Aquivion-Based Spray Freeze-Dried Composite Materials for the Cascade Production of γ-Valerolactone.

The development of multifunctional catalysts is a necessary step to effectively carry out one-pot cascade reactions, such as that from furfural to γ-valerolactone. This research effort faces the challenge posed by the intrinsic limit of how many kinds of catalytic sites a single material can bear. In this work, the application of Spray-Freeze Drying (SFD) as a synthetic technique for the preparation of a wide range of innovative composite multi-functional catalysts is reported.

Ce-radical Scavenger-Based Perfluorosulfonic Acid Aquivion Membrane for Pressurised PEM Electrolysers.

A Ce-radical scavenger-based perfluorosulfonic acid (PFSA) Aquivion membrane (C98 05S-RSP) was developed and assessed for polymer electrolyte membrane (PEM) electrolyser applications. The membrane, produced by Solvay Specialty Polymers, had an equivalent weight (EW) of 980 g/eq and a thickness of 50 μm to reduce ohmic losses at a high current density. The electrochemical properties and gas crossover through the membrane were evaluated upon the formation of a membrane-electrode assembly (MEA) in a range of temperatures between 30 and 90 °C and at various differential pressures (ambient, 10 and 20 bars).

Influence of Ionomer Content in the Catalytic Layer of MEAs Based on Aquivion Ionomer.

Perfluorinated sulfonic acid (PFSA) polymers such as Nafion are widely used for both electrolyte membranes and ionomers in the catalytic layer of membrane-electrode assemblies (MEAs) because of their high protonic conductivity, σ, as well as chemical and thermal stability. The use of PFSA polymers with shorter side chains and lower equivalent weight (EW) than Nafion, such as Aquivion PFSA ionomers, is a valid approach to improve fuel cell performance and stability under drastic operative conditions such as those related to automotive applications. In this context, it is necessary to optimize the composition of the catalytic ink, according to the different ionomer characteristics.

Mechanocatalytic Depolymerization of Cellulose With Perfluorinated Sulfonic Acid Ionomers.

Here, we investigated that the mechanocatalytic depolymerization of cellulose in the presence of Aquivion, a sulfonated perfluorinated ionomer. Under optimized conditions, yields of water soluble sugars of 90-97% were obtained using Aquivion PW98 and PW66, respectively, as a solid acid catalyst. The detailed characterization of the water soluble fraction revealed (i) the selective formation of oligosaccharides with a DP up to 11 and (ii) that depolymerization and reversion reactions concomitantly occurred during the mechanocatalytic process, although the first largely predominated.

Conversion of Cellulose into Amphiphilic Alkyl Glycosides Catalyzed by Aquivion, a Perfluorosulfonic Acid Polymer.

The perfluorosulfonic acid (PFSA) Aquivion PW98 is an amphiphilic solid superacid which is shown to catalyze the conversion of cellulose into amphiphilic alkyl glycosides (AAGs) in 85 % yield (with 97 % selectivity). The process involves a mechanocatalytic depolymerization of cellulose followed by a direct glycosylation with n-dodecanol. In comparison to H SO and solid acid catalysts commonly employed in cellulose processing, Aquivion PFSA PW98 is not only recyclable but also exhibits superior catalytic performances in terms of yield, selectivity, and reactor productivity.

Quantitative in Situ Analysis of Ionomer Structure in Fuel Cell Catalytic Layers.

A quantitative in situ investigation of the structure of the catalytic layer of polymer electrolyte membrane fuel cells using material-sensitive and conductive atomic force microscopy is reported. The distribution and size of the ionomer phase at the surface of the catalytic layer is retrieved from adhesion force mappings, measured at high humidity and up to 75 °C. The average ionomer layer thickness varies between 7 and 13 nm for three differently prepared samples, as concluded from the histograms.

Advances in parallel screening of drug candidates.

In the hit to lead process, a drug candidate is selected from a set of potential leads by screening its binding with potential targets. This review focuses on the lead identification assays that employ a bio-chemical or bio-physical test to detect molecular recognition events between proteins and small molecules in a parallel format. These tests require either the lead or the target immobilization followed by incubation with the set of potential interaction partners and detection of a signal related to the target-ligand binding.

Advanced polymers for molecular recognition and sensing at the interface.

In the few last years, the need of reliable, fast and inexpensive methods for selective analysis of specific substances in complex mixtures has grown exponentially. In particular, the detection of biomolecules, such as oligonucleotides, proteins, peptides and carbohydrates is of outstanding importance in gene expression, drug design and medicine studies. To these purposes, molecular recognition on microarray-configured devices is one of the most promising tools.