MXene Clay (Ti2C)-Containing In Situ Polymerized Hollow Core-Shell Binder for Silicon-Based Anodes in Lithium-Ion Batteries.

Silicon, an attractive anode material, suffers fast capacity fading due to the electrical isolation from massive volumetric expansion upon cycling. However, it holds a high theoretical capacity and low operation voltage in its practical application. In this study, a new water-based binder, MXene clay/hollow core-shell acrylate composite, was synthesized through an in situ emulsion polymerization technique to alleviate the fast capacity fading of the silicon anode efficiently.

Sulfonation of alginate grafted with polyacrylamide as a potential binder for high-capacity Si/C anodes.

A systematic approach for how to find an appropriate polymer binder for high-capacity LIB anodes is presented in this study. As an example, a newly-developed SAlg--PAAm binder, alginate functionalized with sulfo groups and subsequently grafted with polyacrylamide, is used for the Si/C electrode. Various characteristics of the binder polymer itself, two basic characteristics of the electrode with respect to the binder, and the effect of the binder on cell performance are subsequently investigated.

Minimizing two-dimensional TiCT MXene nanosheet loading in carbon-free silicon anodes.

Silicon anodes are promising for high energy batteries because of their excellent theoretical gravimetric capacity (3579 mA h g-1). However, silicon's large volume expansion and poor conductivity hinder its practical application; thus, binders and conductive additives are added, effectively diluting the active silicon material. To address this issue, reports of 2D MXene nanosheets have emerged as additives for silicon anodes, but many of these reports use high MXene compositions of 22-66 wt%, still presenting the issue of diluting the active silicon material.

In situ synthesis and cell performance of a Si/C core-shell/ball-milled graphite composite for lithium ion batteries.

A high-capacity silicon-carbon core-shell (Si/C) supported by ball-milled graphite (BMG) was synthesized in situ using a hydrosilylation reaction and tested as an anode material for lithium ion batteries (LIBs) in the investigation of the effects of dual buffer layers of carbon shell and BMG. The Si/C/BMG sample effectively absorbed high volumetric expansion/contraction generated during charge/discharge process due to the assistance of dual elastic buffers of carbon shell and BMG. As a result, after 50 charge/discharge cycles, the Si/C/BMG electrodes still had a very high capacity of 1615 mAh/g, whereas raw Si, Si/C, and a mechanical mixture of Si/C and BMG were less than 500 mAh/g.

Performance enhancement of polymer electrolyte membrane fuel cells by dual-layered membrane electrode assembly structures with carbon nanotubes.

The effect of dual-layered membrane electrode assemblies (d-MEAs) on the performance of a polymer electrolyte membrane fuel cell (PEMFC) was investigated using the following characterization techniques: single cell performance test, electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV). It has been shown that the PEMFC with d-MEAs has better cell performance than that with typical mono-layered MEAs (m-MEAs). In particular, the d-MEA whose inner layer is composed of multi-walled carbon nanotubes (MWCNTs) showed the best fuel cell performance.

SnO2 nanoparticles distributed on multi-walled carbon nanotubes and ball-milled graphite as anode materials of lithium ion batteries.

SnO2 nanoparticles were supported on ball-milled graphite (BMG) or carbon nanotubes (CNTs) using a chemical reduction method with ethylene glycol, and the electrochemical properties of the nanocomposites were evaluated as anode active materials of lithium-ion batteries. The BMG and CNTs contributed to an increase in both the capacity enhancement and cyclic stability compared to that of commercial graphite. In particular, the mixture electrode of SnO2/BMG:SnO2/CNT = 3:1 (in weight ratio) showed higher performance in the reversible capacity and cyclic stability than did the SnO2/BMG and SnO2/CNT electrodes.

Preparation of nano-sized graphite-supported CuO and Cu-Sn as active materials in lithium ion batteries.

Nano-sized Cu-Sn and Cu oxide particles supported on ball-milled graphite were synthesized, and their electrochemical characteristics for use as anode active materials in lithium-ion batteries were investigated. The samples were also characterized via FE-SEM, XRD, and TGA. Most of the Cu oxides on BMG were monoclinic CuO crystals, whereas the Cu-Sn particles were composed of hexagonal Cu3Sn and tetragonal SnO2 crystals.

Reassembled graphene-platelets encapsulated silicon nanoparticles for Li-ion battery anodes.

Among lithium alloy metals, silicon is an attractive candidate to replace commercial graphite anode because silicon possesses about ten times higher theoretical energy density than graphite. However, electrically nonconducting silicon undergoes a large volume changes during lithiation/delithiation reactions, which causes fast loss of storage capacity upon cycling due to electrode pulverization. To alleviate these problems, electrodes comprising Si nanoparticles (20 nm) and graphene platelets, denoted as SiGP-1 (Si = 35.