Concept and simulation of an alternative design for an orthopaedic shoulder implant.

For a first-time glenohumeral arthritis patient, total shoulder arthroplasty (TSA) is an option where the shoulder joint is replaced with an artificial humeral head that articulates against a cup attached to the glenoid. A patient with rotator cuff deficiency can undergo reverse total shoulder arthroplasty (RTSA) where the components are switched. Presented here is a concept design at simulation stage which offers a platform-based implant where either a system can be assembled and implanted for TSA or a reverse system for RTSA.

Design of a novel midstream fluid waste sample collection device for patients.

Reducing the contamination rates in mid-stream urine samples is a challenge. A novel design for a mid-stream urine sample collection device, which uses a novel mechanism to separate the mid-stream flow from the fore-stream and end-stream flows based on flow speed, is presented. The device, supplied in two parts, is designed to be clipped to a toilet and used in a seated position, which improves ease of use for disabled patients.

Effect of accelerated aging on the cross-link density of medical grade silicones.

Four specimens of Nagor silicone of different hardness (soft, medium and hard) were swollen, until they reached equilibrium (i.e. constant mass) in five liquids at 25°C, before and after accelerated aging.

Effect of accelerated aging on the viscoelastic properties of a medical grade silicone.

The viscoelastic properties of cylinders (diameter 5 mm, height 2.2 ± 0.2 mm) of Nagor silicone elastomer of medium hardness, were investigated before and after the specimens had undergone accelerated aging in saline solution at 70°C for 38, 76 and 114 days (to simulate aging at 37°C, for 1, 2 and 3 years, respectively).

Wear of the Charité® lumbar intervertebral disc replacement investigated using an electro-mechanical spine simulator.

The Charité(®) lumbar intervertebral disc replacement was subjected to wear testing in an electro-mechanical spine simulator. Sinusoidally varying compression (0.6-2 kN, frequency 2 Hz), rotation (±2°, frequency 1 Hz), flexion-extension (6° to -3°, frequency 1 Hz) and lateral bending (±2°, frequency 1 Hz) were applied out of phase to specimens immersed in diluted calf serum at 37 °C.

Determining the solubility parameter and the cross-link density of medical grade silicones: effect of increasing the range of swelling liquids.

Four samples of four medical grade silicones were swollen in six "good" liquids (i.e. those with a good swelling ability, in which silicones swell appreciably) at 25°C, until they reached constant mass (i.

Effect of lubricants on friction in laboratory tests of a total disc replacement device.

Some designs of total disc replacement devices have articulating bearing surfaces, and these devices are tested in vitro with a lubricant of diluted calf serum. It is believed that the lubricant found in total disc replacement devices in vivo is interstitial fluid that may have properties between that in Ringer's solution and diluted calf serum. To investigate the effect of lubricants, a set of friction tests were performed on a generic model of a metal against metal ball-and-socket total disc replacement device.

Wear in metal-on-metal total disc arthroplasty.

The wear of a model metal-on-metal ball-and-socket total disc arthroplasty was measured in a simulator. The ball had a radius of 10 mm, and there was a radial clearance between ball and socket of 0.015 mm.

Polymer-on-metal or metal-on-polymer total disc arthroplasty: does it make a difference?

Study Design: Mechanical testing of total disc arthroplasty (TDA).

Objective: To compare the friction between a polymer socket-on-metal ball and metal socket-on-polymer ball TDA.

Summary Of Background Data: A degenerate intervertebral disc can be replaced by TDA.

Effect of axial load on the flexural properties of an elastomeric total disc replacement.

Study Design: Twelve Cadisc-L devices were subjected to flexion (0°-6°) and extension (0° to -3°) motions at compressive loads between 500 N and 2000 N at a flexural rate between 0.25°/s and 3.0°/s.

Friction in metal-on-metal total disc arthroplasty: effect of ball radius.

Total disc arthroplasty (TDA) can be used to replace a degenerated intervertebral disc in the spine. There are different designs of prosthetic discs, but one of the most common is a ball-and-socket combination. Contact between the bearing surfaces can result in high frictional torque, which can then result in wear and implant loosening.

Swelling of medical grade silicones in liquids and calculation of their cross-link densities.

Four medical grade silicones were swollen, until they reached equilibrium (i.e. constant mass) in eight liquids at 25 degrees C.