Highly flexible and transparent colorless polyimide substrate sandwiched between plasma polymerized fluorocarbon and InGaTiO for high performance flexible perovskite solar cells.

We integrated transparent antireflective coatings and transparent electrodes onto flexible colorless polyimide (CPI) substrates to fabricate high-performance flexible perovskite solar cells. Multifunctional PPFC/CPI/IGTO substrates were fabricated by sputtering the optimal plasma-polymerized fluorocarbon (PPFC) antireflective coating and InGaTiO (IGTO) electrode films on both sides of the CPI substrate. By applying PPFC with a low refractive index (1.

Development of shielding evaluation and management program for O-ring type linear accelerators.

The shielding parameters can vary depending on the geometrical structure of the linear accelerators (LINAC), treatment techniques, and beam energies. Recently, the introduction of O-ring type linear accelerators is increasing. The objective of this study is to evaluate the shielding parameters of new type of linac using a dedicated program developed by us named ORSE (O-ring type Radiation therapy equipment Shielding Evaluation).

Assessment of radio-activation using spectroscopy in medical linear accelerators.

In radiotherapy, when photon energy exceeding 8 MV is utilized, photoneutrons can activate the components within the gantry of the linear accelerator (linac). At the end of the linac's lifecycle, radiation workers are tasked with its dismantling and disposal, potentially exposing them to unintentional radiation. This study aims to identify and measure the radioisotopes generated by this activation through spectroscopy, and to evaluate the effective dose rate.

Comparison of skin dose in IMRT and VMAT with TrueBeam and Halcyon linear accelerator for whole breast irradiation.

With the increasing use of flattening filter free (FFF) beams, it is important to evaluate the impact on the skin dose and target coverage of breast cancer treatments. This study aimed to compare skin doses of treatments using FFF and flattening filter (FF) beams for breast cancer. The study established treatment plans for left breast of an anthropomorphic phantom using Halcyon's 6-MV FFF beam and TrueBeam's 6-MV FF beam.

Dosimetric verification of annual quality assurance for a linear accelerator using a transmission type detector.

The purpose of our study is to establish an efficient quality assurance (QA) procedure using a transmission-type detector (IBA, Stealth chamber), a reference signal detector, as a field chamber. Relative dosimetry items, including monitor unit linearity, output constancy based on dose rate and field size, and output factor were measured and compared with results obtained from the Farmer-type chamber (IBA, Wellhofer, FC65-G). Moreover, output for each field size was measured to assess its applicability to small fields.

Development of open access tool for automatic use factor calculation using DICOM-RT patient data.

Our study recalculated the use factor of linear accelerators (LINACs) by using an in-house program based on Digital Imaging and Communications in Medicine radiation therapy (DICOM-RT). We considered the impact of advancements and changes in treatment trends, including modality, technology, and radiation dose, on the use factor, which is one of the shielding parameters. In accordance with the methodology described in the NCRP 151 report, we computed the use factor for four linear accelerators (LINACs) across three hospitals.

Development of Total Lymphoid Irradiation (TLI)-Dedicated Shielding and Image-Guided System and Dose Evaluation Using 3D-Printed Rat Phantom.

Purpose: The purpose of this study is to propose a technique for delivering accurate doses in an image-guided system by developing an experimental setup optimized for total lymphoid irradiation (TLI) in rat lung transplantation.

Materials And Methods: In this study, a position-controlled shielding system was developed, and the dose was quantitatively evaluated using a 3D rat phantom and Gafchromic EBT3 film. In addition, we made our own image-guided system that allows the position of the rat and the shielding system to be confirmed during TLI.

Clinical Application Study of Semi-cylindrical Beam Spoiler for Radiation Treatment of Early-stage Glottic Cancer Patients.

Background/aim: The purpose of this study was to determine whether a semi-cylindrical beam spoiler (sCBS) developed herein effectively increases the skin dose in patients with early-stage glottic cancer.

Patients And Methods: We measured the surface doses for 26 patients who used the sCBS during treatment of early-stage glottic cancer through a parallel-opposed lateral two-field 6 MV photon beam. Measurements were performed by attaching optically stimulated luminescent dosimeters to the left, right, anterior (in-field), inferior, and superior (out-field) sides of the patient.

Room Temperature Processed Transparent Amorphous InGaTiO Cathodes for Semi-Transparent Perovskite Solar Cells.

In order to ensure high-performance semitransparent perovskite solar cells (ST-PSCs), the deposition of high-quality scalable transparent cathodes on ST-PSCs at room temperature is necessary. In this study, we designed an amorphous InGaTiO (IGTO) electrode, prepared by linear facing target sputtering (LFTS) as a transparent cathode for ST-PSCs. Even in the room temperature sputtering process, the amorphous IGTO cathode showed a low sheet resistance of 9.

Comparison of NiO thin film deposited by spin-coating or thermal evaporation for application as a hole transport layer of perovskite solar cells.

We compared nickel oxide (NiO ) deposited by thermal evaporation and that deposited by the spin-coating process, for use in the hole transport layers of inverted planar perovskite solar cells (PSCs). Spin-coating deposition for NiO HTL has been widely used, owing to its simplicity, low cost, and high efficiency. However, the spin-coating process has a technical limit to depositing a large-area uniformly.

Thermally-evaporated C/Ag/C multilayer electrodes for semi-transparent perovskite photovoltaics and thin film heaters.

We investigated the characteristics of thermally evaporated fullerene (C)/Ag/C (CAC) multilayer films for use in semi-transparent perovskite solar cells (PSCs) and thin-film heaters (TFHs). The top and bottom C layers and Ag interlayer were prepared using multi-source thermal evaporation, and the thickness of the Ag interlayer was investigated in detail for its effects on the resistivity, optical transmittance, and mechanical properties of the CAC electrodes. We used a figure-of-merit analysis to obtain a CAC electrode with a smooth surface morphology that exhibited a sheet resistance of 5.