Velocimetry of GHz elastic surface waves in quartz and fused silica based on full-field imaging of pump-probe reflectometry.

This study reports an imaging method for gigahertz surface acoustic waves in transparent layers using infrared subpicosecond laser pulses in the ablation regime and an optical pump-probe technique. The reflectivity modulations due to the photoelastic effect of generated multimodal surface acoustic waves were imaged by an sCMOS camera illuminated by the time-delayed, frequency-doubled probe pulses. Moving the delay time between , image stacks of wave field propagation were created.

Comparison of methods for estimating Young's moduli of mortar specimens.

Precisely estimating material parameters for cement-based materials is crucial for assessing the structural integrity of buildings. Both destructive (e.g.

Numerical evaluation of internal femur osteosynthesis based on a biomechanical model of the loading in the proximal equine hindlimb.

Femoral fractures are often considered lethal for adult horses because femur osteosynthesis is still a surgical challenge. For equine femur osteosynthesis, primary stability is essential, but the detailed physiological forces occurring in the hindlimb are largely unknown. The objective of this study was to create a numerical testing environment to evaluate equine femur osteosynthesis based on physiological conditions.

Frozen, Cold, or Cool? Chemical Assessment of the Effectiveness of Storage Conditions for Celluloid 3D Objects.

Preserving celluloid artifacts is challenging for museums, as this plastic is highly prone to degradation. Frozen, cold, and cool storage solutions are typically recommended for inhibiting the chemical degradation of celluloid. However, they are rarely implemented for three-dimensional celluloid (3D-CN) objects because low temperatures might cause irreversible effects (e.

Estimating Young's moduli based on ultrasound and full-waveform inversion.

Ultrasound is commonly utilized to determine the dynamic Young's moduli for estimating material deterioration or quantifying material parameters. This is either done with a resonance frequency analysis or ultrasound for rock or concrete specimens in geophysics or civil engineering. For ultrasound, these are typically cylindrical specimens measured in a through-transmission arrangement.

Mock-Ups in Plastic Conservation Research: Processing and Aging of 3D Celluloid Specimens Simulating Historical Objects.

The preparation of mock-ups in heritage science studies represents a valid alternative for investigation purposes, avoiding extensive sampling of cultural heritage objects. This work presents for the first time the successful preparation of three dimensional (3D) mock-ups made of celluloid, considering a combination of historical industrial production strategies and small-scale lab facilities. Prefabricated transparent celluloid sheets were acquired and then shaped through compression molding for creating mock-ups with 3D geometries.

Broadband Air-Coupled Ultrasound Emitter and Receiver Enable Simultaneous Measurement of Thickness and Speed of Sound in Solids.

Air-coupled ultrasound sensors have advantages over contact ultrasound sensors when a sample should not become contaminated or influenced by the couplant or the measurement has to be a fast and automated inline process. Thereby, air-coupled transducers must emit high-energy pulses due to the low air-to-solid power transmission ratios (10 to 10). Currently used resonant transducers trade bandwidth-a prerequisite for material parameter analysis-against pulse energy.

The restoration and erection of the world's first elevated obelisk.

Obelisks presented an important element in the architecture of ancient Egypt. This research is concerned with the re-erection of an obelisk that belongs to the famous Pharoah Ramses II. It was found broken and was transported to the Grand Egyptian Museum for restoration and display.

Evaluation of the Behavior of Carbon Short Fiber Reinforced Concrete (CSFRC) Based on a Multi-Sensory Experimental Investigation and a Numerical Multiscale Approach.

Carbon fiber reinforcement used in concrete has become a remarkable alternative to steel fibers. Admixing short fibers to fresh concrete and processing the material with a 3D printer leads to an orientation of fibers and a material with high uniaxial strength properties, which offers an economic use of fibers. To investigate its mechanical behavior, the material is subjected to flexural and tensional tests, combining several measuring techniques.

Improving mandibular reconstruction by using topology optimization, patient specific design and additive manufacturing?-A biomechanical comparison against miniplates on human specimen.

In this study, topology optimized, patient specific osteosynthesis plates (TOPOS-implants) are evaluated for the mandibular reconstruction using fibula segments. These shape optimized implants are compared to a standard treatment with miniplates (thickness: 1.0 mm, titanium grade 4) in biomechanical testing using human cadaveric specimen.

Thickness measurement via local ultrasonic resonance spectroscopy.

Local ultrasonic resonance spectroscopy (LURS) is a new approach to material inspection, where the specimen is locally excited by a short mechanical impulse while its local mechanical response is recorded at a position nearby. The local material and geometrical properties can be extracted from the frequency spectrum of the response and visualized by performing a scan over the inspected area. In our experiment, the plate thickness and the reliefs of both plate surfaces (plate curvature) were obtained from thickness resonance and time of arrival analysis without physical contact to the specimen.

Full biomechanical mapping of the ovine knee joint to determine creep-recovery, stiffness and thickness variation.

Background: Clinical cartilage repair strategies can be tested using the sheep model as suggest by the European Medicines Agency. To characterize variation within the joint a full biomechanical mapping is necessary. The aim of this study is to establish a loading model, to map regional differences within the knee and determine reference areas for area specific replacement techniques.

Concrete wave dispersion interpretation through Mindlin's strain gradient elastic theory.

Classical elastic wave features like pulse velocity and attenuation have been used for decades for concrete condition characterization. Relatively recently the effect of frequency has been studied showing no doubt over the dispersive behavior of the material. Despite the experimental evidence, there is no unified theory to model the material and explain this phase velocity change at frequencies below 200 kHz.

Time reverse modeling of acoustic emissions in a reinforced concrete beam.

The time reverse modeling (TRM) is applied for signal-based acoustic emission (AE) analysis of reinforced concrete (RC) specimens. TRM uses signals obtained from physical experiments as input. The signals are re-emitted numerically into a structure in a time-reversed manner, where the wavefronts interfere and appear as dominant concentrations of energy at the origin of the AE.

MEMS Microphone Array Sensor for Air-Coupled Impact-Echo.

Impact-Echo (IE) is a nondestructive testing technique for plate like concrete structures. We propose a new sensor concept for air-coupled IE measurements. By using an array of MEMS (micro-electro-mechanical system) microphones, instead of a single receiver, several operational advantages compared to conventional sensing strategies in IE are achieved.

Strategies for reliable automatic onset time picking of acoustic emissions and of ultrasound signals in concrete.

Determining the onset of transient signals like seismograms, acoustic emissions or ultrasound signals is very time consuming if the onset is picked manually. Therefore, different approaches exist, especially in seismology. The concepts of the most popular approaches are summarized.

Evolution of percolating force chains in compressed granular media.

The evolution of effective force chains percolating through a compressed granular system is investigated. We compressed an ensemble of spherical particles monitoring the macroscopic constitutive behavior and the acoustic signals emitted by microscopic rearrangements of particles. We applied the continuous damage model of fiber bundles to describe the evolution of the array of force chains.