Angiotensin-(1-7) decreases inflammation and lung damage caused by betacoronavirus infection in mice.

Objective: Pro-resolving molecules, including the peptide Angiotensin-(1-7) [Ang-(1-7)], have potential adjunctive therapy for infections. Here we evaluate the actions of Ang-(1-7) in betacoronavirus infection in mice.

Methods: C57BL/6J mice were infected intranasally with the murine betacoronavirus MHV-3 and K18-hACE2 mice were infected with SARS-CoV-2.

The angiotensin-(1-7)/MasR axis improves pneumonia caused by Pseudomonas aeruginosa: Extending the therapeutic window for antibiotic therapy.

Pseudomonas aeruginosa is a frequent cause of antimicrobial-resistant hospital-acquired pneumonia, especially in critically ill patients. Inflammation triggered by P. aeruginosa infection is necessary for bacterial clearance but must be spatially and temporally regulated to prevent further tissue damage and bacterial dissemination.

Treatment of a Soft Tissue Depression with a Xenograft Bone Substitute at the Second Stage of an Implant Procedure: A Case Report.

Following the extraction of a compromised tooth, the edentulous alveolar ridge undergoes physiologic bone remodeling, which may create a bone volume too deficient for implant placement. Guided bone regeneration (GBR) provides a predictable treatment option to increase the alveolar bone volume for implant placement, but a soft or hard tissue deficiency may remain even after this augmentation procedure has been completed. These deficiencies can be especially challenging in the esthetic zone, where patient expectations and esthetics often determine the satisfaction of the treatment outcome.

Assembly and use of a low-cost paracentesis simulator for the teaching of puncture and drainage of ascites.

Objectives: to describe the assembly of a low-cost paracentesis simulator and evaluate its effectiveness, acceptance and impact on the learning of medical students.

Methodology: a paracentesis simulator was built using a mannequin and materials such as plastic bottles, Velcro, polyvinyl chloride sheets and silicone were used. A cross-sectional and experimental study was carried out with undergraduate medical students without previous practical experience with paracentesis, which sought to validate the model, evaluating its benefits in learning and obtaining technical skills.

Effect of processing methods on the chipping resistance of veneered zirconia.

Objectives: To evaluate the edge chipping resistance (R) and the fracture toughness (K) of 3Y-TZP bilayers produced with the following materials/processing combinations: fluorapatite glass-ceramic applied on zirconia using the traditional layering and hot-pressing (press-on) techniques; feldspathic porcelain using rapid layer technology (RLT); and lithium disilicate glass-ceramic using CAD-on method. The influence of the cooling rate (slow and fast) was analyzed for layering and hot-pressing.

Methods: Bilayer bars (25x4x2 mm) were made following manufacturers' instructions.

Aging resistant ZTA composite for dental applications: Microstructural, optical and mechanical characterization.

Objective: To synthesize a zirconia toughened alumina (ZTA) composite with 70% alumina reinforced by 30% zirconia for dental applications and to characterize its microstructure and optical properties for comparison with the isolated counterpart materials and a first-generation 3Y-TZP.

Methods: Disc-shaped specimens were divided in four groups (n = 70/material): (1) 3YSB-E (first generation 3Y-TZP), (2) Zpex (second generation 3Y-TZP), (3) alumina, and (4) ZTA-Zpex 70/30. After synthesis, ceramic powders were pressed, and green-body samples sintered following a predetermined protocol.

Dental ceramics: a review of new materials and processing methods.

The evolution of computerized systems for the production of dental restorations associated to the development of novel microstructures for ceramic materials has caused an important change in the clinical workflow for dentists and technicians, as well as in the treatment options offered to patients. New microstructures have also been developed by the industry in order to offer ceramic and composite materials with optimized properties, i.e.

Influence of Resin Cements on Color Stability of Different Ceramic Systems.

The purpose of this study was to evaluate color stability of two dental ceramics cemented with two resin cements, assessing the color difference (ΔE00) by the measurement of L*, a*, b*, c* and h* of transmittance. The combination of two ceramic system (feldspathic and lithium disilicate) and two resin cements - color A3 (RelyX ARC and Variolink II) resulted in 4 groups (n=5). Ten disks-shaped specimens were fabricated for each ceramic system (10x1.

Synthesis and characterization of silver phosphate/calcium phosphate mixed particles capable of silver nanoparticle formation by photoreduction.

Silver phosphate is a semi-conductor sensitive to UV-Vis radiation (<530nm). Exposure to radiation removes electrons from the oxygen valence shell, which are scavenged by silver cations (Ag), forming metallic silver (Ag) nanoparticles. The possibility of silver nanoparticle formation in situ by a photoreduction process was the basis for the application of mixed calcium phosphate/silver phosphate particles as remineralizing and antibacterial fillers in resin-based dental materials.

Influence of resin cement shade on the color and translucency of ceramic veneers.

Objective: This in vitro study evaluated the effect of two different shades of resin cement (RC- A1 and A3) layer on color change, translucency parameter (TP), and chroma of low (LT) and high (HT) translucent reinforced lithium disilicate ceramic laminates.

Material And Methods: One dual-cured RC (Variolink II, A1- and A3-shade, Ivoclar Vivadent) was applied to 1-mm thick ceramic discs to create thin RC films (100 µm thick) under the ceramics. The RC was exposed to light from a LED curing unit.

The effect of preheating and opacity on the sorption and solubility of a composite resin.

This study evaluated the influence of material opacity and preheating on the sorption and solubility of a composite resin material. A commercially available composite resin and an 8 × 2-mm circular metallic matrix were used to fabricate a total of 60 specimens in 6 shades, of which 3 had conventional opacity (CA2, CA3, and CA3.5) and 3 were opaque (OA2, OA3, and OA3.

Flexural strength and failure modes of layered ceramic structures.

Objective: To evaluate the effect of the specimen design on the flexural strength (σ(f)) and failure mode of ceramic structures, testing the hypothesis that the ceramic material under tension controls the mechanical performance of the structure.

Methods: Three ceramics used as framework materials for fixed partial dentures (YZ--Vita In-Ceram YZ; IZ--Vita In-Ceram Zirconia; AL--Vita In-Ceram AL) and two veneering porcelains (VM7 and VM9) were studied. Bar-shaped specimens were produced in three different designs (n=10): monolithic, two layers (porcelain-framework) and three layers (TRI) (porcelain-framework-porcelain).