Marginal and Internal Adaptation of Zirconia Crowns: A Comparative Study of Assessment Methods.

Marginal and internal adaptation is critical for the success of indirect restorations. New imaging systems make it possible to evaluate these parameters with precision and non-destructively. This study evaluated the marginal and internal adaptation of zirconia copings fabricated with two different systems using both silicone replica and microcomputed tomography (micro-CT) assessment methods.

Marginal and internal fit of zirconia copings obtained using different digital scanning methods.

The objective of this study was to evaluate the marginal and internal fit of zirconia copings obtained with different digital scanning methods. A human mandibular first molar was set in a typodont with its adjacent and antagonist teeth and prepared for an all-ceramic crown. Digital impressions were made using an intraoral scanner (3Shape).

Fatigue stipulation of bulk-fill composites: An in vitro appraisal.

Objectives: The aim of this study was to determine the Weibull and slow crack growth (SCG) parameters of bulk-fill resin based composites. The strength degradation over time of the materials was also assessed by strength-probability-time (SPT) analysis.

Methods: Three bulk-fill [Tetric EvoCeram Bulk Fill (TBF); X-tra fil (XTR); Filtek Bulk-fill flowable (BFL)] and a conventional one [Filtek Z250 (Z250)] were studied.

Post-cementation colorimetric evaluation of the interaction between the thickness of ceramic veneers and the shade of resin cement.

Purpose: To evaluate the color parameters (CIELab*) after the cementation of ceramic disks of different thicknesses onto a resin substrate using four different shades of resin cements, and determine the color difference (ΔE) between the adhesively cemented disks and a 10 mm-thick A1 shade ceramic control (target color).

Methods: Ceramic disks, simulating laminate veneers, with thicknesses of 0.5, 0.

Fracture toughness and cyclic fatigue resistance of resin composites with different filler size distributions.

Objectives: To verify the influence of filler size distributions on fracture toughness (KIc), initial fracture strength (IFS) and cyclic fatigue resistance (CFR) of experimental resin composites.

Methods: Four composites were prepared with same inorganic content (78 wt%), in which 67 wt% was constituted by glass particles with d50 of 0.5; 0.

Influence of the base and diluent monomer on network characteristics and mechanical properties of neat resin and composite materials.

This study evaluated the effect of the combination of two dimethacrylate-based monomers [bisphenol A diglycidyl dimethacrylate (BisGMA) or bisphenol A ethoxylated dimethacrylate (BisEMA)] with diluents either derived from ethylene glycol dimethacrylate (ethylene glycol dimethacrylate, diethylene glycol dimethacrylate, triethylene glycol dimethacrylate, tetraethylene glycol dimethacrylate) or 1,10-decanediol dimethacrylate (D3MA) on network characteristics and mechanical properties of neat resin and composite materials. The degree of conversion, maximum rate of polymerization and water sorption/solubility of unfilled resins and the flexural strength and microhardness of composites (after 24 h storage in water and 3 months storage in a 75 vol% ethanol aqueous solution) were evaluated. Data were analyzed with two-way ANOVA and Tukey's test (α = 0.

Influence of the interposition of ceramic spacers on the degree of conversion and the hardness of resin cements.

This study evaluated: I) the effect of photo-activation through ceramics on the degree of conversion (DC) and on the Knoop hardness (KHN) of light- and dual-cured resin cements; and II) two different protocols for obtaining the spectra of uncured materials, to determine the DC of a dual-cured resin cement. Thin films of cements were photo-activated through ceramics [feldspathic porcelain (FP); lithium disilicate glass-ceramics of low translucency (e.max-LT), medium opacity (e.

Subcritical crack growth and in vitro lifetime prediction of resin composites with different filler distributions.

Objectives: Verify the influence of different filler distributions on the subcritical crack growth (SCG) susceptibility, Weibull parameters (m and σ(0)) and longevity estimated by the strength-probability-time (SPT) diagram of experimental resin composites.

Methods: Four composites were prepared, each one containing 59 vol% of glass powder with different filler sizes (d(50)=0.5; 0.