Scanning electrochemical microscopy, 52. Bipolar conductance technique at ultramicroelectrodes for resistance measurements.

The bipolar conductance, BICON, technique for the measurement of solution resistance, based on the application of microsecond current pulses, as originally described by Enke and co-workers for measurements with conventional electrodes, was extended for use with ultramicroelectrodes, with a focus on its application in scanning electrochemical microscopy (SECM). When the plateau time used to make the measurement lies within the BICON conditions, the solution conductance can be obtained directly from the output without the need for calibration curves. However, decreasing the size of the ultramicroelectrode decreases the range of values that satisfy these conditions, and one must resort to calibration curves to obtain solution conductance from the measured current, which was nevertheless found to be proportional to electrolyte concentration with electrodes as small as 5 mum in diameter.

Electrogenerated chemiluminescence. 77. DNA hybridization detection at high amplification with [Ru(bpy)3]2+-containing microspheres.

An ultrasensitive DNA hybridization detection method based on electrogenerated chemiluminescence (ECL) using polystyrene microspheres/beads (PSB) as the carrier of the ECL labels, namely, tris(2,2'-bipyridyl)ruthenium(II) tetrakis(pentafluorophenyl)borate (Ru(bpy)3[B(C6F5)4]2), is reported. Probe single-stranded DNA (p-ssDNA) was attached to the surface of magnetic beads (MB) and hybridized with target-ssDNA (t-ssDNA) with immobilized PSB containing a large number of water insoluble Ru(bpy)3[B(C6F5)4]2 species (approximately 7.5 x 10(9) molecules/bead).

Strong blue photoluminescence and ECL from OH-terminated PAMAM dendrimers in the absence of gold nanoparticles.

A product showing strong blue photoluminescence was obtained by oxidation of OH-terminated PAMAM dendrimers, such as G4-OH, G2-OH, and G0-OH, with HAuCl4 or (NH4)2S2O8. The fluorescence emission spectrum peaked at 450 nm, while the excitation maximum was at 380 nm, independent of the generation of dendrimer. The product also shows two weak electrogenerated chemiluminescence (ECL) signals upon cycling the potential between about 1.

Scanning electrochemical microscopy: theory and characterization of electrodes of finite conical geometry.

Finite conical electrodes, which are of particular interest as probes for imaging of surfaces using scanning electrochemical microscopy (SECM), in kinetic studies and in probing thin films were investigated. Theoretical SECM tip current-distance feedback (approach) curves for a finite conical electrode were calculated by numerical (finite element) analysis and compared to an earlier approximate model. The SECM curves obtained depended on the ratio of the base radius of the cone to the height of the cone and on the thickness of the insulating sheath.

Scanning electrochemical microscopy of menadione-glutathione conjugate export from yeast cells.

The uptake of menadione (2-methyl-1,4-naphthoquinone), which is toxic to yeast cells, and its expulsion as a glutathione complex were studied by scanning electrochemical microscopy. The progression of the in vitro reaction between menadione and glutathione was monitored electrochemically by cyclic voltammetry and correlated with the spectroscopic (UV-visible) behavior. By observing the scanning electrochemical microscope tip current of yeast cells suspended in a menadione-containing solution, the export of the conjugate from the cells with time could be measured.

Scanning electrochemical microscopy 50. Kinetic study of electrode reactions by the tip generation-substrate collection mode.

A scanning electrochemical microscopy (SECM) methodology for localized quantitative kinetic studies of electrode reactions based on the tip generation-substrate collection (TG-SC) operation mode is presented. This approach does not use the mediator feedback required in typical kinetic SECM experiments. The reactant is galvanostatically electrogenerated on a tip placed in proximity to the substrate.

Structure-dependent charge transport and storage in self-assembled monolayers of compounds of interest in molecular electronics: effects of tip material, headgroup, and surface concentration.

The electrical properties of self-assembled monolayers (SAMs) on a gold surface have been explored to address the relation between the conductance of a molecule and its electronic structure. We probe interfacial electron transfer processes, particularly those involving electroactive groups, of SAMs of thiolates on Au by using shear force-based scanning probe microscopy (SPM) combined with current-voltage (i-V) and current-distance (i-d) measurements. Peak-shaped i-V curves were obtained for the nitro- and amino-based SAMs studied here.

Electrons are transported through phenylene-ethynylene oligomer monolayers via localized molecular orbitals.

We report excellent correlations between the first negative threshold potentials (V(TH)s) for electric conduction, electrochemical potentials, and computed lowest unoccupied molecular orbital energies in a series of phenylene-ethynylene oligomers bearing a sulfur-based anchoring unit and different electroactive substituents on the central benzene ring. The theoretical and electrochemical results strongly suggest that the peaks observed in the i-V curves have a true molecular origin and are associated with distinct unoccupied molecular levels of the compounds that are strongly localized on the central ring (except for compound I). This localization might account for the existence of a long-lived radical-anion state that permits lateral electron hopping and leads to charge trapping and storage.

Electron transfer at self-assembled monolayers measured by scanning electrochemical microscopy.

New approaches have been developed for measuring the rates of electron transfer (ET) across self-assembled molecular monolayers by scanning electrochemical microscopy (SECM). The developed models can be used to independently measure the rates of ET mediated by monolayer-attached redox moieties and direct ET through the film as well as the rate of a bimolecular ET reaction between the attached and dissolved redox species. By using a high concentration of redox mediator in solution, very fast heterogeneous (10(8) s(-1)) and bimolecular (10(11) mol(-1) cm(3) s(-1)) ET rate constants can be measured.

Oxygen is electroreduced to water on a "wired" enzyme electrode at a lesser overpotential than on platinum.

The first enzyme-based catalyst that is superior to platinum in the four-electron electroreduction of oxygen to water is reported. The smooth Pt cathode reached half and 90% of the mass transport-limited current density at respective overpotentials of -0.4 and -0.

Electrogenerated chemiluminescence. 72. Determination of immobilized DNA and C-reactive protein on Au(111) electrodes using tris(2,2'-bipyridyl)ruthenium(II) labels.

Anodic electrogenerated chemiluminescence (ECL) with tri-n-propylamine (TPrA) as a coreactant was used to determine DNA and C-reactive protein (CRP) by immobilizations on Au(111) electrodes using tris(2,2'-bipyridyl)ruthenium(II) (Ru(bpy)(3)(2+)) labels. A 23-mer synthetic single-stranded (ss) DNA derived from the Bacillus anthracis with an amino-modified group at the 5' end position was covalently attached to the Au(111) substrate precoated with a self-assembled thiol monolayer of 3-mercaptopropanoic acid (3-MPA) in the presence of 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide hydrochloride (EDAC) and then hybridized with a target ssDNA tagged with Ru(bpy)(3)(2+) ECL labels. Similarly, biotinylated anti-CRP species were immobilized effectively onto the Au(111) substrate precovered with a layer of avidin linked covalently via the reaction between avidin and a mixed thiol monolayer of 3-MPA and 16-mercaptohexadecanoic acid on Au(111) in the presence of EDAC and N-hydroxysuccinimide.

Scanning electrochemical microscopy. 48. Hg/Pt hemispherical ultramicroelectrodes: fabrication and characterization.

Hg/Pt hemispherical ultramicroelectrodes (UMEs) (25-microm diameter) were prepared either by electrodeposition from a mercuric ion solution or by simple contact of the Pt disk to a hanging mercury drop electrode. The two methods produced equivalent tips. Optical inspection and electrochemical characterization of these Hg tips with methyl viologen, cobalt sepulchrate trichloride, and hexamineruthenium(III) chloride confirm the hemispherical nature of the UME.

Synthesis, cyclic voltammetric studies, and electrogenerated chemiluminescence of a new phenylquinoline-biphenothiazine donor-acceptor molecule.

We report the synthesis, electrochemistry, and luminescence of a novel ECL emitting compound containing two electron-accepting hexyl-phenylquinoline groups covalently attached to the 3,3'-positions of the electron-donating 10,10'-dimethylbiphenothiazine group. The optimized geometry as determined from semiempirical MNDO calculations shows that the two quinoline groups are twisted 82.5 degrees from the two phenothiazine rings, indicating a lack of electron delocalization among these groups.

Scanning electrochemical microscopy. 47. Imaging electrocatalytic activity for oxygen reduction in an acidic medium by the tip generation-substrate collection mode.

The oxygen reduction reaction (ORR) in acidic medium was studied on different electrode materials by scanning electrochemical microscopy (SECM) operating in a new variation of the tip generation-substrate collection mode. An ultramicroelectrode tip placed close to the substrate electrode oxidizes water to oxygen at a constant current. The substrate is held at a potential where the tip-generated oxygen is reduced and the resulting substrate current is measured.

Scanning electrochemical microscopy. 46. Shielding effects on reversible and quasireversible reactions.

An approximate theory for the feedback mode of the scanning electrochemical microscope (SECM) is developed to interpret the effects of substrate shielding on an ultramicroelectrode tip during a recording of iT versus d curves (approach curves) for reversible and quasireversible kinetics at a substrate surface. The resulting expressions for the tip current, iT, show a good fit to more accurate SECM simulations as well as to the experimental response of a reversible and quasireversible reaction. SECM shielding experiments thus give an interesting new insight into SECM approach curves over electrodes at different potentials, which suggest possible applications to measuring heterogeneous kinetics for fast reactions and diffusion coefficient determination.

Stability of thin-film solid-state electroluminescent devices based on tris(2,2'-bipyridine)ruthenium(II) complexes.

The factors affecting the operating life of the light-emitting electrochemical cells (LECs) based on films of tris(2,2'-bipyridine)ruthenium(II) both in sandwich (using an ITO anode and a Ga:Sn cathode) and planar (using interdigitated electrode arrays (IDAs)) configurations were investigated. Stability of these devices is greatly improved when they are produced and operated under drybox conditions. The proposed mechanism of the LEC degradation involves formation of a quencher in a small fraction of tris(2,2'-bipyridine)ruthenium(II) film adjacent to the cathode, where light generation occurs, as follows from the observed electroluminescence profile in the LECs constructed on IDAs, showing that the charge injection in such devices is highly asymmetric, favoring hole injection.

Electrogenerated chemiluminescence 69: the tris(2,2'-bipyridine)ruthenium(II), (Ru(bpy)3(2+))/tri-n-propylamine (TPrA) system revisited-a new route involving TPrA*+ cation radicals.

The reaction occurring on electrooxidation of Ru(bpy)(3)(2+) (bpy = 2,2'-bipyridine) and tri-n-propylamine (TPrA) leads to the production of Ru(bpy)(3)(2+) and light emission. The accepted mechanism of this widely used reaction involves the reaction of Ru(bpy)(3)(3+) and a reduced species derived from the free radical of the TPrA. However, this mechanism does not account for many of the observed features of this reaction.

Scanning electrochemical microscopy. 44. Imaging of horseradish peroxidase immobilized on insulating substrates.

Scanning electrochemical microscopy (SECM) was used to study horseradish peroxidase (HRP) immobilized with copolymer on insulating substrates (glass slide or polycarbonate membrane filter). Two methods were used to immobilize HRP: In the first, HRP was coimmobilized by cross-linking on a glass slide with a copolymer swelled in water to form a hydrogel; in the second, the same copolymer and avidin were coimmobilized on the glass slide and biotin-labeled HRP was conjugated to the avidin of the film. SECM was then used to detect the presence of the bound enzyme by observing the feedback current in a solution of benzoquinone and hydrogen peroxide, when hydroquinone was generated at the tip.

Combined scanning electrochemical/optical microscopy with shear force and current feedback.

A technique that combines scanning electrochemical microscopy (SECM) and scanning optical microscopy (OM) was developed. Simultaneous scanning electrochemical/optical microscopy (SECM/OM) was performed by a special probe tip, which consists of an optical fiber core for light passage, surrounded by a gold ring electrode, and an outermost electrophoretic insulating sheath, with the tip attached to a tuning fork. To regulate the tip-substrate distance, either the shear force or the SECM tip current was employed as the feedback signal.

Fabrication and characterization of probes for combined scanning electrochemical/optical microscopy experiments.

A technique that combines scanning electrochemical microscopy (SECM) and optical microscopy (OM) was implemented with a new probe tip. The tip for scanning electrochemicaVoptical microscopy (SECM/OM) was constructed by insulating a typical gold-coated near-field scanning optical microscopy tip using electrophoretic anodic paint. Once fabricated, the tip was characterized by steady-state cyclic voltammetry, as well as optical and electrochemical approach experiments.

Pressure-induced insulator conductor transition in a photoconducting organic liquid-crystal film.

Intermolecular separation determines the extent of orbital overlap and thus the rate of electron transfer between neighbouring molecules in an organic crystal. If such a crystal is compressed, the resistivity decreases owing to a diminishing intermolecular distance. Metal insulator transitions have been observed by applying hydrostatic pressure to, for example, Langmuir films of metal nanoparticles.

Thin-film solid-state electroluminescent devices based on tris(2,2'-bipyridine)ruthenium(II) complexes.

The behavior of light-emitting electrochemical cells (LEC) based on solid films ( approximately 100 nm) of tris(2,2'-bipyridine)ruthenium(II) between an ITO anode and a Ga-In cathode was investigated. The response times were strongly influenced by the nature of the counterion: small anions (BF(4)(-) and ClO(4)(-)) led to relatively fast transients, while large anions (PF(6)(-), AsF(6)(-)) produced a slow time-response. From comparative experiments of cells prepared and tested in a glovebox to those in ambient, mobility of the anions in these films appears to be related to the presence of traces of water from atmospheric moisture.

Electrochemistry and electrogenerated chemiluminescence from silicon nanocrystal quantum dots.

Reversible electrochemical injection of discrete numbers of electrons into sterically stabilized silicon nanocrystals (NCs) (approximately 2 to 4 nanometers in diameter) was observed by differential pulse voltammetry (DPV) in N,N'-dimethylformamide and acetonitrile. The electrochemical gap between the onset of electron injection and hole injection-related to the highest occupied and lowest unoccupied molecular orbitals-grew with decreasing nanocrystal size, and the DPV peak potentials above the onset for electron injection roughly correspond to expected Coulomb blockade or quantized double-layer charging energies. Electron transfer reactions between positively and negatively charged nanocrystals (or between charged nanocrystals and molecular redox-active coreactants) occurred that led to electron and hole annihilation, producing visible light.

Charge transport through self-assembled monolayers of compounds of interest in molecular electronics.

The electrical properties of self-assembled monolayers (SAMs) on metal surfaces have been explored for a series of molecules to address the relation between the behavior of a molecule and its structure. We probed interfacial electron transfer processes, particularly those involving unoccupied states, of SAMs of thiolates or arylates on Au by using shear force-based scanning probe microscopy (SPM) combined with current-voltage (i-V) and current-distance (i-d) measurements. The i-V curves of hexadecanethiol in the low bias regime were symmetric around 0 V and the current increased exponentially with V at high bias voltage.