Simultaneous wastewater treatment and bioelectricity production in microbial fuel cells using cross-linked chitosan-graphene oxide mixed-matrix membranes.

Microbial fuel cells (MFCs) are emerging technology for wastewater treatment by chemical oxygen demand (COD) reduction and simultaneous bioelectricity production. Fabrication of an effective proton exchange membrane (PEM) is a vital component for MFC performance. In this work, green chitosan-based (CS) PEMs were fabricated with graphene oxide (GO) as filler material (CS-GO) and cross-linked with phosphoric acid (CS-GO-P(24)) or sulfuric acid (CS-GO-S(24)) to determine their effect on PEM properties.

Enhanced surface functionality and microbial fuel cell performance of chitosan membranes through phosphorylation.

The effects of plasticization and cross-linking on the performance of chitosan as promising proton exchange membranes (PEMs) for bioelectricity generation in microbial fuel cells (MFCs) were investigated. The physico-chemical properties of chitosan (CS), sorbitol-chitosan (S-CS), phosphorylated-chitosan (CS-P) and phosphorylated-sorbitol-chitosan (S-CS-P) membranes were investigated by FESEM-EDS, FTIR-ATR, XRD, TGA, tensile strength and sorption studies. The performance of the fabricated PEMs was assessed by power density and cation exchange capacity (CEC).

Elucidating the effects of solar panel waste glass substitution on the physical and mechanical characteristics of clay bricks.

This study deals with the effect of solar panel waste glass on fired clay bricks. Brick samples were heated to temperatures which varied from 700-1000 degrees C for 6 h, with a heating rate of 10 degrees C min(-1). The material properties of the resultant material were then determined, including speciation variation, loss on ignition, shrinkage, bulk density, 24-h absorption rate, compressive strength and salt crystallization.

Resource recovery of scrap silicon solar battery cell.

In order to minimize pollution problems and to conserve limited natural resources, a hydrometallurgical procedure was developed in this study to recover the valuable resources of silicon (Si), silver (Ag) and aluminum (Al) from scrap silicon solar battery cells. In this study, several methods of leaching, crystallization, precipitation, electrolysis and replacement were employed to investigate the recovery efficiency of Ag and Al from defective monocrystalline silicon solar battery cells. The defective solar battery cells were ground into powder followed by composition analysis with inductively coupled plasma-atomic emission spectrometry.

A study on the recycling of scrap integrated circuits by leaching.

In order to minimize the problem of pollution and to conserve limited natural resources, a method to recover the valuable metals such as gold, silver and copper) present in the scrap integrated circuits (ICs) was developed in the present study. Roasting, grinding, screening, magnetic separation, melting and leaching were adopted to investigate the efficiency of recovery of gold, silver and copper from scrap ICs. The collected scrap IC samples were roasted at 850 °C to destroy their plastic resin sealing material, followed by screening and magnetic separation to separate the metals from the resin residue.

Melting of municipal solid waste incinerator fly ash by waste-derived thermite reaction.

This work describes a novel approach for melting municipal solid waste incinerator (MSWI) fly ash, based on self-propagating reactions, by using energy-efficient simulated waste-derived thermite. The self-propagating characteristics, the properties of the recycled alloy and slag and the partitioning of heavy metals during the process are also studied. Experimental results demonstrate that the mix ratio of fly ash to the starting mixture of less than 30% supports the development of the self-propagating reaction with a melting temperature of 1350-2200 degrees C.

Characterizing PAH emission concentrations in ambient air during a large-scale joss paper open-burning event.

Large-scale open burning of joss paper is an important ritual practice for deity worshipping during Buddhist and Taoist festivals. Since Buddhism and Taoism are two of the most popular religions in Chinese societies and some Asian countries, the impact of joss paper burning on the air quality needs further investigation. This study explores the concentrations of polycyclic aromatic hydrocarbons (PAHs) in ambient air during one of the most important festivals, in which large-scale burning of joss paper occurs in temples and in people's houses.

Report: transboundary hazardous waste management. part II: performance auditing of treatment facilities in importing countries.

Before implementing the self-monitoring model programme of the Basel Convention in the Asia, Taiwan has conducted a comprehensive 4-year follow-up project to visit the governmental authorities and waste-disposal facilities in the countries that import waste from Taiwan. A total of nine treatment facilities, six of which are reported in this paper, and the five countries where the plants are located were visited in 2001-2002. France, Belgium and Finland primarily handled polychlorinated biphenyl capacitors, steel mill dust and metal waste.

Transboundary hazardous waste management. Part I: Waste management policy of importing countries.

Mixed metal-containing waste, polychlorinated biphenyls (PCB) containing capacitors, printed circuit boards, steel mill dust and metal sludge were among the most common wastes exported from Taiwan. Before the implementation of the self-monitoring model programme of the Basel Convention (secretariat of the Basel Convention 2001) in the Asia region, Taiwan conducted a comprehensive 4-year follow-up project involving government authorities and the waste disposal facilities of the importing countries. A total of five countries and nine plants were visited in 2001-2002.

An overview of recycling and treatment of scrap computers.

In order to recover valuable materials and to minimize the adverse effects of hazardous materials contained in scrap computers, a dismantling practice is commonly adopted to treat scrap computers. By using the dismantling process, both useful and hazardous materials can be manually separated and retrieved. On the basis of the properties of the retrieved materials, they can be sent to appropriate facilities for further recycling or treatment.

Recycling of scrap cathode ray tubes.

It is estimated that approximately 50% of the weight of a computer monitor is composed of cathode ray tube (CRT) glass. Thus, the successful recycling of scrap CRT glass can greatly relieve the disposal problem created by scrap monitors. CRT glass may be considered a hazardous waste due to its high lead concentration.