Cryo-focused ion beam preparation of perovskite based solar cells for atom probe tomography.

Focused-ion beam lift-out and annular milling is the most common method used for obtaining site specific specimens for atom probe tomography (APT) experiments and transmission electron microscopy. However, one of the main limitations of this technique comes from the structural damage as well as chemical degradation caused by the beam of high-energy ions. These aspects are especially critical in highly-sensitive specimens.

Steering the Properties of MoOx Hole Transporting Layers in OPVs and OLEDs: Interface Morphology vs. Electronic Structure.

The identification, fine-tuning, and process optimization of appropriate hole transporting layers (HTLs) for organic solar cells is indispensable for the production of efficient and sustainable functional devices. In this study, the optimization of a solution-processed molybdenum oxide (MoOx) layer fabricated from a combustion precursor is carried out via the introduction of zirconium and tin additives. The evaluation of the output characteristics of both organic photovoltaic (OPV) and organic light emitting diode (OLED) devices demonstrates the beneficial influence upon the addition of the Zr and Sn ions compared to the generic MoOx precursor.

Band Gap Tuning via Lattice Contraction and Octahedral Tilting in Perovskite Materials for Photovoltaics.

Tin and lead iodide perovskite semiconductors of the composition AMX, where M is a metal and X is a halide, are leading candidates for high efficiency low cost tandem photovoltaics, in part because they have band gaps that can be tuned over a wide range by compositional substitution. We experimentally identify two competing mechanisms through which the A-site cation influences the band gap of 3D metal halide perovskites. Using a smaller A-site cation can distort the perovskite lattice in two distinct ways: by tilting the MX octahedra or by simply contracting the lattice isotropically.

Structure-Property Relations of Methylamine Vapor Treated Hybrid Perovskite CHNHPbI Films and Solar Cells.

The power conversion efficiency of halide perovskite solar cells is heavily dependent on the perovskite layer being sufficiently smooth and pinhole-free. It has been shown that these features can be obtained even when starting out from rough and discontinuous perovskite film by briefly exposing the film to methylamine (MA) vapor. The exact underlying physical mechanisms of this phenomenon are, however, still unclear.

Perovskite-perovskite tandem photovoltaics with optimized band gaps.

We demonstrate four- and two-terminal perovskite-perovskite tandem solar cells with ideally matched band gaps. We develop an infrared-absorbing 1.2-electron volt band-gap perovskite, FACsSnPbI, that can deliver 14.

A Universal Deposition Protocol for Planar Heterojunction Solar Cells with High Efficiency Based on Hybrid Lead Halide Perovskite Families.

A robust and expedient gas quenching method is developed for the solution deposition of hybrid perovskite thin films. The method offers a reliable standard practice for the fabrication of a non-exhaustive variety of perovskites exhibiting excellent film morphology and commensurate high performance in both regular and inverted structured solar cell architectures.

Assessing the toxicity of Pb- and Sn-based perovskite solar cells in model organism Danio rerio.

Intensive development of organometal halide perovskite solar cells has lead to a dramatic surge in power conversion efficiency up to 20%. Unfortunately, the most efficient perovskite solar cells all contain lead (Pb), which is an unsettling flaw that leads to severe environmental concerns and is therefore a stumbling block envisioning their large-scale application. Aiming for the retention of favorable electro-optical properties, tin (Sn) has been considered the most likely substitute.

Segregation versus colocalization: orthogonally functionalized binary micropatterned substrates regulate the molecular distribution in focal adhesions.

Orthogonally functionalized binary micropatterned substrates are produced using a novel protocol. The use of adequate peptido-mimetics enables an unprecedented segregation of purified αvβ3 and α5β1 integrins in adjacent microislands and evidences the preference of U2OS cells to colocalize such receptors. Moreover, this tendency can be altered by varying the geometry and composition of the micropatterns.

Nafion-modified MoOx as effective room-temperature hole injection layer for stable, high-performance inverted organic solar cells.

We present a hole injection layer processed from solution at room temperature for inverted organic solar cells. Bis(2,4-pentanedionato) molybdenum(VI) dioxide (MoO2(acac)2) is used as the precursor for MoOx. Small amounts of Nafion in the precursor solution allow it to form continuous films with good wetting onto the active layers.

Ultrathin ammonium heptamolybdate films as efficient room-temperature hole transport layers for organic solar cells.

Ammonium heptamolybdate (NH4)6Mo7O24·4H2O (AHM) and its peroxo derivatives are analyzed as solution-processed room temperature hole transport layer (HTL) in organic solar cells. Such AHM based HTLs are investigated in devices with three different types of active layers, i.e.

Perovskite-based hybrid solar cells exceeding 10% efficiency with high reproducibility using a thin film sandwich approach.

Organometal halide perovskites have tremendous potential as light absorbers for photovoltaic applications. In this work we demonstrate hybrid solar cells based on the mixed perovskite CH3 NH3 PbI2 Cl in a thin film sandwich structure, with unprecedented reproducibility and generating efficiencies up to 10.8%.

A molecular toolkit for the functionalization of titanium-based biomaterials that selectively control integrin-mediated cell adhesion.

We present a click chemistry-based molecular toolkit for the biofunctionalization of materials to selectively control integrin-mediated cell adhesion. To this end, α5β1-selective RGD peptidomimetics were covalently immobilized on Ti-based materials, and the capacity to promote the selective binding of α5β1 was evaluated using a solid-phase integrin binding assay. This functionalization strategy yielded surfaces with a nine-fold increased affinity for α5β1, in comparison to control samples, and total selectivity against the binding of the closely related integrin αvβ3.

Tuning the dimensions of ZnO nanorod arrays for application in hybrid photovoltaics.

ZnO nanorod arrays are a very eligible option as electron acceptor material in hybrid solar cells, owing to their favorable electrical properties and abundance of available, easy, and low-cost synthesis methods. To become truly effective in this field, a major prerequisite is the ability to tune the nanorod dimensions towards optimal compatibility with electron-donating absorber materials. In this work, a water-based seeding and growth procedure is used to synthesize ZnO nanorods.