free graphene-oxide composites with isotropic and nematic states.

We demonstrate a novel route to synthesise hydrophobic matrix-free composites of polymer-grafted graphene oxide (GO) showing isotropic or nematic alignment and shape-memory effects. For the first time, a cationic macroinitiator (MI) has been immobilised on anionic GO and subsequently grafted with hydrophobic polymer grafts. Dense grafts of PBA, PBMA and PMMA with a wide range of average graft lengths (MW: 1-440 kDa) were polymerised by surface-initiated controlled radical precipitation polymerisation from the statistical MI.

Xyloglucan-Functional Latex Particles via RAFT-Mediated Emulsion Polymerization for the Biomimetic Modification of Cellulose.

Herein, we report a novel class of latex particles composed of a hemicellulose, xyloglucan (XG), and poly(methyl methacrylate) (PMMA), specially designed to enable a biomimetic modification of cellulose. The formation of the latex particles was achieved utilizing reversible addition-fragmentation chain transfer (RAFT) mediated surfactant-free emulsion polymerization employing XG as a hydrophilic macromolecular RAFT agent (macroRAFT). In an initial step, XG was functionalized at the reducing chain end to bear a dithioester.

Novel Nanocomposites of Poly(lauryl methacrylate)-Grafted Al2O3 Nanoparticles in LDPE.

Aluminum oxide nanoparticles (NPs) were surface-modified by poly(lauryl methacrylate) (PLMA) using surface-initiated atom-transfer radical polymerization (SI-ATRP) of lauryl methacrylate. Nanocomposites were obtained by mixing the grafted NPs in a low-density polyethylene (LDPE) matrix in different ratios. First, the NPs were silanized with different aminosilanes, (3-aminopropyl)triethoxysilane, and 3-aminopropyl(diethoxy)methylsilane (APDMS).

Histamine-functionalized copolymer micelles as a drug delivery system in 2D and 3D models of breast cancer.

Histamine functionalized block copolymers based on poly(allyl glycidyl ether)--poly(ethylene oxide) (PAGE--PEO) were prepared with different ratios of histamine and octyl or benzyl groups using UV-initiated thiol-ene click chemistry. At neutral pH, the histamine units are uncharged and hydrophobic, while in acidic environments, such as in the endosome, lysosomes, or extracellular sites of tumours, the histamine groups are positively charged and hydrophilic. pH responsible polymer drug delivery systems is a promising route to site specific delivery of drugs and offers the potential to avoid side effects of systemic treatment.

Disulfide-Functionalized Unimolecular Micelles as Selective Redox-Responsive Nanocarriers.

Redox-sensitive hyperbranched dendritic-linear polymers (HBDLPs) were prepared and stabilized individually as unimolecular micelles with diameters in the range 25-40 nm. The high molecular weight (500-950 kDa), core-shell amphiphilic structures were synthesized through a combination of self-condensing vinyl copolymerization (SCVCP) and atom transfer radical polymerization (ATRP). Cleavable disulfide bonds were introduced, either in the backbone, or in pendant groups, of the hyperbranched core of the HBDLPs.

Preparation and characterization of functionalized cellulose nanocrystals.

In this work, a series of functional nanocrystals (F-CNCs) was successfully produced by an efficient preparation method, combining acid hydrolysis and Fischer esterification with various organic acids. Functionalities such as ATRP initiators, double bonds, triple bonds, and thiols could be incorporated on CNCs. Surface modification was confirmed by FT-IR, XPS, and elemental analysis.

Toward unimolecular micelles with tunable dimensions using hyperbranched dendritic-linear polymers.

A library of amphiphilic, hyperbranched dendritic-linear polymers (HBDLPs) are successfully synthesized, and evaluated as potential unimolecular micelles. Hyperbranched macroinitiators (HBMI), extended with poly(ethylene glycol) methacrylate (P(OEGMA)), are afforded via a combination of self-condensing vinyl (co)polymerization (SCV(C)P) and atom transfer radical polymerization (ATRP), providing a versatile two-step synthetic route. The HBDLP architecture and chain lengths are varied, and the effect on the nanoparticle (NP) stability and properties are evaluated.