Sensor Size Effect on Rayleigh Wave Velocity on Cementitious Surfaces.

Concrete properties and damage conditions are widely evaluated by ultrasonics. When access is limited, the evaluation takes place from a single surface. In this case, the sensor size plays a crucial role due to the "aperture effect".

Elastic Wave Monitoring of Cementitious Mixtures Including Internal Curing Mechanisms.

The mitigation of autogenous shrinkage in cementitious materials by internal curing has been widely studied. By the inclusion of water reservoirs, in form of saturated lightweight aggregates or superabsorbent polymers, additional water is provided to the hydrating matrix. The onset of water release is of high importance and determines the efficiency of the internal curing mechanism.

The Influence of Superabsorbent Polymers and Nanosilica on the Hydration Process and Microstructure of Cementitious Mixtures.

Superabsorbent polymers (SAPs) are known to mitigate the development of autogenous shrinkage in cementitious mixtures with a low water-to-cement ratio. Moreover, the addition of SAPs promotes the self-healing ability of cracks. A drawback of using SAPs lies in the formation of macropores when the polymers release their absorbed water, leading to a reduction of the mechanical properties.

Chasing the Bubble: Ultrasonic Dispersion and Attenuation from Cement with Superabsorbent Polymers to Shampoo.

This study aims to experimentally investigate the ultrasonic behavior of fresh cement focusing on the contribution of the entrapped air bubbles. Frequency dispersion and attenuation carry delicate information that is not possible to gather by traditional ultrasonic pulse velocity. This is measured by simple indicators that quantify the frequency dependence of propagation velocity of longitudinal waves through fresh cementitious media.

The Contribution of Elastic Wave NDT to the Characterization of Modern Cementitious Media.

To mitigate autogenous shrinkage in cementitious materials and simultaneously preserve the material's mechanical performance, superabsorbent polymers and nanosilica are included in the mixture design. The use of the specific additives influences both the hydration process and the hardened microstructure, while autogenous healing of cracks can be stimulated. These three stages are monitored by means of non-destructive testing, showing the sensitivity of elastic waves to the occurring phenomena.

Dimension Effects on the Acoustic Behavior of TRC Plates.

Acoustic emission (AE) is a monitoring technique that has proven its suitability in and outside of the laboratory in characterizing the structural condition of materials. In composites for construction and repair, several breakthroughs have been recently noted involving mainly fracture mode evaluation based on the AE waveform characteristics. However, the acquired signals, apart from the cracking source strongly depend on the size and shape of the plate specimens.

Evaluation of the Self-Healing Ability of Mortar Mixtures Containing Superabsorbent Polymers and Nanosilica.

Addition of superabsorbent polymers (SAPs) to cementitious mixtures promotes the self-healing ability of the material. When cracking occurs; SAPs present inside the crack will swell upon contact with water and subsequently release this water to stimulate the further hydration of unhydrated cement particles and the calcium carbonate crystallization. However; the inclusion of SAPs affects the mechanical performance of the cementitious material by the creation of macro-pores as water is retracted from the swollen SAP.

Concrete wave dispersion interpretation through Mindlin's strain gradient elastic theory.

Classical elastic wave features like pulse velocity and attenuation have been used for decades for concrete condition characterization. Relatively recently the effect of frequency has been studied showing no doubt over the dispersive behavior of the material. Despite the experimental evidence, there is no unified theory to model the material and explain this phase velocity change at frequencies below 200 kHz.

Evaluation of SHM system produced by additive manufacturing via acoustic emission and other NDT methods.

During the last decades, structural health monitoring (SHM) systems are used in order to detect damage in structures. We have developed a novel structural health monitoring approach, the so-called "effective structural health monitoring" (eSHM) system. The current SHM system is incorporated into a metallic structure by means of additive manufacturing (AM) and has the possibility to advance life safety and reduce direct operative costs.

Non-Destructive Evaluation for Corrosion Monitoring in Concrete: A Review and Capability of Acoustic Emission Technique.

Corrosion of reinforced concrete (RC) structures has been one of the major causes of structural failure. Early detection of the corrosion process could help limit the location and the extent of necessary repairs or replacement, as well as reduce the cost associated with rehabilitation work. Non-destructive testing (NDT) methods have been found to be useful for in-situ evaluation of steel corrosion in RC, where the effect of steel corrosion and the integrity of the concrete structure can be assessed effectively.

Fracture of human femur tissue monitored by acoustic emission sensors.

The study describes the acoustic emission (AE) activity during human femur tissue fracture. The specimens were fractured in a bending-torsion loading pattern with concurrent monitoring by two AE sensors. The number of recorded signals correlates well with the applied load providing the onset of micro-fracture at approximately one sixth of the maximum load.

Wave dispersion and attenuation on human femur tissue.

Cortical bone is a highly heterogeneous material at the microscale and has one of the most complex structures among materials. Application of elastic wave techniques to this material is thus very challenging. In such media the initial excitation energy goes into the formation of elastic waves of different modes.

Nondestructive damage evaluation in ceramic matrix composites for aerospace applications.

Infrared thermography (IRT) and acoustic emission (AE) are the two major nondestructive methodologies for evaluating damage in ceramic matrix composites (CMCs) for aerospace applications. The two techniques are applied herein to assess and monitor damage formation and evolution in a SiC-fiber reinforced CMC loaded under cyclic and fatigue loading. The paper explains how IRT and AE can be used for the assessment of the material's performance under fatigue.

Experimental study of surface wave propagation in strongly heterogeneous media.

In the present paper, the propagation of Rayleigh waves in a strongly heterogeneous medium is discussed. Scattering of stress waves is a difficult scientific problem. Specifically, the interaction of surface waves with distributed inhomogeneity seems highly complicated due to the existence of two displacement components.