Surface reconstruction of wide-bandgap perovskites enables efficient perovskite/silicon tandem solar cells.

Wide-bandgap perovskite solar cells (WBG-PSCs) are critical for developing perovskite/silicon tandem solar cells. The defect-rich surface of WBG-PSCs will lead to severe interfacial carrier loss and phase segregation, deteriorating the device's performance. Herein, we develop a surface reconstruction method by removing the defect-rich crystal surface by nano-polishing and then passivating the newly exposed high-crystallinity surface.

Cross-Linkable Fullerene Electron Transport Layer with Internal Encapsulation Capability for Efficient and Stable Inverted Perovskite Solar Cells.

A stable and compact fullerene electron transport layer (ETL) is crucial for high-performance inverted perovskite solar cells (PSCs). However, traditional fullerene-based ETLs like C and PCBM are prone to aggregate under operational conditions, a challenge recently recognized by academic and industrial researchers. Here, we designed and synthesized a novel cross-linkable fullerene molecule, bis((3-methyloxetan-3-yl)methyl) malonate-C monoadduct (BCM), for use as an ETL in PSCs.

Multidentate Fullerenes Enable Tunable and Robust Interfacial Bonding for Efficient Tin-Based Perovskite Solar Cells.

Improving the efficiency of tin-based perovskite solar cells (TPSCs) is significantly hindered by energy level mismatch and weak interactions at the interface between the tin-based perovskite and fullerene-based electron transport layers (ETLs). In this study, four well-defined multidentate fullerene molecules with 3, 4, 5, and 6 diethylmalonate groups, labeled as FM3, FM4, FM5, and FM6 are synthesized, and employed as interfacial layers in TPSCs. It is observed that increasing the number of functional groups in these fullerenes leads to shallower lowest unoccupied molecular orbital (LUMO) energy levels and enhance interfacial chemical interactions.

Efficient and Stable Inverted Perovskite Solar Cells Enabled by a Fullerene-Based Hole Transport Molecule.

Designing an efficient modification molecule to mitigate non-radiative recombination at the NiO/perovskite interface and improve perovskite quality represents a challenging yet crucial endeavor for achieving high-performance inverted perovskite solar cells (PSCs). Herein, we synthesized a novel fullerene-based hole transport molecule, designated as FHTM, by integrating C with 12 carbazole-based moieties, and applied it as a modification molecule at the NiO/perovskite interface. The in situ self-doping effect, triggered by electron transfer between carbazole-based moiety and C within the FHTM molecule, along with the extended π conjugated moiety of carbazole groups, significantly enhances FHTM's hole mobility.

Efficient and Stable Monolithic Perovskite/Silicon Tandem Solar Cells Enabled by Contact-Resistance-Tunable Indium Tin Oxide Interlayer.

The imperfect charge behavior at the interfaces of perovskite/electron-transport layer (ETL)/transparent conducting oxide (TCO) limits the further performance improvement of perovskite/silicon tandem solar cells. Herein, an indium tin oxide interlayer is deposited between ETL and TCO to address this issue. Specifically, the interlayer is prepared using an all-physical and HO-free method, electron-beam evaporation, which can avoid any potential damage to the underlying perovskite and ETL layers.

Surface Treatment with Tailored π-Conjugated Fluorene Derivatives Significantly Enhances the Performance of Perovskite Light-Emitting Diodes.

Surface defect passivation and carrier injection regulation have emerged as effective strategies for enhancing the performance of perovskite light-emitting diodes (Pero-LEDs). It usually requires two functional molecules to realize defect passivation and carrier injection regulation separately. In other words, developing one single molecule possessing these capabilities remains challenging.

Cross-Linkable Fullerene Enables Elastic and Conductive Grain Boundaries for Efficient and Wearable Tin-Based Perovskite Solar Cells.

Tin-based perovskite solar cells (TPSCs) have received increasing attention due to their low toxicity, high theoretical efficiency, and potential applications as wearable devices. However, the inherent fast and uncontrollable crystallization process of tin-based perovskites results in high defect density in the film. Meanwhile, when fabricated into flexible devices, the prepared perovskite film exhibits inevitable brittleness and high Young's modulus, seriously weakening the mechanical stability.

Suppressing Halide Segregation via Pyridine-Derivative Isomers Enables Efficient 1.68 eV Bandgap Perovskite Solar Cells.

Light-induced phase segregation is one of the main issues restricting the efficiency and stability of wide-bandgap perovskite solar cells (WBG PSCs). Small organic molecules with abundant functional groups can passivate various defects, and therefore suppress the ionic migration channels for phase segregation. Herein, a series of pyridine-derivative isomers containing amino and carboxyl are applied to modify the perovskite surface.

Efficient Tin-Based Perovskite Solar Cells Enabled by Precisely Synthesized Single-Isomer Fullerene Bisadducts with Regulated Molecular Packing.

Designing and synthesizing fullerene bisadducts with a higher-lying conduction band minimum is promising to further improve the device performance of tin-based perovskite solar cells (TPSCs). However, the commonly obtained fullerene bisadduct products are isomeric mixtures and require complicated separation. Moreover, the isomeric mixtures are prone to resulting in energy alignment disorders, interfacial charge loss, and limited device performance improvement.

Ion-Diffusion Management Enables All-Interface Defect Passivation of Perovskite Solar Cells.

Perovskite solar cells (PSCs) have demonstrated over 25% power conversion efficiency (PCE) via efficient surface passivation. Unfortunately, state-of-the-art perovskite post-treatment strategies can solely heal the top interface defects. Herein, an ion-diffusion management strategy is proposed to concurrently modulate the top interfaces, buried interfaces, and bulk interfaces (i.

Dissolved-Cl triggered redox reaction enables high-performance perovskite solar cells.

Constructing 2D/3D perovskite heterojunctions is effective for the surface passivation of perovskite solar cells (PSCs). However, previous reports that studying perovskite post-treatment only physically deposits 2D perovskite on the 3D perovskite, and the bulk 3D perovskite remains defective. Herein, we propose Cl-dissolved chloroform as a multifunctional solvent for concurrently constructing 2D/3D perovskite heterojunction and inducing the secondary growth of the bulk grains.

Phase Regulation and Defect Passivation Enabled by Phosphoryl Chloride Molecules for Efficient Quasi-2D Perovskite Light-Emitting Diodes.

The modification of perovskite precursor by a series of phosphoryl chloride molecules can indeed improve the performance of perovskite LEDs (Pero-LEDs). The bis(2-oxo-3-oxazolidinyl) phosphinic chloride can not only regulate the phase distribution by controlling the crystallization rate but also passivate the defects of the quasi-2D perovskite. Highly efficient and reproducible Pero-LEDs are achieved with an maximum external quantum efficiency (EQE) of 20.

Efficient Semi-Transparent Wide-Bandgap Perovskite Solar Cells Enabled by Pure-Chloride 2D-Perovskite Passivation.

Wide-bandgap (WBG) perovskite solar cells suffer from severe non-radiative recombination and exhibit relatively large open-circuit voltage (V) deficits, limiting their photovoltaic performance. Here, we address these issues by in-situ forming a well-defined 2D perovskite (PMA)PbCl (phenmethylammonium is referred to as PMA) passivation layer on top of the WBG active layer. The 2D layer with highly pure dimensionality and halide components is realized by intentionally tailoring the side-chain substituent at the aryl ring of the post-treatment reagent.

Well-Defined Fullerene Bisadducts Enable High-Performance Tin-Based Perovskite Solar Cells.

Tin-based perovskite solar cells (TPSCs) are attracting intense research interest due to their excellent optoelectric properties and eco-friendly features. To further improve the device performance, developing new fullerene derivatives as electron transporter layers (ETLs) is highly demanded. Four well-defined regioisomers (trans-2, trans-3, trans-4, and e) of diethylmalonate-C bisadduct (DCBA) are isolated and well characterized.

Moisture-triggered fast crystallization enables efficient and stable perovskite solar cells.

Understanding the function of moisture on perovskite is challenging since the random environmental moisture strongly disturbs the perovskite structure. Here, we develop various N-protected characterization techniques to comprehensively study the effect of moisture on the efficient cesium, methylammonium, and formamidinium triple-cation perovskite (CsFAMA)Pb(IBr). In contrast to the secondary measurements, the established air-exposure-free techniques allow us directly monitor the influence of moisture during perovskite crystallization.

Fullerene Derivative with Flexible Alkyl Chain for Efficient Tin-Based Perovskite Solar Cells.

Fullerene derivatives are considered excellent materials for the extraction and transportation of electrons in the production of efficient tin-based perovskite solar cells (TPSCs). However, it is not clear how the molecular structure of fullerene derivatives affects the efficiency and stability of TPSCs. In this study, the effects of fullerene derivatives, (6,6)-phenyl-C-butyric acid hexyl ester (PCBH) and (6,6)-phenyl-C-butyric acid methyl ester (PCBM), with different functional groups, on photovoltaic performance were investigated.

Efficient and stable inverted perovskite solar cells enabled by inhibition of self-aggregation of fullerene electron-transporting compounds.

Fullerene-based electron-transporting layers (ETLs) significantly influence the defect passivation and device performance of inverted perovskite solar cells (PSCs). However, the π-cage structures of fullerenes lead to a strong tendency to self-aggregate, which affects the long-term stability of the corresponding PSCs. Experimental results revealed that [6,6]-phenyl-C-butyric acid methyl ester (PCBM)-based ETLs exhibit a certain degree of self-aggregation that affects the stability of the device, particularly under continuous irradiation stress.

Guanine-Stabilized Formamidinium Lead Iodide Perovskites.

Formamidinium (FA) lead iodide perovskite materials feature promising photovoltaic performances and superior thermal stabilities. However, conversion of the perovskite α-FAPbI phase to the thermodynamically stable yet photovoltaically inactive δ-FAPbI phase compromises the photovoltaic performance. A strategy is presented to address this challenge by using low-dimensional hybrid perovskite materials comprising guaninium (G) organic spacer layers that act as stabilizers of the three-dimensional α-FAPbI phase.

Efficient and Stable Low-Bandgap Perovskite Solar Cells Enabled by a CsPbBr-Cluster Assisted Bottom-up Crystallization Approach.

Recently, low-bandgap formamidinium lead iodide FAPbI-based perovskites are of particular interest for high-performance perovskite solar cells (PSCs) due to their broad spectral response and high photocurrent output. However, to inhibit the spontaneous α-to-δ phase transition, 15-17% (molar ratio) of bromide and cesium or methylammonium incorporated into the FAPbI are indispensable to achieve efficient PSCs. In return, the high bromide content will increase bandgap and narrow the spectral response region.

A Multifunctional Bis-Adduct Fullerene for Efficient Printable Mesoscopic Perovskite Solar Cells.

Printable mesoscopic perovskite solar cells (PMPSCs) have exhibited great attractive prospects in the energy conversion field due to their high stability and potential scalability. However, the thick perovskite film in the mesoporous layers challenges the charge transportation and increase grain boundary defects, limiting the performance of the PMPSCs. It is critical not only to improve the electric property of the perovskite film but also to passivate the charge traps to improve the device performance.

Boron-Doped Graphite for High Work Function Carbon Electrode in Printable Hole-Conductor-Free Mesoscopic Perovskite Solar Cells.

Work function of carbon electrodes is critical in obtaining high open-circuit voltage as well as high device performance for carbon-based perovskite solar cells. Herein, we propose a novel strategy to upshift work function of carbon electrode by incorporating boron atom into graphite lattice and employ it in printable hole-conductor-free mesoscopic perovskite solar cells. The high-work-function boron-doped carbon electrode facilitates hole extraction from perovskite as verified by photoluminescence.

Improved Performance and Stability of Inverted Planar Perovskite Solar Cells Using Fulleropyrrolidine Layers.

Inverted planar structure perovskite solar cells (PSCs), due to their low-temperature precessing and lack of hysteretic problems, are attracting increased attention by researchers around the world. Fullerene derivatives are the most widely used electron transport materials (ETMs) in inverted planar perovskite solar cells, especially [6,6]-phenyl-C-butyric acid methylester (PCBM), which exhibits very good performance. However, to the best of our knowledge, the influence of adducts on fullerene-based PSCs performance has not been fully explored to date.

Formation of Curvature Subunit of Carbon in Combustion.

Curvature prevalently exists in the world of carbon materials (e.g., fullerenes, buckyl bowls, carbon nanotubes, and onions), but traditional C2-addition mechanisms fail to elucidate the mechanism responsible for the formation of carbon curvature starting from a pentagonal carbon ring in currently available chemical-physical processes such as combustion.