A Novel, Controllable, and Efficient Method for Building Highly Hydrophobic Aerogels.

Aerogels prepared using freeze-drying methods have the potential to be insulation materials or absorbents in the fields of industry, architecture, agriculture, etc., for their low heat conductivity, high specific area, low density, degradability, and low cost. However, their native, poor water resistance caused by the hydrophilicity of their polymer matrix limits their practical application.

Reduction of PVA Aerogel Flammability by Incorporation of an Alkaline Catalyst.

Sodium hydroxide was used as a base catalyst to reduce the flammability of poly(vinyl alcohol) (PVA) aerogels. The base-modified aerogels exhibited significantly enhanced compressive moduli, likely resulting in decreased gallery spacing and increased numbers of "struts" in their structures. The onset of decomposition temperature decreased for the PVA aerogels in the presence of the base, which appears to hinder the polymer pyrolysis process, leading instead to the facile formation of dense char.

Biomolecules as Flame Retardant Additives for Polymers: A Review.

Biological molecules can be obtained from natural sources or from commercial waste streams and can serve as effective feedstocks for a wide range of polymer products. From foams to epoxies and composites to bulk plastics, biomolecules show processability, thermal stability, and mechanical adaptations to fulfill current material requirements. This paper summarizes the known bio-sourced (or bio-derived), environmentally safe, thermo-oxidative, and flame retardant (BEST-FR) additives from animal tissues, plant fibers, food waste, and other natural resources.

Sustainable, Low Flammability, Mechanically-Strong Poly(vinyl alcohol) Aerogels.

Poly(vinyl alcohol) (PVA), tannic acid (TA) and sodium hydroxide (NaOH) were used to prepare low-flammability, mechanically-strong aerogels via an environmentally-friendly freeze-drying method. Because of the strong interaction between TA and PVA through hydrogen bonds, PVA/TA/NaOH aerogels exhibited compressive moduli as high as 12.7 MPa, 20 times that of the control PVA aerogel.

The Relation between the Rheological Properties of Gels and the Mechanical Properties of Their Corresponding Aerogels.

A series of low density, highly porous clay/poly(vinyl alcohol) composite aerogels, incorporating ammonium alginate, were fabricated via a convenient and eco-friendly freeze drying method. It is significant to understand rheological properties of precursor gels because they directly affect the form of aerogels and their processing behaviors. The introduction of ammonium alginate impacted the rheological properties of colloidal gels and improved the mechanical performance of the subject aerogels.

Clay-Facilitated Aqueous Dispersion of Graphite and Poly(vinyl alcohol) Aerogels Filled with Binary Nanofillers.

Dispersion of graphite in water was achieved using clay as dispersing aid. In the absence of polymer, the clay/graphite suspensions were sufficiently stable to produce aerogels composed of very thin layers of uniformly dispersed nanoparticles. Poly(vinyl alcohol) (PVOH) aerogels containing binary nanofillers (clay plus graphite) were then fabricated and tested.

Poly(Amide-imide) Aerogel Materials Produced via an Ice Templating Process.

Low density composites of sodium montmorillonite and poly(amide-imide) polymers have been created using an ice templating method, which serves as an alternative to the often-difficult foaming of high temperature/high performance polymers. The starting polymer was received in the poly(amic acid) form which can be cured using heat, into a water insoluble amide-imide copolymer. The resulting materials have densities in the 0.

Green Approach to Improving the Strength and Flame Retardancy of Poly(vinyl alcohol)/Clay Aerogels: Incorporating Biobased Gelatin.

Biobased gelatins were used to improve the compressive properties and flammability of poly(vinyl alcohol)/montmorillonite (PVA/MMT) aerogels, fabricated using a simple and environmentally friendly freeze-drying method. Because of the excellent compatibility and strong interfacial adhesion between PVA and gelatin, the compressive moduli of aerogels were enhanced dramatically with the incorporation of gelatin. PVA/MMT/porcine-gelatin aerogels exhibit compressive modulus values as much as 12.

Effect of polyethelene oxide on the thermal degradation of cellulose biofilm - Low cost material for soft tissue repair in dentistry.

Background: Bio cellulose is a byproduct of sweet tea fermentation known as kombusha. During the biosynthesis by bacteria cellulose chains are polymerized by enzyme from activated glucose. The single chains are then extruded through the bacterial cell wall.

Novel Polymer Aerogel toward High Dimensional Stability, Mechanical Property, and Fire Safety.

Inorganc silica-based aerogels, the earliest and widely used aerogels, have poorer mechanical properties than their organic substitutes, which are flammable. In this study, a novel polymeric aerogel with high strength, inherent flame retardancy, and cost-effectiveness, which is based on poly(vinyl alcohol) (PVA) cross-linked with melamine-formaldehyde (MF), was prepared under aqueous condition with an ecofriendly freeze-drying and postcuring process. Combined with the additional rigid MF network and benifited from the resulting unique infrastructure of inter-cross-linked flexible PVA segments and rigid MF segments, PVA-based aerogels exibited a significantly decreased degradation rate and sharply decreased peak heat release rate (PHRR) in cone calorimeter tests (by as much as 83%) compared with neat PVA.

Effect of Bulky Substituents in the Polymer Backbone on the Properties of Polyimide Aerogels.

With unique advantages over inorganic aerogels including higher strengths and compressive moduli, greater toughness, and the ability to be fabricated as a flexible thin film, polymer aerogels have the potential to supplant inorganic aerogels in numerous applications. Among polymer aerogels, polyimide aerogels possess a high degree of high thermal stability as well as outstanding mechanical properties. However, while the onset of thermal decomposition for these materials is typically very high (greater than 500 °C), the polyimide aerogels undergo dramatic thermally induced shrinkage at temperatures well below their glass transition (T) or decomposition temperature, which limits their use.

Tough Polymer Aerogels Incorporating a Conformal Inorganic Coating for Low Flammability and Durable Hydrophobicity.

Both inorganic and polymeric aerogels are well-known in the materials field. Inorganic aerogels are generally susceptible to brittle fracture, while polymeric aerogels tend to exhibit low modului and high flammability. To overcome these disadvantages, we introduce a new approach to the design of aerogels.

Clay Aerogel Supported Palladium Nanoparticles as Catalysts.

Highly porous, low density palladium nanoparticle/clay aerogel materials have been produced and demonstrated to possess significant catalytic activity for olefin hydrogenation and isomerization reactions at low/ambient pressures. This technology opens up a new route for the production of catalytic materials.

Biomass-Based Mechanically Strong and Electrically Conductive Polymer Aerogels and Their Application for Supercapacitors.

A novel biomass-based mechanically strong and electrically conductive polymer aerogel was fabricated from aniline and biodegradable pectin. The strong hydrogen bonding interactions between polyaniline (PANI) and pectin resulted in a defined structure and enhanced properties of the aerogel. All the resultant aerogels exhibited self-surppoted 3D nanoporous network structures with high surface areas (207-331m(2)/g) and hierarchical pores.

Nonflammable Alginate Nanocomposite Aerogels Prepared by a Simple Freeze-Drying and Post-Cross-Linking Method.

Nonflammable materials based on renewable ammonium alginate and nano fillers (nanoscale magnesium hydroxide, nanoscale aluminum hydroxide, layered double hydroxide, sodium montmorillonite, and Kaolin) were fabricated through a simple, environmentally friendly freeze-drying process, in which water was used as a solvent. A simple and economic post-cross-linking method was used to obtain homogeneous samples. The microstructure of the cross-linked alginate aerogels show three-dimensional networks.

Effects of Fiber Reinforcement on Clay Aerogel Composites.

Novel, low density structures which combine biologically-based fibers with clay aerogels are produced in an environmentally benign manner using water as solvent, and no additional processing chemicals. Three different reinforcing fibers, silk, soy silk, and hemp, are evaluated in combination with poly(vinyl alcohol) matrix polymer combined with montmorillonite clay. The mechanical properties of the aerogels are demonstrated to increase with reinforcing fiber length, in each case limited by a critical fiber length, beyond which mechanical properties decline due to maldistribution of filler, and disruption of the aerogel structure.

Effects of Molecular Weight upon Irradiation-Cross-Linked Poly(vinyl alcohol)/Clay Aerogel Properties.

Facile fabrication of mechanically strong poly(vinyl alcohol) (PVOH)/clay aerogel composites through a combination of increasing polymer molecular weights and gamma irradiation-cross-linking is reported herein. The aerogels produced from high polymer molecular weights exhibit significantly increased compressive moduli, similar to the effect of irradiation-induced cross-linking. The required irradiation dose for fabricating strong PVOH composite aerogels with dense microstructure decreased with increasing polymer molecular weight.

Efficient approach to improving the flame retardancy of poly(vinyl alcohol)/clay aerogels: incorporating piperazine-modified ammonium polyphosphate.

Ammonium polyphosphates (APP) modified with piperazine (PA-APP) was used to improve the flame retardancy of poly(vinyl alcohol) (PVA)/montmorillonite (MMT) aerogels, which were prepared via an environmentally friendly freeze-drying method. The thermal stabilities of the samples were evaluated by thermogravimetric analysis (TG); the flammability behaviors of samples were investigated by limiting oxygen index (LOI), vertical burning test (UL-94) and cone calorimeter (CC) tests. TG test results showed that the 5% weight loss temperature (T5%) of PVA/MMT/PA-APP was 10 °C higher than that of PVA/MMT/APP.

Fabrication and properties of irradiation-cross-linked poly(vinyl alcohol)/clay aerogel composites.

Poly(vinyl alcohol) (PVOH)/clay aerogel composites were fabricated by an environmentally friendly freeze-drying of the aqueous precursor suspensions, followed by cross-linking induced by gamma irradiation without chemical additives. The influences of cross-linking conditions, i.e.

Preparation and flammability of poly(vinyl alcohol) composite aerogels.

Poly(vinyl alcohol) (PVOH)-based aerogel composites with nanoscale silica, halloysite, montmorillonite (MMT), and laponite were prepared via a freeze-drying method. The PVOH/MMT and PVOH/laponite composites exhibit higher compressive moduli than the PVOH/SiO2 or PVOH/halloysite samples. Layered microstructures were observed for the samples except with PVOH/laponite, which showed irregular network morphologies.

Biodegradable pectin/clay aerogels.

Biodegradable, foamlike materials based on renewable pectin and sodium montmorillonite clay were fabricated through a simple, environmentally friendly freeze-drying process. The addition of multivalent cations (Ca(2+) and Al(3+)) resulted in apparent cross-linking of the polymer and enhancement of aerogel properties. The compressive properties increased as the solid contents (both pectin and clay) increased; moduli in the range of 0.

Graphene arrested in laponite-water colloidal glass.

Graphene production in water from graphite sources is an important technological route toward harvesting the unique properties of this material. Graphene forms thermodynamically unstable dispersions in water, limiting the use of this solvent due to aggregation. We show that graphene-water dispersions can be controlled kinetically to produce graphene by using laponite clay.