Characteristics of TAA-ZnS Buffer Layer by Addition of Sodium Citrate for CIGS Thin Film Solar Cell.

Zinc Sulfide (ZnS) is an environmentally friendly material with a wide bandgap ( = 3.7 eV) comparable to that of cadmium sulfide (CdS) (2.4 eV), which is conventionally used as buffer layer in Cu(In,Ga)Se2 (CIGS) thin film solar cells.

Electrical Characteristics Analysis of Bonded Cells for Shingled Modules.

A shingled module fabricated using electrically conductive adhesive (ECA) can increase the light-receiving area and provide greater power than a conventional module fabricated using solder-coated copper ribbons. However, several issues such as damage from laser cutting and poor contact by the conductive paste may arise. In this study, a 15.

Kerf-Less Exfoliated Thin Silicon Wafer Prepared by Nickel Electrodeposition for Solar Cells.

Ultra-thin and large-area silicon wafers with a thickness in the range of 20-70 μm, were produced by spalling using a nickel stressor layer. A new equation for predicting the thickness of the spalled silicon was derived from the Suo-Hutchinson mechanical model and the kinking mechanism. To confirm the reliability of the new equation, the proportional factor of stress induced by the nickel on the silicon wafer, was calculated.

Piezophototronic Effect Modulated Multilevel Current Amplification from Highly Transparent and Flexible Device Based on Zinc Oxide Thin Film.

In this work, a strain modulated highly transparent and flexible ZnO/Ag-nanowires/polyethylene terephthalate optoelectronic device is developed. By utilizing the applied external strain-induced piezophototronic effects of a ZnO thin film, a UV-generated photocurrent is tuned in a wide range starting from 0.01 to 85.

Influence of Post-Heat Treatment of ZnO:Al Transparent Electrode for Copper Indium Gallium Selenide Thin Film Solar Cell.

Copper indium gallium selenide (CIGS) thin film solar cells have been regarded as a candidate for energy conversion devices owing to their high absorption coefficient, high temperature stability, and low cost. ZnO:Al thin film is commonly used in CIGS solar cells as a window layer. In this study, ZnO:Al films were deposited on glass under various post-heat temperature using RF sputtering to observe the characteristics of ZnO:Al films such as Hall mobility, carrier concentration, and resistivity; subsequently, the ZnO:Al films were applied to a CIGS solar cell as a window.

Characterization of ZnS Thin Films Grown Using Chemical Bath Deposition with Three Different Complexing Agents.

Cadmium sulfide buffer layer was replaced with zinc sulfide thin film owing to toxicity. ZnS thin films were fabricated using chemical bath deposition. The inhibition of Zn(OH)2 and high uniformity are important factors for the deposition of ZnS.

Enhanced broadband photoresponse of a self-powered photodetector based on vertically grown SnS layers via the pyro-phototronic effect.

Here, we demonstrate the broadband photoresponse from ultraviolet (365 nm) to near-infrared (850 nm) wavelengths from a photodetector based on vertically grown SnS layers. Particularly, the photoinduced current density of the device increased from 100 to 470 μA cm with a wavelength of 760 nm and an intensity of 7 mW cm by utilizing the pyro-phototronic potential. In addition, the photodetector demonstrated ultrafast response rates of ∼12 μs for the rise and ∼55 μs for the decay times over the studied range.

Analysis of the Effect of Silicon with Nano-Size Surface Structure on an Electrode Formed Using Screen Printing.

In this paper, we report an investigation into the effects of the texturing size of silicon on the efficiency of a screen-printed Si solar cell. To accomplish this, we produced solar cells with various textured surfaces. The method we used to produce these cells included methods such as anisotropic chemical etching (texturing size of about 4 μm) using a mixed solution of KOH and IPA, reactive ion etching (texturing size of about 0.

Effect of an Ag Insertion Layer on the Optical and Electrical Properties of Ga Doped Zinc Oxide Films.

GZO/Ag/GZO films were investigated for use as high quality transparent conductive electrodes. The GZO and Ag films were deposited by RF sputtering and electron beam evaporation, respectively, at room temperature. The effects of Ag thickness and post heat treatment on the structural, electrical and optical properties of these multilayer films were investigated.

Fabrication of metal-coated carbon nanowalls synthesized by microwave plasma enhanced chemical vapor deposition.

In this study, the coating of synthesized carbon nanowalls (CNWs) with various metal layers (Ni, Cu, and W) was investigated. CNWs were synthesized by microwave plasma enhanced chemical vapor deposition (PECVD) with a methane (CH4) and hydrogen (H2) gas mixture on a p-type Si wafer, and then coated with metal films (Ni, Cu, and W) using an RF magnetron sputtering system with four-inch targets. Different sputtering times (5, 10, 20, and 30 min) were established to obtain different thicknesses of the metal layers with which the CNWs were coated.

SnO2 nanowire gas sensor operating at room temperature.

The NO2 gas sensor based on SnO2 semiconducting nanowires workable at room temperature has been investigated. The network structure of SnO2 nanowires was fabricated on the electrodes by a simple thermal evaporation process from Sn metal powders and oxygen gas. The diameter of the nanowires was 20-60 nm depending on the processing conditions.

Curcumin could prevent the development of chronic neuropathic pain in rats with peripheral nerve injury.

Background: Peripheral nerve injury results in chronic neuropathic pain characterized by allodynia and/or spontaneous pain. It has been suggested that activation of mitogen-activated protein kinases such as extracellular signal-regulated kinase (ERK) and c-Jun N-terminal kinase (JNK) contribute to the neuropathic pain.

Objectives: We investigated if curcumin could prevent the development of neuropathic pain in rats with chronic constriction injury (CCI) of the sciatic nerve.

Influence of various plasma treatment on the properties of carbon nanotubes for composite applications.

In present work, the effects of hydrogen and oxygen plasma treatments on the structural properties of carbon nanotubes (CNTs) synthesized by catalytic CVD (Chemical Vapor Deposition) have been systematically investigated. Field emission scanning electron microscopy (FE-SEM), high-resolution transmission electron microscopy (HRTEM), and Raman spectroscopy were used to characterize the microstructural changes of the CNTs. The oxygen plasma treatment resulted in that the nanoparticles were appeared at the surface of CNTs.

Structural, optical, and electrical properties of semiconducting ZnO nanosheets.

ZnO nanosheets were fabricated by an oxygen-assisted carbothermal reduction process and their properties were evaluated. In particular, the FET characteristics and photoluminescence properties of ZnO nanosheets were evaluated. The conduction type of ZnO nanosheets was determined as an n-type and the mobility was 20-40 cm2/ V-s, which is fairly high compared to ZnO nanowires.

A combination of lidocaine (lignocaine) and remifentanil reduces pain during propofol injection.

Objective: Pain on injection is a well known adverse effect of propofol. The purpose of this study was to compare the analgesic effect of a lidocaine (lignocaine)/remifentanil combination compared with either lidocaine alone or remifentanil alone during propofol injection for induction of anaesthesia.

Methods: In a randomised, double-blind, prospective trial, 129 patients were allocated to one of three groups (each n = 43) receiving lidocaine 20mg, remifentanil 0.