Printed and Flexible Microheaters Based on Carbon Nanotubes.

This work demonstrates a cost-effective manufacturing method of flexible and fully printed microheaters, using carbon nanotubes (CNTs) as the heating element. Two different structures with different number of CNT layers have been characterized in detail. The benchmarking has been carried out in terms of maximum operating temperature, as well as nominal resistance and input power for different applied voltages.

Low-Cost Gas Sensing: Dynamic Self-Compensation of Humidity in CNT-Based Devices.

Solid-state gas sensors are a cost-effective and well-spread alternative to conventional gas sensing, employable in most environments, ranging from homes and offices to harsh industrial scenarios. The emergence of carbon nanotubes (CNTs) as sensing material in solid-state gas sensors paved the way to a new class of devices, which are semitransparent, flexible, and with a remarkably low environmental impact. These devices, however, lack selectivity to other gases and concurring physical phenomena, such as temperature and pressure changes.

Fully Transparent Gas Sensor Based on Carbon Nanotubes.

In this paper, we demonstrate the feasibility of realization of transparent gas sensors based on carbon nanotubes (CNTs). Both sensing layer and electrodes consist of CNTs deposited by spray deposition. The transparent sensor-with a transmittance higher than 60% in both sensing layer and electrodes-is characterized towards NH and CO and compared with a reference sensor with the same active layer but evaporated Au electrodes.

Development of Flexible Dispense-Printed Electrochemical Immunosensor for Aflatoxin M1 Detection in Milk.

Detection of mycotoxins, especially aflatoxin M1 (AFM1), in milk is crucial to be able to guarantee food quality and safety. In recent years, biosensors have been emerging as a fast, reliable and low-cost technique for the detection of this toxin. In this work, flexible biosensors were fabricated using dispense-printed electrodes, which were functionalized with single-walled carbon nanotubes (SWCNTs) and subsequently coated with specific antibodies to improve their sensitivity.

Cost-effective PEDOT:PSS Temperature Sensors Inkjetted on a Bendable Substrate by a Consumer Printer.

In this work, we report on a fabrication protocol to produce fully inkjet-printed temperature sensors on a bendable polyethylene terephthalate (PET) substrate. The sensing layer is made of polymer-based Poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) ink that is electrically contacted by an underlying interdigitated electrode (IDE) structure based on a silver nanoparticle (AgNP) ink. Both inks are available commercially, and no further ink processing is needed to print them using a cost-effective consumer printer with standard cartridges.

A Handwriting Method for Low-Cost Gas Sensors.

In this study, we report on an automated method based on a handwritten technique for the fabrication of low-cost gas sensors based on carbon nanotube (CNT) networks. Taking advantage of the inherent low-cost, flexible, and uncomplicated characteristics of pen-based techniques and combining them with an automated robotic system allows for high-resolution patterns, high reproducibility, and relatively high throughput considering the limitations of parallel processing. To showcase this, gas sensors capable of sensing NH, CO, CO, and ethanol, as well as temperature and relative humidity, are fabricated and characterized displaying competitive performance in relation to previously reported devices.

Use of SU8 as a stable and biocompatible adhesion layer for gold bioelectrodes.

Gold is the most widely used electrode material for bioelectronic applications due to its high electrical conductivity, good chemical stability and proven biocompatibility. However, it adheres only weakly to widely used substrate materials such as glass and silicon oxide, typically requiring the use of a thin layer of chromium between the substrate and the metal to achieve adequate adhesion. Unfortunately, this approach can reduce biocompatibility relative to pure gold films due to the risk of the underlying layer of chromium becoming exposed.

Fully Printed Flexible Single-Chip RFID Tag with Light Detection Capabilities.

A printed passive radiofrequency identification (RFID) tag in the ultra-high frequency band for light and temperature monitoring is presented. The whole tag has been manufactured by printing techniques on a flexible substrate. Antenna and interconnects are realized with silver nanoparticles via inkjet printing.

Transfer Printed P3HT/PCBM Photoactive Layers: From Material Intermixing to Device Characteristics.

The fabrication of organic electronic devices involving complex stacks of solution-processable functional materials has proven challenging. Significant material intermixing often occurs as a result of cross-solubility and postdeposition treatments, rendering the realization of even the simplest bilayer architectures rather cumbersome. In this study we investigate the feasibility of a dry transfer printing process for producing abrupt bilayer organic photodiodes (OPDs) and the effect of thermal annealing on the integrity of the bilayer.

Fully-sprayed and flexible organic photodiodes with transparent carbon nanotube electrodes.

In this study, we demonstrate the feasibility of TCO-free, fully sprayed organic photodiodes on flexible polyethylene terephthalate (PET) substrates. Transparent conducting films of single-wall carbon nanotubes are spray deposited from aqueous solutions. Low roughness is achieved, and films with sheet resistance values of 160 Ω/sq at 84% in transmittance are fabricated.