Single-Step Deposition of Chalcopyrite (CuFeS) Thin Films.

Thin films of chalcopyrite, CuFeS, are promising candidates for use as absorber layers in photovoltaic cells due to their low band gap and high absorbance. These films are typically deposited in two or three steps, always involving an annealing process. In this work, the CuFeS film was deposited on a glass substrate in a single deposition step using the cathodic cylindrical plasma deposition (CCyPD) technique.

Repurposing ABS to Produce Polyamide 6 (PA6)-Based Blends: Reactive Compatibilization with SAN-g-MA of a High Degree of Functionalization.

In this study, recycled acrylonitrile-butadiene-styrene terpolymer (ABSr) was reused to produce polyamide 6 (PA6)-based blends. This was achieved through reactive compatibilization using styrene-acrylonitrile-maleic anhydride (SAN-g-MA) copolymer with a high degree of functionalization (6-10% MA). The PA6/ABSr and PA6/ABSr/SAN-g-MA blends were prepared through melt processing and injection molding and then analyzed for their rheological, mechanical, thermomechanical, thermal, and structural properties, as well as morphology.

From Waste to Styrene-Butadiene (SBR) Reuse: Developing PP/SBR/SEP Mixtures with Carbon Nanotubes for Antistatic Application.

Styrene-butadiene rubber (SBR) waste from the shoe industry was repurposed to produce polypropylene (PP)-based compounds, with the aim of evaluating their antistatic potential. Styrene-ethylene-propylene (SEP) was added as a compatibilizing agent, while carbon nanotubes (MWCNT) were incorporated as a conductive nanofiller. The polymer compounds were processed in an internal mixer, and injection molded.

Toward Producing Biopolyethylene/Babassu Fiber Biocomposites with Improved Mechanical and Thermomechanical Properties.

The development of polymeric biocomposites containing natural fibers has grown over the years due to the properties achieved and its eco-friendly nature. Thus, biocomposites involving a polymer from a renewable source (Biopolyethylene (BioPE)) and babassu fibers (BFs), compatibilized with polyethylene grafted with maleic anhydride (MA) and acrylic acid (AA) (PE-g-MA and PE-g-AA, respectively) were obtained using melt mixing and injection molded into tensile, impact, and HDT specimens. Babassu fiber was characterized with Fourier transform infrared spectroscopy (FTIR), thermogravimetry (TGA), and scanning electron microscopy (SEM).

Toward the Improvement of Maleic Anhydride Functionalization in Polyhydroxybutyrate (PHB): Effect of Styrene Monomer and Sn(Oct) Catalyst.

In this work, polyhydroxybutyrate (PHB) was maleic anhydride (MA)-grafted in the molten state, using dicumyl peroxide (DCP) as a reaction initiator. Tin(II) 2-ethylhexanoate (Sn(Oct)) and styrene monomer (St.) were used to maximize the maleic anhydride grafting degree.

Tailoring PLA/ABS Blends Compatibilized with SEBS-g-MA through Annealing Heat Treatment.

In this work, blends based on poly (lactic acid) (PLA)/acrylonitrile-butadiene-styrene (ABS) compatibilized with maleic anhydride-grafted (SEBS-g-MA) were prepared in a co-rotational twin-screw extruder by varying the concentrations of the compatibilizing agent. The influence of the compatibilizing agent on the morphology, mechanical, thermal, thermomechanical, and rheological properties of the prepared materials was analyzed. The effect of annealing on the properties of the blends was also investigated using injection-molded samples.

Tailoring Nylon 6/Acrylonitrile-Butadiene-Styrene Nanocomposites for Application against Electromagnetic Interference: Evaluation of the Mechanical, Thermal and Electrical Behavior, and the Electromagnetic Shielding Efficiency.

Nylon 6/acrylonitrile-butadiene-styrene nanocomposites were prepared by mixing in a molten state and injection molded for application in electromagnetic interference shielding and antistatic packaging. Multi-wall carbon nanotubes (MWCNT) and maleic anhydride-grafted ABS compatibilizer were incorporated to improve the electrical conductivity and mechanical performance. The nanocomposites were characterized by oscillatory rheology, Izod impact strength, tensile strength, thermogravimetry, current-voltage measurements, shielding against electromagnetic interference, and scanning electron microscopy.

Influence of Small Amounts of ABS and ABS-MA on PA6 Properties: Evaluation of Torque Rheometry, Mechanical, Thermomechanical, Thermal, Morphological, and Water Absorption Kinetics Characteristics.

In this work, polyamide 6 (PA6) properties were tailored and improved using a maleic anhydride-grafted acrylonitrile-butadiene-styrene terpolymer (ABS-MA). The PA6/ABS-MA blends were prepared using a co-rotational twin-screw extruder. Subsequently, the extruded pellets were injection-molded.

Tailoring Poly(lactic acid) (PLA) Properties: Effect of the Impact Modifiers EE-g-GMA and POE-g-GMA.

Poly(ethylene-octene) grafted with glycidyl methacrylate (POE-g-GMA) and ethylene elastomeric grafted with glycidyl methacrylate (EE-g-GMA) were used as impact modifiers, aiming for tailoring poly(lactic acid) (PLA) properties. POE-g-GMA and EE-g-GMA was used in a proportion of 5; 7.5 and 10%, considering a good balance of properties for PLA.

The Effect of ZnO on the Failure of PET by Environmental Stress Cracking.

The aim of the present work is to evaluate the effect of NaOH solution as a stress cracking agent on the thermal and tensile properties of PET and PET/ZnO composites. The solutions were applied during tensile testing and the effects were monitored by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and testing the actual mechanical properties. The rate of crystallization was increased when the samples were exposed to NaOH, as observed by both cold and melt crystallization; this is possibly due to the reduction in molar mass of the PET molecules caused by NaOH.

Polyamide 6 Nanocomposites with Inorganic Particles Modified with Three Quaternary Ammonium Salts.

The purpose of this study was to obtain polyamide 6 nanocomposites with national organically modified clay with three quaternary ammonium salts. The obtained results confirm the intercalation of molecules of salt in the clay layers, and a good interaction with the polymer, showing the formation of intercalated and/or partially exfoliated structures. The nanocomposites showed similar thermal stability compared to pure polymer, and the mechanical properties presented interesting and promising results.