3D Temperature-Controlled Interchangeable Pattern for Size-Selective Nanoparticle Capture.

Patterned surfaces with distinct regularity and structured arrangements have attracted great interest due to their extensive promising applications. Although colloidal patterning has conventionally been used to create such surfaces, herein, we introduce a novel 3D patterned poly(isopropylacrylamide) (PNIPAM) surface, synthesized by using a combination of colloidal templating and surface-initiated photoinduced electron transfer-reversible addition-fragmentation chain transfer (SI-PET-RAFT) polymerization. In order to investigate the temperature-driven 3D morphological variations at a lower critical solution temperature (LCST) of ∼32 °C, multifaceted characterization techniques were employed.

Cellulose nanocrystals-reinforced waterborne epoxy coatings with enhanced corrosion resistance for steel.

The practical applications of waterborne epoxy coatings are limited due to their poor barrier properties caused by the formation of numerous micropores and defects during the curing process. Herein, cellulose nanocrystals (CNCs)-reinforced waterborne epoxy coatings were fabricated by the direct addition of 0.2-1.

Synthesis of hyperbranched polymer films via electrodeposition and oxygen-tolerant surface-initiated photoinduced polymerization.

Hypothesis: Hyperbranched polymers, not only possess higher functionality, but are also easier to prepare compared to dendrimers and dendric polymers. Combining electrodeposition and surface-initiated photoinduced electron transfer-reversible addition-fragmentation chain transfer (SI-PET-RAFT) polymerization is hypothesized to be a novel strategy for preparing hyperbranched polymer films on conductive surfaces without degassing.

Experiments: Polymer brush grafted films with four different architectures (i.

Anticorrosive epoxy coatings from direct epoxidation of bioethanol fractionated lignin.

The development of lignin-based anticorrosive epoxy coatings for steel protection is beneficial for both alleviating the fossil resource depletion and value-added utilization of lignin but remains a challenge due to the inherent heterogeneous structure of lignin. Here, we selectively extract the low molecular weight (MW) fraction of a crop residue-derived enzymatic hydrolysis lignin (EHL) through a bioethanol fractionation process and prepare epoxy resin by direct epoxidation of the bioethanol fractionated lignin (BFL). The coatings are then fabricated using 20-100 wt% of BFL-based epoxy resin (LEp) as the commercial epoxy resin substitute.

On the Interfacial Behavior of Catenated Poly(l-lactide) at the Air-Water Interface.

Interfacial properties of polymeric materials are significantly influenced by their architectural structures and spatial features, while such a study of topologically interesting macromolecules is rarely reported. In this work, we reported, for the first time, the interfacial behavior of catenated poly(l-lactide) (C-PLA) at the air-water interface and compared it with its linear analogue (L-PLA). The isotherms of surface pressure-area per repeating unit showed significant interfacial behavioral differences between the two polymers with different topologies.

Additively manufactured high-performance polymeric materials and their potential use in the oil and gas industry.

The oil and gas industry has been tagged as among the largest revenue-generating sectors in the world. High-performance polymers (HPPs), on the other hand, are among the most useful industrial materials, while the utility of 3D printing technologies has evolved and transitioned from rapid prototyping of composite materials to manufacturing of functional parts. In this prospective, we highlight the potential uses and industrial applications of 3D-printed HPP materials in the oil and gas sector, including the challenges and opportunities present.

Electropolymerized-molecularly imprinted polymers (E-MIPS) as sensing elements for the detection of dengue infection.

A straightforward in situ detection method for dengue infection was demonstrated through the molecular imprinting of a dengue nonstructural protein 1 (NS1) epitope into an electropolymerized molecularly imprinted polyterthiophene (E-MIP) film sensor. The key enabling step in the sensor fabrication is based on an epitope imprinting strategy, in which short peptide sequences derived from the original target molecules were employed as the main template for detection and analysis. The formation of the E-MIP sensor films was facilitated using cyclic voltammetry (CV) and monitored in situ by electrochemical quartz crystal microbalance (EC-QCM).

On the progress of 3D-printed hydrogels for tissue engineering.

Abstract: Additive manufacturing or more commonly known as 3D printing, is currently driving innovations and applications in diverse fields such as prototyping, manufacturing, aerospace, education, and medicine. Recent technological and materials research breakthroughs have enabled 3D bioprinting, where biomaterials and cells are used to create scaffolds and functional living tissues (e.g.

3D printing of biomedically relevant polymer materials and biocompatibility.

Abstract: Research on polymer materials for additive manufacturing technology in biomedical applications is as promising as it is numerous, but biocompatibility of printable materials still remains a big challenge. Changes occurring during the 3D-printing processes itself may have adverse effects on the compatibility of the completed print. This prospective will put emphasis on the different additives and processes that can have a direct impact on biocompatibility during and after 3D printing of polymer materials.

Ring-Forming Polymerization toward Perfluorocyclobutyl and -Diynylarene-Derived Materials: From Synthesis to Practical Applications.

Many desirable characteristics of polymers arise from the method of polymerization and structural features of their repeat units, which typically are responsible for the polymer's performance at the cost of processability. While linear alternatives are popular, polymers composed of cyclic repeat units across their backbones have generally been shown to exhibit higher optical transparency, lower water absorption, and higher glass transition temperatures. These specifically include polymers built with either substituted alicyclic structures or aromatic rings, or both.