Microstructure and coupling mechanisms in MnBi-FeSiB nanocomposites obtained by spark plasma sintering.

Fabrication and extensive characterization of hard-soft nanocomposites composed of hard magnetic low-temperature phase LTP-MnBi and amorphous FeSiB soft magnetic phase for bulk magnets are reported. Samples with compositions MnBi + x⋅(FeSiB) (x = 0, 3, 5, 10, 20 wt.%) were prepared by spark plasma sintering of powder mixtures.

Biocompatible Composite Filaments Printable by Fused Deposition Modelling Technique: Selection of Tuning Parameters by Influence of Biogenic Hydroxyapatite and Graphene Nanoplatelets Ratios.

The proposed strategy for the extrusion of printable composite filaments follows the favourable association of biogenic hydroxyapatite (HA) and graphene nanoplatelets (GNP) as reinforcement materials for a poly(lactic acid) (PLA) matrix. HA particles were chosen in the <40 μm range, while GNP were selected in the micrometric range. During the melt-mixing incorporation into the PLA matrix, both reinforcement ratios were simultaneously modulated for the first time at different increments.

Influence of Ceramic Particles Size and Ratio on Surface-Volume Features of the Naturally Derived HA-Reinforced Filaments for Biomedical Applications.

The intersection of the bone tissue reconstruction and additive manufacturing fields promoted the advancement to a prerequisite and new feedstock resource for high-performance bone-like-scaffolds manufacturing. In this paper, the proposed strategy was directed toward the use of bovine-bone-derived hydroxyapatite (HA) for surface properties enhancement and mechanical features reinforcement of the poly(lactic acid) matrix for composite filaments extrusion. The involvement of completely naturally derived materials in the technological process was based on factors such as sustainability, low cost, and a facile and green synthesis route.

Macroscopic Electromagnetic Cooperative Network-Enhanced MXene/Ni Chains Aerogel-Based Microwave Absorber with Ultra-Low Matching Thickness.

Electromagnetic cooperative strategy has been presented as a mainstream approach that can effectively optimize the matching thickness of dielectric loss dominant system. However, it is still challenging for dielectric-magnetic loss coexisting-type absorber to develop electromagnetic wave (EMW) performance with ultra-low matching thickness (≤ 1 mm). Breaking the limitation of traditional electromagnetic response at microscopic/mesoscopic scale, a ficus microcarpa-like magnetic aerogel with macroscopical electromagnetic cooperative effect was fabricated through highly oriented self-assembly engineering.

Assessment of Hot Corrosion in Molten NaSO and VO of Inconel 625 Fabricated by Selective Laser Melting versus Conventional Technology.

Inconel 625 samples, obtained by Selective Laser Melting (SLM) and conventional technology, were tested for hot corrosion resistance against a molten mixture of NaSO and VO. The assessments were performed in air, at 900 °C with exposure time of up to 96 h, and at 1000 °C for 8 h. Weight gain was higher for samples obtained by SLM, with 37.

Second magnetization peak, rhombic-to-square Bragg vortex glass transition, and intersecting magnetic hysteresis curves in overdoped BaFe(AsP) single crystals.

The second magnetization peak (SMP) in the fourfold symmetric superconducting single crystals (such as iron pnictides and tetragonal cuprates) has been attributed to the rhombic-to-square transition (RST) of the quasi-ordered vortex solid (the Bragg vortex glass, BVG). This represents an alternative to the pinning-induced BVG disordering as the actual SMP mechanism. The analysis of the magnetic response of BaFe(AsP) specimens presented here shows that the SMP is not generated by the RST.

Reproducibility of small GeCHO-added MgB bulks fabricated by ex situ Spark Plasma Sintering used in compound bulk magnets with a trapped magnetic field above 5 T.

Bulk discs (20 mm diameter and 4.3 mm thickness) of MgB added with GeCHO were obtained by Spark Plasma Sintering. Six samples with composition MgB(GeCHO) and one undoped sample were fabricated under similar conditions and were magnetically characterized in order to determine the scattering of properties and reproducibility.

Morpho-Structural, Thermal and Mechanical Properties of PLA/PHB/Cellulose Biodegradable Nanocomposites Obtained by Compression Molding, Extrusion, and 3D Printing.

Biodegradable blends and nanocomposites were produced from polylactic acid (PLA), poly(3-hydroxybutyrate) (PHB) and cellulose nanocrystals (NC) by a single step reactive blending process using dicumyl peroxide (DCP) as a cross-linking agent. With the aim of gaining more insight into the impact of processing methods upon the morphological, thermal and mechanical properties of these nanocomposites, three different processing techniques were employed: compression molding, extrusion, and 3D printing. The addition of DCP improved interfacial adhesion and the dispersion of NC in nanocomposites as observed by scanning electron microscopy and atomic force microscopy.

Evaluation of pristine and Eu ₂O₃-added MgB ₂ ceramics for medical applications: hardness, corrosion resistance, cytotoxicity and antibacterial activity.

Nano- or micropowders of Eu2O3 were added to MgB2, resulting in a composition of (MgB2)0.975(EuO1.5)0.