Designing Ru-B-Cr Moieties to Activate the Ru Site for Acidic Water Electrolysis under Industrial-Level Current Density.

Developing highly efficient non-iridium-based active sites for acidic water splitting is still a huge challenge. Herein, unique Ru-B-Cr moieties have been constructed in RuO nanofibers (NFs) to activate Ru sites for water electrolysis, which overcomes the bottleneck of RuO-based catalysts usually possessing low activity for the hydrogen evolution reaction (HER) and poor stability for the oxygen evolution reaction (OER). The fabricated Cr, B-doped RuO NFs exhibit low overpotentials of 205 and 379 mV for acidic HER and OER at 1 A cm with outstanding stability lasting 1000 and 188 h, respectively.

Novel Fluorinated Anion Exchange Membranes Based on Poly(Pentafluorophenyl-Carbazole) with High Ionic Conductivity and Alkaline Stability for Fuel Cell Applications.

Constructing good microphase separation structures by designing different polymer backbones and ion-conducting groups is an effective strategy for improving the ionic conductivity and chemical stability of anion exchange membranes (AEMs). In this study, a series of AEMs based on the poly(pentafluorophenylcarbazole) backbone grafted with different cationic groups are designed and prepared to construct well-defined microphase separation morphology and improve the trade-off between the properties of AEMs. Highly hydrophobic fluorinated backbone and alkyl spaces enhance phase separation and construct interconnected hydrophilic channels for anion transport.

Sulfonated Polyimide Membranes Constructed by Main-Chain and Molecular-Network Engineering Strategy for Direct Methanol Fuel Cell.

Excessive swelling is one important factor that leads to high fuel permeability and limited operating concentration of methanol for proton exchange membranes. Herein, a collaborative strategy of main-chain and molecular-network engineering is applied to lower swelling ratio and improve methanol resistance for highly sulfonated polyimide. Two m-phenylenediamine monomers (4-(2,3,5,6-tetrafluoro-4-vinylphenoxy)benzene-1,3-diamine and 4,6-bis(2,3,5,6-tetrafluoro-4-vinylphenoxy)benzene-1,3-diamine) with tetrafluorostyrol groups are designed and synthesized.

Oral Anticoagulation Versus Antiplatelet Treatment After Mitral Valve Repair: A Systematic Review and Meta-Analysis.

Oral anticoagulation with vitamin K antagonists is currently advised for a period of 3 months after surgical mitral valve repair, regardless of the rhythm status. The evidence supporting this recommendation is weak and recent studies have challenged the safety and efficacy of this recommendation. A systematic review of literature was conducted by searching PubMed, Embase, Web of Science, Emcare, and Cochrane Library databases for original publications comparing the efficacy and safety of oral anticoagulation with vitamin K antagonists to antiplatelet treatment early after mitral valve surgery in patients with no atrial fibrillation.

Comparison of the Properties of Epoxy Resins Containing Various Trifluoromethyl Groups with Low Dielectric Constant.

A series of epoxy resins containing various trifluoromethyl groups were synthesized and thermally cured with diaminodiphenylmethane (DDM) and aminophenyl sulfone (DDS). All epoxy resins exhibited excellent thermal stability with the glass transition temperatures of above 128 °C and 5% weight loss temperatures of above 300 °C. DDS-cured epoxy resins possessed higher thermal stability than that of DDM-cured epoxy resins, while DDM-cured epoxy resins showed better mechanical, dielectric, and hydrophobic properties.

Carbonized Polymer Dots Assemble in Proton-Conducting Channels to Enhance the Conductivity and Selectivity Simultaneously for High-Performance Fuel Cells.

Fabricating polymer electrolyte membranes (PEMs) simultaneously with high ion conductivity and selectivity has always been an ultimate goal in many membrane-integrated systems for energy conversion and storage. Constructing broader ion-conducting channels usually enables high-efficient ion conductivity while often bringing increased crossover of other ions or molecules simultaneously, resulting in decreased selectivity. Here, the ultra-small carbon dots (CDs) with the selective barriers are self-assembled within proton-conducting channels of PEMs through electrostatic interaction to enhance the proton conductivity and selectivity simultaneously.

PAEs Derivatives' Design for Insulation: Integrated In-Silico Methods, Functional Assessment and Environmentally Friendly Molecular Modification.

As a common substance in production and life, phthalic acid esters (PAEs), the main component of plastics, have brought more and more serious problems to the environment. This study normalized the insulation, toxicity, and bioconcentration data of 13 PAEs to eliminate the dimensional coefficients of each index, and then used the comprehensive index method to calculate the comprehensive effect value of PAEs with three properties. The comprehensive effect value was used as the data source to construct the 3D-QSAR model of PAE molecular comprehensive effect.

Preparation and evaluation of novel bio-based Bis-GMA-free dental composites with low estrogenic activity.

Objective: Although bisphenol Aglycidyl methacrylate (Bis-GMA) are widely used in the dental composite, its raw materials include the petroleum-based product bisphenol A (BPA) with high estrogenic activity (EA). In this study, two new BPA-free dimethacrylate monomers from bio-based material creosol were synthesized and evaluated.

Methods: The renewable bisphenol monomer 5, 5'-methylenedicreosol (BCF) was prepared from bio-based material creosol.

Construction of Proton Transport Highways Induced by Polarity-Driving in Proton Exchange Membranes to Enhance the Performance of Fuel Cells.

The approach to constructing proton transport channels via direct adjustments, including hydrophilia and analytical acid concentration in hydrophilic domains, has been proved to be circumscribed when encouraging the flatter hydrophilic-hydrophobic microphase separation structures and reducing conductivity activation energy. Here, we propose a constructive solution by regulating the polarity of hydrophobic domains, which indirectly varies the aggregation and connection of hydrophilic ion clusters during membrane formation, enabling orderly self-assembly and homogeneously distributed microphase structures. Accordingly, a series of comb-shaped polymers were synthesized with diversified optimization, and more uniformly distributed ion cluster lattices were subsequently observed using high-resolution transmission electron microscopy.

Intestinal congestion and reperfusion injury: damage caused to the intestinal tract and distal organs.

In clinical practice, intestinal autologous diseases, ailments and organ transplants can cause severe congestive damage to the intestinal tract. However, after the etiological factor is gotten rid of and blood flow is free without any hinderance, further damage to the intestinal wall often occurs, causing other related organ dysfunctions. This ultimately results in intestinal congestion reperfusion injury (ICRI).

Nanostructured high-performance electrolyte membranes based on polymer network post-assembly for high-temperature supercapacitors.

The development of high-temperature supercapacitors highly relies on the explore of stable polymer electrolyte membranes (PEMs) with high ionic conductivities at high-temperature conditions. However, it is a challenge to achieve both high stability and high conductivity in a PEM at elevated temperatures. Herein, we report the fabrication of high-performance proton conductive PEMs suitable for high-temperature supercapacitors (HT-SCs), which is based on a post-assembly strategy to control the rearrangement of polymer networks in the PEMs.

The incorporation of phosphorylated chitosan/amorphous calcium phosphate nanocomplex into an experimental composite resin.

This study evaluated the effect of incorporating phosphorylated chitosan/amorphous calcium phosphate nanocomplex (Pchi/ACP) into an experimental light-cure composite resin on mechanical-chemical properties and human dentin remineralization. The results showed that the mechanical strength and contact angles of the resins decreased with the increase incorporation of Pchi/ACP. Release concentrations of calcium in saline solution were measured at different time points, showing the incorporation of Pchi/ACP significantly increased calcium release within 14 days, and kept steady thereafter.

Theoretical Design of Biodegradable Phthalic Acid Ester Derivatives in Marine and Freshwater Environments.

The biodegradability of phtalic acid esters in marine and freshwater environments was characterized by their binding free energy with corresponding degrading enzymes. According to comprehensive biodegradation effects weights, the binding free energy values were converted into dimensionless efficacy coefficient using ratio normalization method. Then, considering comprehensive dual biodegradation effects value and the structural parameters of PAEs in both marine and freshwater environments, a 3D-QSAR pharmacophore model was constructed, five PAE derivatives (DBP-COOH, DBP-CHO, DBP-OH, DINP-NH, and DINP-NO) were screened out based on their environmental friendliness, functionality and stability.

A Modified 3D-QSAR Model Based on Ideal Point Method and Its Application in the Molecular Modification of Plasticizers with Flame Retardancy and Eco-Friendliness.

The addition of plasticizers makes plastics flammable, and thus, poses a potential risk to the environment. In previous researches, plasticizers with flame retardancy had been synthesized, but their eco-friendliness had not been tested or described. Thus, in this paper, eco-friendliness plasticizers with flame retardancy were designed based on phthalic acid esters (PAEs), which are known as common plasticizers and major plastic additives.

Enhanced Biodegradation of Phthalic Acid Esters' Derivatives by Plasticizer-Degrading Bacteria (, , ) Using a Correction 3D-QSAR Model.

A phthalic acid ester's (PAEs) comprehensive biodegradability three-dimensional structure-activity relationship (3D-QSAR) model was established, to design environmentally friendly PAE derivatives, which could be simultaneously degraded by plasticizer-degrading bacteria, such as , , and . Only three derivatives of diethyl phthalate (DEP (DEP-27, DEP-28 and DEP-29)) were suited for their functionality and environmental friendliness, which had an improved stability in the environment and improved the characteristics (bio-toxicity, bioaccumulation, persistence, and long-range migration) of the persistent organic pollutants (POPs). The simulation inference of the microbial degradation path before and after DEP modification and the calculation of the reaction energy barrier exhibited the energy barrier for degradation being reduced after DEP modification and was consistent with the increased ratio of comprehensive biodegradability.

Preparation of a Cross-Linked Sulfonated Poly(arylene ether ketone) Proton Exchange Membrane with Enhanced Proton Conductivity and Methanol Resistance by Introducing an Ionic Liquid-Impregnated Metal Organic Framework.

A novel ionic liquid-impregnated metal-organic-framework (IL@NH-MIL-101) was prepared and introduced into sulfonated poly(arylene ether ketone) with pendent carboxyl groups (SPAEK) as the nanofiller for achieving hybrid proton exchange membranes. The nanofiller was anchored in the polymeric matrix by the formation of amido linkage between the pendent carboxyl group attached to the molecule chain of SPAEK and amino group belonging to the inorganic framework, thus leading to the enhancement in mechanical properties and dimensional stability. Besides, the hybrid membrane (IL@MOF-1) exhibits an enhanced proton conductivity up to 0.

A comparative study of side-chain-type poly(ether ether ketone) anion exchange membrane functionalized with different hetero-cycloaliphatic quaternary ammonium groups.

Anion exchange membranes based on side-chain-type quarternized poly(ether ether ketone)s (QPEEKs), containing different hetero-cycloaliphatic quaternary ammonium groups, were prepared a multi-step procedure, including polycondensation with a monomer containing pendant methylphenyl groups, bromomethylation, and followed by quaternization with 1-methylpyrrolidine (MPY), 1-methylpiperidine (MPRD), 1-methylimidazole (MIDZ) and -methyl morpholine (MMPH), respectively. The properties of these membranes were then compared with the properties of conventional quarternized poly(ether ether ketone)s containing benzyltrimethylammonium (QPEEK-TMA). Model compounds, QMPY, QMPRD, QMIDZ and QMMPH, were synthesized and used to quantitatively compare the alkaline stability of hetero-cycloaliphatic quaternary ammonium groups using H NMR.

Enhanced Proton Conductivity of Sulfonated Hybrid Poly(arylene ether ketone) Membranes by Incorporating an Amino-Sulfo Bifunctionalized Metal-Organic Framework for Direct Methanol Fuel Cells.

Novel side-chain-type sulfonated poly(arylene ether ketone) (SNF-PAEK) containing naphthalene and fluorine moieties on the main chain was prepared in this work, and a new amino-sulfo-bifunctionalized metal-organic framework (MNS, short for MIL-101-NH-SOH) was synthesized via a hydrothermal technology and postmodification. Then, MNS was incorporated into a SNF-PAEK matrix as an inorganic nanofiller to prepare a series of organic-inorganic hybrid membranes (MNS@SNF-PAEK-XX). The mechanical property, methanol resistance, electrochemistry, and other properties of MNS@SNF-PAEK-XX hybrid membranes were characterized in detail.

Preparation and characterization of silane-modified SiO particles reinforced resin composites with fluorinated acrylate polymer.

A series of fluorinated dental resin composites were prepared with two kinds of SiO particles. Bis-GMA (bisphenol A-glycerolate dimethacrylate)/4-TF-PQEA (fluorinated acrylate monomer)/TEGDMA (triethylene glycol dimethacrylate) (40/30/30, wt/wt/wt) was introduced as resin matrix. SiO nanopartices (30nm) and SiO microparticles (0.

Synthesis, characterization and evaluation of a fluorinated resin monomer with low water sorption.

A fluorinated acrylate monomer (4-TF-PQEA) without BPA (bisphenol-A) structure was synthesized and mixed with triethylene glycol dimethacrylate (TEGDMA) to used as dental resin system in order to achieve lower water sorption and reduce human exposure to BPA derivatives. Double bond conversion (DC) was measured using Fourier transform infrared spectroscopy (FTIR). Water sorption (WS), water solution (WL) and depth of cure (DOC) were evaluated according to ISO 4049:2009.

Property Enhancement Effects of Side-Chain-Type Naphthalene-Based Sulfonated Poly(arylene ether ketone) on Nafion Composite Membranes for Direct Methanol Fuel Cells.

Nafion/SNPAEK-x composite membranes were prepared by blending raw Nafion and synthesized side-chain-type naphthalene-based sulfonated poly(arylene ether ketone) with a sulfonation degree of 1.35 (SNPAEK-1.35).

Inorganic-Macroion-Induced Formation of Bicontinuous Block Copolymer Nanocomposites with Enhanced Conductivity and Modulus.

A facile and electrostatically driven approach has been developed to prepare bicontinuous polymer nanocomposites that is based on the polyoxometalate (POM) macroion induced phase transition of PS-b-P2VP from an initial lamellar phase to a stable bicontinuous phase. The multi-charged POMs can electrostatically cross-link P2VP blocks and give rise to bicontinuous phases in which the POM hybrid conductive domains occupy a large volume fraction of more than 50 %. Furthermore, the POMs can give rise to high proton conductivity and serve as nanoenhancers, endowing the bicontinuous nanocomposites with a conductivity of 0.