Synthesis and Porous Structure Characteristics of Allyl Methacrylate/Divinylbenzene Polymers.

A set of six porous copolymers of allyl methacrylate (AllMeth) and divinylbenzene (DVB), containing 5 to 50 wt% of the latter crosslinker, are synthesized by suspension polymerization method in the presence of inert diluents. Obtained polymers have various specific surface areas-those with 20 to 50 wt% of DVB have a high surface area in the range of 410-480 m/g, depending only slightly on the amount of the aromatic crosslinker. Specific surface area decreases strongly only when DVB content is 15 and 5 wt%.

Kinetic, equilibrium, and thermodynamic aspects of phenol adsorption onto acrylonitrile-divinylbenzene copolymer.

Adsorption of phenol onto acrylonitrile-divinylbenzene copolymer (AN-DVB) was comprehensively investigated with the aspect of kinetic, equilibrium, and thermodynamic. The effect of adsorbent dosage, initial concentration, temperature, and pH were studied in batch adsorption process. Maximum phenol adsorption capacity was obtained at neutral pH of phenol solution (6.

Sinapic-Acid-Loaded Nanoparticles Optimized via Experimental Design Methods: Cytotoxic, Antiapoptotoic, Antiproliferative, and Antioxidant Activity.

Nanoparticles are frequently investigated as carrier systems that increase the biological activities of hydrophobic molecules, especially by providing them with water solubility. Sinapic acid (Sa), commonly found in plants, is a phenolic compound with a wide spectrum of biological activities and extensive pharmacological properties. The aim of this study was the synthesis/characterization of optimized sinapic-acid-loaded poly(lactic--glycolic acid) (PLGA) nanoparticles (SaNPs) to improve the solubility of sinapic acid (Sa) that limit its use in the biological system and investigate the biological activities of these nanoparticles in the breast cancer cell line.

Optimization of adaptive neuro-fuzzy inference system (ANFIS) parameters via Box-Behnken experimental design approach: The prediction of chromium adsorption.

Prediction of adsorption via Adaptive Neuro-Fuzzy Inference System (ANFIS) can save the cost and time in practical applications. Chromium (VI) adsorption data obtained at different temperature, activated carbon dosage and pH values were evaluated by using MATLAB ANFIS. In order to achieve prediction of adsorption via ANFIS with acceptable error values, optimum membership function (MF) and optimum number of MF were determined by using Box-Behnken experimental design (BBD) method.

Comparative evaluation of hesperetin loaded nanoparticles for anticancer activity against C6 glioma cancer cells.

The aim of this study was to evaluate anti-cancer properties of hesperetin (Hsp) and hesperetin-loaded poly(lactic-co-glycolic acid) nanoparticles (HspNPs) for glioblastoma treatment. Nanoparticles prepared by single emulsion method had a size of less than 300 nm with 70.7 ± 3.

Synthesis of hesperetin-loaded PLGA nanoparticles by two different experimental design methods and biological evaluation of optimized nanoparticles.

Hesperetin was effectively encapsulated into poly (d,l-lactic-co-glycolic acid) nanoparticles by using experimental design methods. A seven-factor Plackett-Burman design was used in order to determine the major process parameters. A significant linear equation, which shows the effect of each process parameter on encapsulation efficiency was developed, and then the most effective factors were determined.

Preparation of Fe oxide nanoparticles for environmental applications: arsenic removal.

The objective of this study is to examine the adsorption-desorption behavior of a magnetically active hybrid sorbent (MAHS) material, prepared by dispersing colloid-like hydrated iron oxide particles in the outer periphery of a macroporous ion-exchange resin (Amberlite XAD-2). The experimental results show that the new sorbent material can simultaneously remove arsenic (V) and a chlorinated organic compound (2,6-dichlorophenol [2,6-DCP]) from aqueous solutions at around neutral pH. The recovery of arsenic and 2,6-DCP from MAHS was conducted using a regenerant containing 50% (v/v) CH3OH + 3% (w/v) NaOH.