Nano Pd doped Ni foam electrode stimulated electrochemical reduction of tetrabromobisphenol A: Optimization strategies and function mechanism.

Tetrabromobisphenol A (TBBPA), a hazardous and persistent flame retardant, has been widely detected in the natural aquatic system. The acceleration of reductive debromination (rate-limiting process) is vital during the decomposition and detoxification of TBBPA. This study achieved superior TBBPA electrochemical reductive debromination performance by nano Pd doped Ni foam electrode (4.

Biodegradation and metabolism of tetrabromobisphenol A in microbial fuel cell: Behaviors, dynamic pathway and the molecular ecological mechanism.

Tetrabromobisphenol A (TBBPA) has aroused widespread pollution in industrial wastewater. Microbial fuel cell (MFC) was proved powerful in organics degradation and simultaneous resource recovery during wastewater treatment. However, the TBBPA biotransformation potential, pathway and the related molecular mechanism remain poorly understood.

A Flexible Solid Electrolyte Interphase Layer for Long-Life Lithium Metal Anodes.

Lithium (Li) metal is a promising anode material for high-energy density batteries. However, the unstable and static solid electrolyte interphase (SEI) can be destroyed by the dynamic Li plating/stripping behavior on the Li anode surface, leading to side reactions and Li dendrites growth. Herein, we design a smart Li polyacrylic acid (LiPAA) SEI layer high elasticity to address the dynamic Li plating/stripping processes by self-adapting interface regulation, which is demonstrated by in situ AFM.

Stable Li Metal Anodes via Regulating Lithium Plating/Stripping in Vertically Aligned Microchannels.

Li anodes have been rapidly developed in recent years owing to the rising demand for higher-energy-density batteries. However, the safety issues induced by dendrites hinder the practical applications of Li anodes. Here, Li metal anodes stabilized by regulating lithium plating/stripping in vertically aligned microchannels are reported.

Triboelectric Nanogenerator Enhanced Nanofiber Air Filters for Efficient Particulate Matter Removal.

We developed a high-efficiency rotating triboelectric nanogenerator (R-TENG) enhanced polyimide (PI) nanofiber air filter for particulate matter (PM) removal in ambient atmosphere. The PI electrospinning nanofiber film exhibited high removal efficiency for the PM particles that have diameters larger than 0.5 μm.

A new strategy for the synthesis of iron-oxide nanocrystals by using a single-spinneret electrospinning technique.

Iron-oxide nanocrystals (IONCs) have been widely researched, owing to their unique physical and chemical properties. Herein, a new strategy that involves an electrospinning technique with the addition of a surfactant is reported as an effective method for the fabrication of shaped IONCs. With the same precursor compositions, only iron-oxide nanoparticles were obtained by using a sol-gel method without electrospinning.

Synthesis of nanostructured SnO2/C microfibers with improved performances as anode material for Li-ion batteries.

Nanostructured SnO2/C microfibers were prepared by thermal decomposition of tin alginate fibers produced via wet-spinning technique. Results of X-ray diffraction and scanning electron microscopy show that the as-obtained SnO2/C microfibers consist of nano-sized SnO2 crystals with a mean diameter of 10-15 nm. Transmission electron microscopy visualization reveals that the composite fibers exhibit a porous structure consisting of both micropores and mesopores.

Fabrication characterization and activity of a solar light driven photocatalyst: cerium doped TiO2 magnetic nanofibers.

A novel magnetic separable composite photocatalytic nanofiber consisting of TiO2 as the major phase, CeO(2-y) and CoFe2O4 as the dopant phase was prepared by sol-gel method and electrospinning technique, and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV-vis diffuse reflectance spectrum (UV-vis DRS) and vibrating sample magnetometer (VSM). The photocatalytic activity of the resultant CoFe2O4-TiO2 and CeO(2-y)/CoFe2O4-TiO2 nanofibers was evaluated by photodegradation of methylene blue (MB) in an aqueous solution under xenon lamp (the irradiation spectrum energy distribution is similar to sunlight) irradiation in a photochemical reactor. The results showed that the dopant of Ce could affect the absorbance ability and photo-response range.

Direct formation of reusable TiO2/CoFe2O4 heterogeneous photocatalytic fibers via two-spinneret electrospinning.

A reusable photocatalytic TiO2/CoFe2O4 composite nanofiber was directly formed by using a vertical two-spinneret electrospinning process and sol-gel method, followed by heat treatment at 550 degrees C for 2 h. The high photocatalytic activity of the composite nanofibers depends on the good morphology of the fibers and the appropriate calcination temperature. The crystal structure and magnetic properties of the fibers were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersion spectroscopy (EDS), transmission electron microscope (TEM) and vibrating sample magnetometer (VSM).

Microstructure and magnetic property of M-type SrRe(x)Fe(12-x)O19 by sol-gel method.

Magnetoplumbite-type (M-type) SrRE(x)Fe(12-x)O19 (RE = La and Ce, x = 0-1.0) powders were prepared by a citric acid sol-gel technique and subsequent heat treatment. The crystal structure, grain size and magnetic properties were investigated by X-ray Diffraction (XRD), Scanning Electron Microscope (SEM) and vibrating sample magnetometer (VSM).

Polyethylene glycol-directed SnO2 nanowires for enhanced gas-sensing properties.

SnO(2) nanowires with lengths in the tens of micrometres range have been synthesized on a large scale via a facile polyethylene glycol-directed method at ambient temperature followed by a suitable thermal treatment of the precursor nanowires. The morphology of the precursor of the SnO(2) nanowires is tunable by changing the concentration of either SnCl(2) or polyethylene glycol. After calcination, the resulting SnO(2) nanowires retain a similar shape to the precursor, but with hierarchical architecture, which can be considered as one-dimensional nanowires assembled by interconnected SnO(2) nanoparticles with a high surface-to-volume ratio.

Cell adhesive and growth behavior on electrospun nanofibrous scaffolds by designed multifunctional composites.

Nanostructured biocomposite scaffolds of poly(l-lactide) (PLLA) blended with collagen (coll) or hydroxyapatite (HA), or both for tissue engineering application, were fabricated by electrospinning. The electrospun scaffolds were characterized for the morphology, chemical and tensile properties by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), water contact angle (WCA), Fourier transform infrared (FTIR) measurement, and tensile testing. Electrospun biocomposite scaffolds of PLLA and collagen or (and) HA in the diameter range of 200-700 nm mimic the nanoscale structure of the extracellular matrix (ECM) with a well-interconnection pore network structure.