Evolution and New Generation of Dual Mobility Cups.

Although total hip arthroplasty (THA) is considered a successful procedure, hip dislocation remains the main cause of early failure. Dual mobility cups (DMCs) have been shown to significantly reduce the dislocation rate in both primary and revision THAs. During the past several decades, DMCs have evolved in design and fixation interface.

Modular dual mobility articulation in primary and revision hip arthroplasty: lights and shadows.

Purpose: The use of dual mobility cups in total hip arthroplasty has gained popularity in light of the fact it enables to reduce dislocation through increased jumping distance (JD) and impingement-free arc of movement. Modular Dual Mobility Cup (modular DMC) systems have been recently introduced to enable the use of dual mobility cups with standard metal-backed shells. The objective of this study was twofold: calculate the JD for each modular DMC system and conduct a systematic literature review to report clinical outcomes and reasons for failure of this construct.

Use of dual-mobility cup in primary total hip arthroplasties: an Italian regional register (RIPO) study on three thousand, seven hundred and ten cases.

Purpose: The purpose of the study was to investigate the outcome of dual-mobility cup (DM) compared with a standard cup (SC) in primary total hip arthroplasty (THA) in the long-term follow-up based on a regional Italian joint registry (RIPO).

Methods: The Registry of Prosthetic Orthopaedic Implant (RIPO) was consulted, looking for all primary THAs implanted from 2000 to 2019. Three thousand seven hundred ten were dual-mobility cup (DM) total hip arthroplasties (THA) and 85.

Dual mobility cup in hip arthroplasty: An in-depth analysis of joint registries.

Although total hip arthroplasty (THA) has shown successful results, instability remains a major complication. In recent years, dual mobility cups (DMC) have gained interest among clinicians thanks to its low rate of dislocation and good clinical results. The main aim of this work was to describe the accuracy of data on DMC from national and regional joint registries (JRs) and the available worldwide literature.

Revision of a Monoblock Metal-on-Metal Cup Using a Dual Mobility Component: Is It a Reasonable Option?

Revision of large-diameter, monoblock acetabular components for both hip resurfacing arthroplasty and metal-on-metal (MoM) total hip arthroplasty (THA) is correlated to a high amount of complications. For this reason, performing a limited revision by conversion to a dual mobility (DM) without acetabular component exchange has been proposed in order to limit these complications. Although DM bearing offers an easy solution avoiding the intraoperative and time-associated complications, concern about polyethylene wear and stability remains due to the difference regarding the design, the coverage angle and the clearance of the two implants.

Progression of osteoarthritis and reoperation in unicompartmental knee arthroplasty: A comparison of national joint registries.

Unicompartmental knee arthroplasty remains a challenge for orthopaedic surgeons because of its higher revision rate compare with the total knee arthroplasty. The hypothesis of this work is that the progression of osteoarthritis in unicompartmental knee prostheses is the natural history of the degenerative disease and a reason for reoperation. Most international joint registries consider this fact as a failure of the implant and a cause of revision.

Efficacy of triamcinolone acetate and methylprednisolone acetonide for intrabursal injection after ultrasound-guided percutaneous treatment in painful shoulder calcific tendonitis: a randomized controlled trial.

Background Ultrasound-guided percutaneous irrigation of calcific tendinopathy (US-PICT) with intrabursal steroid injection is an elective treatment for painful rotator cuff calcific tendinopathy. Purpose To compare the efficacy of post-US-PICT intrabursal 40 mg injection of triamcinolone acetonide (TA) versus methylprednisolone acetate (MA). Material and Methods Forty patients (22 women; mean age 48.

Combined effect of the body mass index and implant size on the wear of retrieved total knee prostheses.

Total Knee Arthroplasty is a well-established surgical procedure performed to relieve pain and to restore function in knee osteoarthritis. A proper choice of the implant size is mandatory in order to guarantee the success of the implant and to respect the bone stock of tibial plateau and femoral condyles. The aim of this study was to investigate the combined effect of Body Mass Index and implant size on the wear damage of retrieved knee implants, a still debated subject.

Treatment of osteoid osteoma of the elbow by radiofrequency thermal ablation.

Background: This article presents the experience at the Rizzoli Orthopaedic Institute in the treatment of intracapsular osteoid osteoma (OO) of the elbow by computed tomography-guided percutaneous radiofrequency thermal ablation (RFA).

Materials And Methods: Our team performed more than 800 RFA procedures to treat OO up to 2010. In 27 cases, the lesion site was the articular area of the elbow (humerus in 13 cases, ulna in 13, and radius in 1).

Mobile-bearing total knee arthroplasty: a full traumatic rotation of 180°.

From February 2008 to September 2012 we implanted 204 mobile-bearing knee prostheses in 192 patients. All the prostheses were cemented (both femoral and tibial components), and the patella was not replaced. Only one early complication of the implants (1/204 = 0.

Acetabular transverse nonunion treated by a hemispherical press-fit cup and structural autologous bone graft.

Nonunion of acetabular fractures are uncommon, and their treatment can be a rather demanding procedure. Acute total hip arthroplasty could be a possible treatment choice, especially when there is a femoral head arthritis. We report a case of transverse acetabular fracture nonunion treated by a cementless hemispherical press-fit cup and autologous structural bone graft.