Stretchable, Sensitive Strain Sensors with a Wide Workable Range and Low Detection Limit for Wearable Electronic Skins.

With the rapid development of wearable electronics, a multifunctional and flexible strain sensor is urgently required. Even though enormous progress has been achieved in designing high-performance strain sensors, the conflict between high sensitivity and a large workable range still restricts their further advance. Herein, a "point to point" conductive network is proposed to design and fabricate a carbon black/polyaniline nanoparticles/thermoplastic polyurethane film (CPUF).

Synergistic Effect of Pressurization Rate and β-Form Nucleating Agent on the Multi-Phase Crystallization of iPP.

Using a homemade pressure device, we explored the synergistic effect of pressurization rate and β-form nucleating agent (β-NA) on the crystallization of an isotactic polypropylene (iPP) melt. The obtained samples were characterized by combining small angle X-ray scattering and synchrotron wide angle X-ray diffraction. It was found that the synergistic application of pressurization and β-NA enables the preparation of a unique multi-phase crystallization of iPP, including β-, γ- and/or mesomorphic phases.

Polymorph selection during melt crystallization of the isotactic polybutene-1 homopolymer depending on the melt state and crystallization pressure.

This work investigated the crystalline forms obtained from melt crystallization in the isotactic polybutene-1 (iPB-1) homopolymer via manipulation of the temperature at which samples were melted (Tmelt) and crystallization pressure (Pcry). Unlike the results under atmospheric conditions where the molten sample crystallized into the pure form II and the crystallization temperature and kinetics were affected obviously by Tmelt, the melted sample crystallized into forms II or I' under high pressure, depending on Tmelt and Pcry. The content of form I' decreases with increasing Tmelt or decreasing Pcry.

Structure and Mechanical Properties of Multi-Walled Carbon Nanotubes-Filled Isotactic Polypropylene Composites Treated by Pressurization at Different Rates.

Isotactic polypropylene filled with 1 wt.% multi-walled carbon nanotubes (iPP/MWCNTs) were prepared, and their crystallization behavior induced by pressurizing to 2.0 GPa with adjustable rates from 2.

A Study of the Pressure-Induced Solidification of Polymers.

By using a self-designed pressure-jump apparatus, we investigated the melt solidification behavior in the rapid compression process for poly-ethylene-terephthalate (PET), polyether-ether-ketone (PEEK), isotactic polypropylene (iPP), high-density polyethylene (HDPE), and the living polymer sulfur. The experimental results clearly show that crystallization could be inhibited, and some melts were solidified to the full amorphous state for PET, PEEK, and sulfur. Full amorphous PEEK that was 24 mm in diameter and 12 mm in height was prepared, which exceeded the size obtained by the melt quenching method.

Pressure-jump induced rapid solidification of melt: a method of preparing amorphous materials.

By using a self-designed pressure-jump apparatus, we investigated the melt solidification behavior in rapid compression process for several kinds of materials, such as elementary sulfur, polymer polyether-ether-ketone (PEEK) and poly-ethylene-terephthalate, alloy LaAlCuCo and NdCuNiAl. Experimental results clearly show that their melts could be solidified to be amorphous states through the rapid compression process. Bulk amorphous PEEK with 24 mm in diameter and 12 mm in height was prepared, which exceeds the size obtained by melt quenching method.

Simulation of Jetting in Injection Molding Using a Finite Volume Method.

In order to predict the jetting and the subsequent buckling flow more accurately, a three dimensional melt flow model was established on a viscous, incompressible, and non-isothermal fluid, and a control volume-based finite volume method was employed to discretize the governing equations. A two-fold iterative method was proposed to decouple the dependence among pressure, velocity, and temperature so as to reduce the computation and improve the numerical stability. Based on the proposed theoretical model and numerical method, a program code was developed to simulate melt front progress and flow fields.

Unusual structural evolution of poly(lactic acid) upon annealing in the presence of an initially oriented mesophase.

Uniaxial deformations of amorphous poly(lactic acid) (PLA) films were performed at two different temperatures, 70 and 80 °C, at various draw strains. The samples deformed at 70 °C showed a strain-induced mesophase, and the structural ordering and thermal stability increased as the draw strain increased. Further annealing was performed in situ at constant length at the drawing temperature of 70 °C for the films drawn to strains of 100% and 230%.

Identifying the phase behavior of biodegradable poly(hexamethylene succinate-co-hexamethylene adipate) copolymers with FTIR.

Whether a phase separation or a cocrystallization occurs in poly(hexamethylene succinate-co-hexamethylene adipate) (P(HS-co-HA)) copolymers was studied with a combination of wide-angle X-ray diffraction (WAXD) and Fourier transform infrared (FTIR) spectroscopy. With HA as the majority, the presence of HS comonomers leads to weakening and broadening of (10l) peaks in the X-ray fiber diffraction patterns, while a crystal structure similar to PHS is formed in the copolymer with HS as the majority. The X-ray diffraction patterns imply possible cocrystallization between HS and HA comonomers, but cannot lead to an unambiguous conclusion, which was clarified with the compensative tool of FTIR.

Phase transition of [C(n)-mim][PF6] under high pressure up to 1.0 GPa.

Behavior of the phase transition of an ionic liquid, [Cn-mim][PF(6)], has been investigated under pressures up to 1.0 GPa by using a high-pressure differential thermal analysis (DTA) apparatus. The T versus P phase diagrams of [BMIM][PF(6)] and [EMIM][PF(6)] are constructed.