Evaluating the effects of splinting implant scan bodies intraorally on the trueness of complete arch digital scans: A clinical study.

Statement Of Problem: A predictable protocol for accurately scanning implants in a complete edentulous arch has not been established.

Purpose: The purpose of this clinical study was to investigate the effect of splinting implant scan bodies intraorally on the accuracy and scan time for digital scans of edentulous arches.

Material And Methods: This single center, nonrandomized, clinical trial included a total of 19 arches.

Scanning accuracy with splinted and unsplinted implant scan bodies for the edentulous arch at implant level: an in vitro study.

Accuracy of completely edentulous arch scanning with implant scan bodies has not been completely validated for intraoral scanners. For desktop laboratory scanners validations were found in the literature. The aim of this in vitro study was to compare the dimensional accuracy of scanning with splinted and unsplinted scan bodies on a completely edentulous maxillary arch with 6 implants.

Use of Implant-Supported Custom Milled Impression Copings to Capture Soft-Tissue Contours and Incisal Guidance.

A technique is presented where a custom milled impression coping is used to replicate the clinically established anterior incisal guidance to the definitive prosthesis when multiple implants are restored in the esthetic zone. A conventional impression is initially made, then the stone cast is scanned, and a digitally designed custom screw-retained, implant-supported interim prosthesis is milled from a polymethylmethacrylate (PMMA) billet. This is aimed to digitally design the pontic areas, contour the gingival soft tissue, and establish an anterior incisal guidance.

Use of Patient's Own Natural Teeth as Part of the Interim Prosthesis on Immediately Placed Single Implants in a Staged Surgical Approach: A Clinical Report.

A technique is described where the tooth's natural crown is used as part of the interim implant supported prosthesis in clinical situations where a tooth with poor prognosis is extracted and an implant is placed immediately after tooth extraction. A preliminary impression is made before tooth extraction, and the exact tooth positioning is assessed in the laboratory as part of the treatment plan. An acrylic resin repositioning jig is fabricated that will guide the clinician in seating and orienting the crown intraorally after implant placement is completed.

Digital technology for performing a nasopalatine and greater palatine nerve block with a modified implant surgical guide: A technique article.

This article describes a computer-aided design and computer-aided manufacturing (CAD-CAM) technique to perform a precise nerve block of the nasopalatine and greater palatine nerves by using an implant surgical guide. The technique uses additional guide anchor pins planned and positioned for specific anatomic landmarks during guided implant surgical guide planning. A relief modification virtually designed on the intaglio surface of the surgical guide allows for palatal soft tissue distension following administration of local anesthetic.

CAD-CAM implant-supported fixed complete dental prosthesis with titanium milled molars: A clinical report.

Implant-supported fixed complete dental prostheses have been associated with a high implant success rate in long-term studies. However, they have also been associated with a high frequency of prosthetic complications. The most frequent and primary prosthetic complication has been the fracture or wear of the occlusal surface of acrylic resin teeth that are typically attached to a metal framework.

Digitally planned and fabricated mandibular fixed complete dentures. Part 2. Prosthodontic phase.

Part 1 of this patient report described a prosthetically driven protocol that used computer-aided engineering for the fabrication of a mandibular conversion denture and maxillary provisional complete denture using the AvaDent Digital Denture system. The report demonstrated that this system combined with NobelClinician implant-planning software can be used to efficiently convert a digital denture into an immediately loaded provisional implant-supported fixed complete denture (hybrid prosthesis). Part 2 of the patient report describes the technique and steps involved in the fabrication of a digitally planned and fabricated mandibular fixed complete denture with incorporated titanium milled bar opposed by a definitive computer-aided design/computer-assisted manufacture-milled maxillary complete denture.

Degree of patient pain, complications, and satisfaction after root canal treatment or a single implant: a preliminary prospective investigation.

Introduction: Dentists often face the choice between tooth retention with root canal treatment and tooth replacement with implant treatment. To date, there has not been a prospective clinical trial directly comparing nonsurgical root canal treatment and single delayed implant therapy with regard to the degree of preoperative and postoperative pain, complications, and patient satisfaction.

Methods: Twenty-four patients had initial nonsurgical root canal treatment, and another 24 had single implant treatment in healed sites.

Use of a digitally planned and fabricated mandibular complete denture for easy conversion to an immediately loaded provisional fixed complete denture. Part 1. Planning and surgical phase.

This article describes a unique prosthetically driven protocol that uses computeraided engineering to develop sophisticated, scientific algorithms that guide the fabrication of a conversion denture using the AvaDent Digital Denture system (Global Dental Science). This system is combined with Nobel Clinician (Nobel Biocare) implant-planning software to optimize accuracy and to make it easier and faster to convert a denture to an immediately loaded provisional implant supported fixed complete denture following implant placement, using a NobelGuide surgical template.

The incidence of maxillary sinus membrane perforation during endoscopically assessed crestal sinus floor elevation: a pilot study.

Transcrestal sinus membrane elevation is a surgical procedure performed to increase the bone volume in the maxillary sinus cavity. Because of visual limitations, the potential for maxillary sinus membrane perforations may be greater than with the lateral approach technique. The aim of this study was to macroscopically investigate ex vivo the occurrence of sinus membrane perforation during surgery using 3 transcrestal sinus floor elevation methods.

CAD/CAM fabricated complete dentures: concepts and clinical methods of obtaining required morphological data.

The clinical impression procedures described in this article provide a method of recording the morphology of the intaglio and cameo surfaces of complete denture bases and also identify muscular and phonetic locations for the prosthetic teeth. When the CAD/CAM technology for fabricating complete dentures becomes commercially available, it will be possible to scan the denture base morphology and tooth positions recorded with this technique and import those data into a virtual tooth arrangement program where teeth can be articulated and then export the data to a milling device for the fabrication of the complete dentures. A prototype 3-D tooth arrangement program is described in this article that serves as an example of the type of program than can be used to arrange prosthetic teeth virtually as part of the overall CAD/CAM fabrication of complete dentures.

Lateral and crestal bone planing antrostomy: a simplified surgical procedure to reduce the incidence of membrane perforation during maxillary sinus augmentation procedures.

This clinical report presents a simplified surgical procedure for accessing the maxillary sinus antrum via lateral and crestal approaches, which reduces the potential for sinus membrane perforation and subsequent complications when graft materials and dental implants are placed into the sinus. Due to visual limitations, perforations and associated complications can jeopardize the success rate of the graft and the implants. While there is a lack of clinical data, clinical observations suggest that the procedure, described by the authors as lateral/crestal bone planing antrostomy, can reduce the possibility of perforation of the maxillary sinus membrane during the lateral and crestal approaches to the grafting of the maxillary sinus floor.