Investigation of Calcium Phosphate-Based Biopolymer Composite Scaffolds for Bone Tissue Engineering.

We present a novel method for preparing bioactive and biomineralized calcium phosphate (mCP)-loaded biopolymer composite scaffolds with a porous structure. Two types of polymers were investigated as matrices: one natural, cellulose acetate (CA), and one synthetic, polycaprolactone (PCL). Biomineralized calcium phosphate particles were synthesized via wet chemical precipitation, followed by the addition of organic biominerals, such as magnesium gluconate and zinc gluconate, to enhance the bioactivity of the pure CP phase.

Advances, Challenges, and Applications of Graphene and Carbon Nanotube-Reinforced Engineering Ceramics.

Engineering ceramics and their composites are widely used owing to their excellent properties, including high wear, corrosion and heat resistance, low friction coefficient, and low thermal conductivity; thus, the current paper presents a comprehensive review of the most common types of engineering ceramics, demonstrating their key properties, advantages, potential applications, and challenges. This paper also provides prevailing methods for tackling the engineering ceramic challenges and maximizing their applicability. This review paper focuses on alumina (AlO), silicon carbide (SiC), zirconia (ZrO), aluminum nitride (AlN), and silicon nitride (SiN), and explores their usability in automotive, aerospace, and tribological applications.

Hydroxyapatite-Based Natural Biopolymer Composite for Tissue Regeneration.

Hydroxyapatite (HAp) polymer composites have gained significant attention due to their applications in bone regeneration and tooth implants. This review examines the synthesis, properties, and applications of Hap, highlighting various manufacturing methods, including wet, dry, hydrothermal, and sol-gel processes. The properties of HAp are influenced by precursor materials and are commonly obtained from natural calcium-rich sources like eggshells, seashells, and fish scales.

Diffusion Bonding of AlO Dispersion-Strengthened 316L Composite by Gleeble 3800.

The aim of this work is to investigate the bonding properties of the ceramic dispersion-strengthened 316L (CDS-316L) composites with the reference 316L stainless steel (REF-316L) using a Gleeble 3800 physical simulator. In previous works, two different composites, REF-316L and 316L, with 1 wt% AlO composite (CDS-316L) have been prepared by spark plasma sintering (SPS). In the present work, these specimens were diffusion-bonded using the following parameters: a temperature range of 950-1000 °C and a uniaxial pressure of 20-30 MPa.

Amorphous, Carbonated Calcium Phosphate and Biopolymer-Composite-Coated SiN/MWCNTs as Potential Novel Implant Materials.

A biodegradable amorphous carbonated calcium phosphate (caCP)-incorporated polycaprolactone (PCL) composite layer was successfully deposited by a spin coater. In this specific coating, the PCL acts as a bioadhesive, since it provides a better adherence of the coatings to the substrate compared to powder coatings. The caCP-PCL coatings were deposited and formed thin layers on the surface of a SiN-3 wt% MWCNT (multiwalled carbon nanotube) substrate, which is an emerging type of implant material in the biomedical field.

Advanced Bioactive Glasses: The Newest Achievements and Breakthroughs in the Area.

Bioactive glasses (BGs) are especially useful materials in soft and bone tissue engineering and even in dentistry. They can be the solution to many medical problems, and they have a huge role in the healing processes of bone fractures. Interestingly, they can also promote skin regeneration and wound healing.

Biominerals Added Bioresorbable Calcium Phosphate Loaded Biopolymer Composites.

Nanocrystalline calcium phosphate (CP) bioceramic coatings and their combination with biopolymers are innovative types of resorbable coatings for load-bearing implants that can promote the integration of metallic implants into human bodies. The nanocrystalline, amorphous CP particles are an advantageous form of the various calcium phosphate phases since they have a faster dissolution rate than that of crystalline hydroxyapatite. Owing to the biomineral additions (Mg, Zn, Sr) in optimized concentrations, the base CP particles became more similar to the mineral phase in human bones (dCP).

Influence of Graphene Type and Content on Friction and Wear of Silicon Carbide/Graphene Nanocomposites in Aqueous Environment.

Two different types of graphene materials were used as functional nanofillers for the mechanical and tribological improvement of silicon carbide/graphene nanocomposites. On the one hand is thermally reduced graphite oxide (TRGO) reduced at three different temperatures, and on the other hand is graphene made of three different organic precursors, which were directly coated on silicon carbide (SiC) platelets (GSiC). Additionally, benchmark materials were also used as carbon fillers.

Investigation of the RF Sputtering Process and the Properties of Deposited Silicon Oxynitride Layers under Varying Reactive Gas Conditions.

In a single process run, an amorphous silicon oxynitride layer was grown, which includes the entire transition from oxide to nitride. The variation of the optical properties and the thickness of the layer was characterized by Spectroscopic Ellipsometry (SE) measurements, while the elemental composition was investigated by Energy Dispersive Spectroscopy (EDS). It was revealed that the refractive index of the layer at 632.

Effect of the pressureless post-sintering on the hot isostatic pressed AlO prepared from the oxidized AlN powder.

The effect of the pressureless post-sintering in hydrogen on the structural and mechanical properties of the hot isostatic pressed AlO prepared by oxidized AlN powder has been studied. The micrometer size AlN powder has been oxidized in air at 900° C and sintered by hot isostatic pressing (HIP) at 1700 °C, 20 MPa nitrogen atmosphere for 5 h. Pressureless sintering (PS) has been applied for all HIP sintered samples in H gas at 1800° C for 10 h.

Comparison of the Morphological and Structural Characteristic of Bioresorbable and Biocompatible Hydroxyapatite-Loaded Biopolymer Composites.

Calcium phosphate (CaP)-based ceramic-biopolymer composites can be regarded as innovative bioresorbable coatings for load-bearing implants that can promote the osseointegration process. The carbonated hydroxyapatite (cHAp) phase is the most suitable CaP form, since it has the highest similarity to the mineral phase in human bones. In this paper, we investigated the effect of wet chemical preparation parameters on the formation of different CaP phases and compared their morphological and structural characteristics.

Processing of AlO-AlN Ceramics and Their Structural, Mechanical, and Tribological Characterization.

The aim of this study is to present a novel, lower sintering temperature preparation, processing, structural, mechanical, and tribological testing of the AlN-AlO ceramics. The precursor powder of AlN was subjected to oxidation in ambient environment at 900 °C for 3, 10, and 20 h, respectively. These oxidized powders were characterized by SEM and XRD to reveal their morphology, phase, and crystal structure.

Microstructure and Fracture Mechanism Investigation of Porous Silicon Nitride-Zirconia-Graphene Composite Using Multi-Scale and In-Situ Microscopy.

Silicon nitride-zirconia-graphene composites with high graphene content (5 wt.% and 30 wt.%) were sintered by gas pressure sintering (GPS).

Highly wear-resistant and low-friction SiN composites by addition of graphene nanoplatelets approaching the 2D limit.

Graphene nanoplatelets (GNPs) have emerged as one of the most promising filler materials for improving the tribological performance of ceramic composites due to their outstanding solid lubricant properties as well as mechanical and thermal stability. Yet, the addition of GNPs has so far enabled only a very limited improvement in the tribological properties of ceramics, particularly concerning the reduction of their friction coefficient. This is most likely due to the challenges of achieving a continuous lubricating and protecting tribo-film through a high GNP coverage of the exposed surfaces.

Structural and biocompatible characterization of TiC/a:C nanocomposite thin films.

In this work, sputtered TiC/amorphous C thin films have been developed in order to be applied as potential barrier coating for interfering of Ti ions from pure Ti or Ti alloy implants. Our experiments were based on magnetron sputtering method, because the vacuum deposition provides great flexibility for manipulating material chemistry and structure, leading to films and coatings with special properties. The films have been deposited on silicon (001) substrates with 300 nm thick oxidized silicon sublayer at 200 °C deposition temperature as model substrate.

Caspase 3 activity is required for skeletal muscle differentiation.

The cellular alterations associated with skeletal muscle differentiation share a high degree of similarity with key phenotypic changes usually ascribed to apoptosis. For example, actin fiber disassembly/reorganization is a conserved feature of both apoptosis and differentiating myoblasts and the conserved muscle contractile protein, myosin light chain kinase, is required for the apoptotic feature of membrane blebbing. As such, these observations suggest that the induction of differentiation and apoptosis in the myogenic lineage may use overlapping cellular mechanisms.

Activation of JNK1 contributes to dystrophic muscle pathogenesis.

Duchenne Muscular Dystrophy (DMD) originates from deleterious mutations in the dystrophin gene, with a complete loss of the protein product. Subsequently, the disease is manifested in severe striated muscle wasting and death in early adulthood. Dystrophin provides a structural base for the assembly of an integral membrane protein complex.

Ca2+ and BMP-6 signaling regulate E2F during epidermal keratinocyte differentiation.

The epidermis consists of a squamous epithelium continuously replenished by committed stem cells, which can either self-renew or differentiate. We demonstrated previously that E2F genes are differentially expressed in developing epidermis (Dagnino, L., Fry, C.

MEF2 is upregulated during cardiac hypertrophy and is required for normal post-natal growth of the myocardium.

In mammals, growth of the fetal heart is regulated by proliferation of cardiac muscle cells. At later stages of pre-natal life, this proliferation diminishes profoundly [1] [2] and the dramatic expansion in heart size during the transition to adulthood is due exclusively to hypertrophy of individual cardiomyocytes [3] [4] [5]. Cardiomyocyte hypertrophy also contributes to the pathology of most post-natal heart disease [6] [7] [8] [9] [10].

Comparison of a reverse transcription-polymerase chain reaction assay and virus isolation for the detection of classical swine fever virus.

The authors evaluated the ability of a reverse transcription-polymerase chain reaction (RT-PCR) assay to detect classical swine fever virus (CSFV) in comparison with virus isolation and detection by an indirect immunoperoxidase assay (VI-IPA). To determine the specificity of the assay, samples from 60 spleens, 45 tonsils, ten submandibular lymph nodes, eight mesenteric lymph nodes and four kidneys, collected from pigs of various ages which had been slaughtered in abattoirs in Canada (a population free from CSFV), were tested. All the samples tested gave negative results by both VI-IPA and RT-PCR.