Molecular dynamics simulation-based study to analyse the properties of entrapped water between gold and graphene 2D interfaces.

Heterostructures based on graphene and other 2D materials have received significant attention in recent years. However, it is challenging to fabricate them with an ultra-clean interface due to unwanted foreign molecules, which usually get introduced during their transfer to a desired substrate. Clean nanofabrication is critical for the utilization of these materials in 2D nanoelectronics devices and circuits, and therefore, it is important to understand the influence of the "non-ideal" interface.

Highly Conductive PEDOT:PSS: Ag Nanowire-Based Nanofibers for Transparent Flexible Electronics.

Highly conductive, transparent, and easily available materials are needed in a wide range of devices, such as sensors, solar cells, and touch screens, as alternatives to expensive and unsustainable materials such as indium tin oxide. Herein, electrospinning was employed to develop fibers of PEDOT:PSS/silver nanowire (AgNW) composites on various substrates, including poly(caprolactone) (PCL), cotton fabric, and Kapton. The influence of AgNWs, as well as the applied voltage of electrospinning on the conductivity of fibers, was thoroughly investigated.

Printed synaptic transistor-based electronic skin for robots to feel and learn.

An electronic skin (e-skin) for the next generation of robots is expected to have biological skin-like multimodal sensing, signal encoding, and preprocessing. To this end, it is imperative to have high-quality, uniformly responding electronic devices distributed over large areas and capable of delivering synaptic behavior with long- and short-term memory. Here, we present an approach to realize synaptic transistors (12-by-14 array) using ZnO nanowires printed on flexible substrate with 100% yield and high uniformity.

High-performance printed electronics based on inorganic semiconducting nano to chip scale structures.

The Printed Electronics (PE) is expected to revolutionise the way electronics will be manufactured in the future. Building on the achievements of the traditional printing industry, and the recent advances in flexible electronics and digital technologies, PE may even substitute the conventional silicon-based electronics if the performance of printed devices and circuits can be at par with silicon-based devices. In this regard, the inorganic semiconducting materials-based approaches have opened new avenues as printed nano (e.

Glycine-Chitosan-Based Flexible Biodegradable Piezoelectric Pressure Sensor.

This paper presents flexible pressure sensors based on free-standing and biodegradable glycine-chitosan piezoelectric films. Fabricated by the self-assembly of biological molecules of glycine within a water-based chitosan solution, the piezoelectric films consist of a stable spherulite structure of β-glycine (size varying from a few millimeters to 1 cm) embedded in an amorphous chitosan polymer. The polymorphic phase of glycine crystals in chitosan, evaluated by X-ray diffraction, confirms formation of a pure ferroelectric phase of glycine (β-phase).

Heterogeneous integration of contact-printed semiconductor nanowires for high-performance devices on large areas.

In this work, we have developed a contact-printing system to efficiently transfer the bottom-up and top-down semiconductor nanowires (NWs), preserving their as-grown features with a good control over their electronic properties. In the close-loop configuration, the printing system is controlled with parameters such as contact pressure and sliding speed/stroke. Combined with the dry pre-treatment of the receiver substrate, the system prints electronic layers with high NW density (7 NWs/μm for bottom-up ZnO and 3 NWs/μm for top-down Si NWs), NW transfer yield and reproducibility.

Large-Area Self-Assembly of Silica Microspheres/Nanospheres by Temperature-Assisted Dip-Coating.

This work reports a temperature-assisted dip-coating method for self-assembly of silica (SiO) microspheres/nanospheres (SPs) as monolayers over large areas (∼cm). The area over which self-assembled monolayers (SAMs) are formed can be controlled by tuning the suspension temperature (T), which allows precise control over the meniscus shape. Furthermore, the formation of periodic stripes of SAMs, with excellent dimensional control (stripe width and stripe-to-stripe spacing), is demonstrated using a suitable set of dip-coating parameters.

Nanowire FET Based Neural Element for Robotic Tactile Sensing Skin.

This paper presents novel Neural Nanowire Field Effect Transistors (υ-NWFETs) based hardware-implementable neural network (HNN) approach for tactile data processing in electronic skin (e-skin). The viability of Si nanowires (NWs) as the active material for υ-NWFETs in HNN is explored through modeling and demonstrated by fabricating the first device. Using υ-NWFETs to realize HNNs is an interesting approach as by printing NWs on large area flexible substrates it will be possible to develop a bendable tactile skin with distributed neural elements (for local data processing, as in biological skin) in the backplane.