Utilization of group 10 2D TMDs-PdSe as a nonlinear optical material for obtaining switchable laser pulse generation modes.

In-plane anisotropic two-dimensional (2D) materials have gained considerable interest in the field of research, due to having the potential of being used in different device applications. Recently, among these 2D materials, group 10 transition metal dichalcogenides (TMDs) pentagonal Palladium diselenide (PdSe) is utilized in various sections of researches like nanoelectronics, thermoelectric, spintronics, optoelectronics, and ultrafast photonics, owing to its high air stability and broad absorption spectrum properties. In this paper, it is demonstrated that by utilizing this novel 2D layered PdSe material as a saturable absorber (SA) in an EDF laser system, it is possible to obtain switchable laser pulse generation modes.

InSe nanosheets with broadband saturable absorption used for near-infrared femtosecond laser mode locking.

Indium selenide (InSe) has attracted tremendous attention due to its favorable electronic features, broad tunable bandgap, high stability and other attractive properties. However, its further applications for nonlinear optics have not yet been fully explored. In this work, we demonstrate that few-layer α-InSe nanosheets exhibit strong saturable absorption properties over a wide wavelength range covering 800, 1064 and 1550 nm.

Passively Q-switched Ytterbium-doped fiber laser based on broadband multilayer Platinum Ditelluride (PtTe) saturable absorber.

Two-dimensional (2D) layered Platinum Ditelluride (PtTe), a novel candidate of group 10 transition-metal dichalcogenides (TMDs), which provides enormous potential for pulsed laser applications due to its highly stable and strong nonlinear optical absorption (NOA) properties. PtTe saturable absorber (SA) is successfully fabricated with firstly demonstrated the passively Q-switched laser operation within a Yb-doped fiber laser cavity at 1066 nm. Few layered PtTe is produced by uncomplicated and cost-efficient ultrasonic liquid exfoliation and follow by incorporating into polyvinyl alcohol (PVA) polymer to form a PtTe-PVA composite thin film saturable absorber.

Laser Q-switching with PtS microflakes saturable absorber.

Numerous studies have been conducted to explore the performance of two-dimensional (2D) layered nano-materials based saturable absorber (SA) for pulsed laser applications. However, fabricating materials in nanoscale requires complicated preparation processes, high energy consumption, and high expertise. Hence, the study of pulsed laser performance based on the saturable absorber prepared by layered materials with bulk-micro size have gained a great attention.

Multifunctional Sensor Based on Porous Carbon Derived from Metal-Organic Frameworks for Real Time Health Monitoring.

Flexible and sensitive sensors that can detect external stimuli such as pressure, temperature, and strain are essential components for applications in health diagnosis and artificial intelligence. Multifunctional sensors with the capabilities of sensing pressure and temperature simultaneously are highly desirable for health monitoring. Here, we have successfully fabricated a flexible and simply structured bimodal sensor based on metal-organic frameworks (MOFs) derived porous carbon (PC) and polydimethylsiloxane (PDMS) composite.

Enhanced Photocatalytic Activity of WS Film by Laser Drilling to Produce Porous WS/WO Heterostructure.

Methods and mechanisms for improvement of photocatalytic activity, are important and popular research topics for renewable energy production and waste water treatment. Here, we demonstrate a facile laser drilling method for engineering well-aligned pore arrays on magnetron-sputtered WS nanofilms with increased active edge sites; the proposed method promotes partial oxidation to fabricate WS/WO heterojunctions that enhance the separation of photogenerated electron-hole pairs. The WS film after one, two, and three treatments exhibited photocurrent density of 3.

The WS2 quantum dot: preparation, characterization and its optical limiting effect in polymethylmethacrylate.

Due to the matching surface energy, WS2 quantum dots (QDs) can be obtained through direct liquid exfoliation in N-methyl-2-pyrrolidone rather than an ethanol and water mixture. Ultra-small WS2 QDs with a diameter of 2.4 nm are fabricated by an ultrasound method followed by high speed centrifugation up to 10 000 rpm.

Infrared light gated MoS₂ field effect transistor.

Molybdenum disulfide (MoS₂) as a promising 2D material has attracted extensive attentions due to its unique physical, optical and electrical properties. In this work, we demonstrate an infrared (IR) light gated MoS₂ transistor through a device composed of MoS₂ monolayer and a ferroelectric single crystal Pb(Mg(1/3)Nb(2/3))O₃-PbTiO₃ (PMN-PT). With a monolayer MoS₂ onto the top surface of (111) PMN-PT crystal, the drain current of MoS₂ channel can be modulated with infrared illumination and this modulation process is reversible.

Tuning nonlinear optical absorption properties of WS₂ nanosheets.

To control the optical properties of two-dimensional (2D) materials is a long-standing goal, being of both fundamental and technological significance. Tuning nonlinear optical absorption (NOA) properties of 2D transition metal dichalcogenides in a cost effective way has emerged as an important research topic because of its possibility to custom design NOA properties, implying enormous applications including optical computers, communications, bioimaging, and so on. In this study, WS2 with different size and thickness distributions was fabricated.

High-power passively mode-locked Nd:YVO(4) laser using SWCNT saturable absorber fabricated by dip coating method.

Passive mode locked laser is typically achieved by the Semiconductor Saturable absorber Mirror, SESAM, saturable absorber, which is produced by expensive and complicated metal organic chemical vapor deposition method. Carbon based single wall carbon nanotube (SWCNT), saturable absorber, is a promising material which is capable to produce stable passive mode-locking in the high power laser cavity over a wide operational wavelength range. This study has successfully demonstrated the high power mode locking laser system operating at 1 micron by using SWCNT based absorbers fabricated by dip coating method.

Improved multiphoton ultraviolet upconversion photoluminescence in ultrasmall core-shell nanocrystals.

Near-infrared to ultraviolet multiphoton upconversion photoluminescence in ultrasmall Tm3+/Yb3+-codoped CaF2 nanocrystals (∼6.7  nm in size) was observed and further significantly enhanced by growing an active shell of NaYF4:Yb3+. Owing to the active shell, the lanthanide emitters inside the core are effectively prevented from the surface quenchers, and the excitation energy is absorbed more efficiently via the additional luminescence sensitizer Yb embedded in the shell.

Controllable parabolic lensed liquid-core optical fiber by using electrostatic force.

For typical optical fiber system, an external lens accessory set is required to adjust the optical path of output light, which however is limited by the fixed parameter of the lens accessory setup. Considering spherical aberration in the imaging process and its small focusable spot size, a complicated lens combination is required to compensate the aberration. This paper has demonstrated a unique method to fabricate liquid-core lensed fibers by filling water and NOA61 respectively into hollow Teflon AF fibers and silicate fiber, the radius of curvature of the liquid lens can be controlled by adjusting the applied voltage on the core liquid and even parabolic shape lens can be produced with enough applied voltage.