Compression-sensitive smart windows: inclined pores for dynamic transparency changes.

Smart windows, capable of tailoring light transmission, can significantly reduce energy consumption in building services. While mechano-responsive windows activated by strains are promising candidates, they face long-lasting challenges in which the space for the light scatterer's operation has to be enlarged along with the window size, undermining the practicality. Recent attempts to tackle this challenge inevitably generate side effects with compromised performance in light modulation.

Functional bio-inspired hybrid fliers with separated ring and leading edge vortices.

Recent advances in passive flying systems inspired by wind-dispersed seeds contribute to increasing interest in their use for remote sensing applications across large spatial domains in the Lagrangian frame of reference. These concepts create possibilities for developing and studying structures with performance characteristics and operating mechanisms that lie beyond those found in nature. Here, we demonstrate a hybrid flier system, fabricated through a process of controlled buckling, to yield unusual geometries optimized for flight.

Rational design of hybrid sensor arrays combined synergistically with machine learning for rapid response to a hazardous gas leak environment in chemical plants.

Combinations of semiconductor metal oxide (SMO) sensors, electrochemical (EC) sensors, and photoionization detection (PID) sensors were used to discriminate chemical hazards on the basis of machine learning. Sensing data inputs were exploited in the form of either numerical or image data formats, and the classification of chemical hazards with high accuracy was achieved in both cases. Even a small amount of gas sensing or purging data (input for ∼30 s) input can be exploited in machine-learning-based gas discrimination.

Investigation of Laser-Induced Graphene (LIG) on a Flexible Substrate and Its Functionalization by Metal Doping for Gas-Sensing Applications.

Graphene materials synthesized using direct laser writing (laser-induced graphene; LIG) make favorable sensor materials because of their large surface area, ease of fabrication, and cost-effectiveness. In particular, LIG decorated with metal nanoparticles (NPs) has been used in various sensors, including chemical sensors and electronic and electrochemical biosensors. However, the effect of metal decoration on LIG sensors remains controversial; hypotheses based on computational simulations do not always match the experimental results, and even the experimental results reported by different researchers have not been consistent.

Ultrasensitive biosensing platform for detection based on functionalized graphene devices.

Tuberculosis (TB) has high morbidity as a chronic infectious disease transmitted mainly through the respiratory tract. However, the conventional diagnosis methods for TB are time-consuming and require specialists, making the diagnosis of TB with point-of-care (POC) detection difficult. Here, we developed a graphene-based field-effect transistor (GFET) biosensor for detecting the MPT64 protein of with high sensitivity as a POC detection platform for TB.

Unusual Raman Enhancement Effect of Ultrathin Copper Sulfide.

In surface-enhanced Raman spectroscopy (SERS), 2D materials are explored as substrates owing to their chemical stability and reproducibility. However, they exhibit lower enhancement factors (EFs) compared to noble metal-based SERS substrates. This study demonstrates the application of ultrathin covellite copper sulfide (CuS) as a cost-effective SERS substrate with a high EF value of 7.

Enhanced Thermal Pad Composites Using Densely Aligned MgO Nanowires.

Owing to the increasing demand for the miniaturization and integration of electronic devices, thermal interface materials (TIMs) are crucial components for removing heat and improving the lifetime and safety of electronic devices. Among these, thermal pads are reusable alternatives to thermal paste-type TIMs; however, conventional thermal pads comprise a homogeneous polymer with low thermal conductivity. Composite materials of thermally conducting fillers and polymer matrices are considered suitable alternatives to high-performance pad materials owing to their controllable thermal properties.

Role of graphene quantum dots with discrete band gaps on SnO nanodomes for NO gas sensors with an ultralow detection limit.

NO is a major air pollutant that should be monitored due to its harmful effects on the environment and human health. Semiconducting metal oxide-based gas sensors have been widely explored owing to their superior sensitivity towards NO, but their high operating temperature (>200 °C) and low selectivity still limit their practical use in sensor devices. In this study, we decorated graphene quantum dots (GQDs) with discrete band gaps onto tin oxide nanodomes (GQD@SnO nanodomes), enabling room temperature (RT) sensing towards 5 ppm NO gas with a noticeable response ((/) - 1 = 4.

Ultrathin Metal Film on Graphene for Percolation-Threshold-Limited Thermal Emissivity Control.

Translucent Au/graphene hybrid films are shown to be effective in reducing thermal emission from the underlying surfaces when the deposition thickness of Au is close to the percolation threshold. The critical Au deposition thickness for an abrupt change in emissivity is reduced from 15 nm (Si substrate) to a percolation-threshold-limited thickness of 8.5 nm (graphene/Si substrate) because of the chemical inertness of graphene leading to the deposited Au atoms forming a thin, crystalline layer.

Responsive materials and mechanisms as thermal safety systems for skin-interfaced electronic devices.

Soft, wireless physiological sensors that gently adhere to the skin are capable of continuous clinical-grade health monitoring in hospital and/or home settings, of particular value to critically ill infants and other vulnerable patients, but they present risks for injury upon thermal failure. This paper introduces an active materials approach that automatically minimizes such risks, to complement traditional schemes that rely on integrated sensors and electronic control circuits. The strategy exploits thin, flexible bladders that contain small volumes of liquid with boiling points a few degrees above body temperature.

Multifunctional-high resolution imaging plate based on hydrophilic graphene for digital pathology.

In the present study, we showed that hydrophilic graphene can serve as an ideal imaging plate for biological specimens. Graphene being a single-atom-thick semi-metal with low secondary electron emission, array tomography analysis of serial sections of biological specimens on a graphene substrate showed excellent image quality with improved-axis resolution, without including any conductive surface coatings. However, the hydrophobic nature of graphene makes the placement of biological specimens difficult; graphene functionalized with polydimethylsiloxane oligomer was fabricated using a simple soft lithography technique and then processed with oxygen plasma to provide hydrophilic graphene with minimal damage to graphene.

Thermally switchable, crystallizable oil and silicone composite adhesives for skin-interfaced wearable devices.

Continuous health monitoring is essential for clinical care, especially for patients in neonatal and pediatric intensive care units. Monitoring currently requires wired biosensors affixed to the skin with strong adhesives that can cause irritation and iatrogenic injuries during removal. Emerging wireless alternatives are attractive, but requirements for skin adhesives remain.

Photolithographic realization of target nanostructures in 3D space by inverse design of phase modulation.

The mass production of precise three-dimensional (3D) nanopatterns has long been the ultimate goal of fabrication technology. While interference lithography and proximity-field nanopatterning (PnP) may provide partial solutions, their setup complexity and limited range of realizable structures, respectively, remain the main problems. Here, we tackle these challenges by applying an inverse design to the PnP process.

Rationally Designed TiO Nanostructures of Continuous Pore Network for Fast-Responding and Highly Sensitive Acetone Sensor.

For the last several years, indoor air quality monitoring has been a significant issue due to the increasing time portion of indoor human activities. Especially, the early detection of volatile organic compounds potentially harmful to the human body by the prolonged exposure is the primary concern for public human health, and such technology is imperatively desired. In this study, highly porous and periodic 3D TiO nanostructures are designed and studied for this concern.

Interdigitated Three-Dimensional Heterogeneous Nanocomposites for High-Performance Mechanochromic Smart Membranes.

Mechanochromic smart membranes capable of optical modulation have great potential in smart windows, artificial skins, and camouflage. However, the realization of high-contrast optical modulation based on light scattering activated at a low strain remains challenging. Here, we present a strategy for designing mechanochromic scattering membranes by introducing a Young's modulus mismatch between the two interdigitated polydimethylsiloxane phases with weak interfaces in a periodic three-dimensional (3D) structure.

A Skin-Interfaced, Miniaturized Microfluidic Analysis and Delivery System for Colorimetric Measurements of Nutrients in Sweat and Supply of Vitamins Through the Skin.

Nutrients play critical roles in maintaining core physiological functions and in preventing diseases. Technologies for delivering these nutrients and for monitoring their concentrations can help to ensure proper nutritional balance. Eccrine sweat is a potentially attractive class of biofluid for monitoring purposes due to the ability to capture sweat easily and noninvasively from nearly any region of the body using skin-integrated microfluidic technologies.

Bitter Flavored, Soft Composites for Wearables Designed to Reduce Risks of Choking in Infants.

Wireless, skin-integrated devices for continuous, clinical-quality monitoring of vital signs have the potential to greatly improve the care of patients in neonatal and pediatric intensive-care units. These same technologies can also be used in the home, across a broad spectrum of ages, from beginning to end of life. Although miniaturized forms of such devices minimize patient burden and improve compliance, they represent life-threatening choking hazards for infants.

Optically Activated 3D Thin-Shell TiO for Super-Sensitive Chemoresistive Responses: Toward Visible Light Activation.

One of the well-known strategies for achieving high-performance light-activated gas sensors is to design a nanostructure for effective surface responses with its geometric advances. However, no study has gone beyond the benefits of the large surface area and provided fundamental strategies to offer a rational structure for increasing their optical and chemical performances. Here, a new class of UV-activated sensing nanoarchitecture made of highly periodic 3D TiO, which facilitates 55 times enhanced light absorption by confining the incident light in the nanostructure, is prepared as an active gas channel.

Focused Electric-Field Polymer Writing: Toward Ultralarge, Multistimuli-Responsive Membranes.

The cost-effective direct writing of polymer nanofibers (NFs) has garnered considerable research attention as a compelling one-pot strategy for obtaining key building blocks of electrochemical and optical devices. Among the promising applications, the changes in optical response from external stimuli such as mechanical deformation and changes in the thermal environment are of great significance for emerging applications in smart windows, privacy protection, aesthetics, artificial skin, and camouflage. Herein, we propose a rational design for the mass production of customized NFs through the development of focused electric-field polymer writing (FEPW) coupled with the roll-to-roll technique.

High-Contrast Optical Modulation from Strain-Induced Nanogaps at 3D Heterogeneous Interfaces.

The realization of high-contrast modulation in optically transparent media is of great significance for emerging mechano-responsive smart windows. However, no study has provided fundamental strategies for maximizing light scattering during mechanical deformations. Here, a new type of 3D nanocomposite film consisting of an ultrathin (≈60 nm) AlO nanoshell inserted between the elastomers in a periodic 3D nanonetwork is proposed.

Hierarchically porous Au nanostructures with interconnected channels for efficient mass transport in electrocatalytic CO reduction.

Electrocatalytic CO reduction is a promising way to provide renewable energy from gaseous CO The development of nanostructures improves energy efficiency and selectivity for value-added chemicals, but complex nanostructures limit the CO conversion rates due to poor mass transport during vigorous electrolysis. Herein, we propose a three-dimensional (3D) hierarchically porous Au comprising interconnected macroporous channels (200-300 nm) and nanopores (∼10 nm) fabricated via proximity-field nanopatterning. The interconnected macropores and nanopores enable efficient mass transport and large active areas, respectively.