Hybrid Nanocomposites Based on Poly(3,6-dianiline-2,5-dichloro-1,4-benzoquinone): Synthesis, Structure and Properties.

Hybrid nanocomposites based on poly(3,6-dianiline-2,5-dichloro-1,4-benzoquinone) (PDACB) in salt form and graphene oxide (GO) have been obtained for the first time, and the significant influence of the preparation method on the composition and structure of nanocomposites and their functional properties has been demonstrated. Nanocomposites were prepared in three ways: via ultrasonic mixing of PDACB and GO; via in situ oxidative polymerization of 3,6-dianiline-2,5-dichloro-1,4-benzoquinone (DACB) in the presence of GO; and by heating a suspension of previously prepared PDACB and GO in DMF with the removal of the solvent. The results of the study of the composition, chemical structure, morphology, thermal stability and electrical properties of nanocomposites obtained via various methods are presented.

Application of Infrared Pyrolysis and Chemical Post-Activation in the Conversion of Polyethylene Terephthalate Waste into Porous Carbons for Water Purification.

In this study, we compared the conversion of polyethylene terephthalate (PET) into porous carbons for water purification using pyrolysis and post-activation with KOH. Pyrolysis was conducted at 400-850 °C, followed by KOH activation at 850 °C for samples pyrolyzed at 400, 650, and 850 °C. Both pyrolyzed and post-activated carbons showed high specific surface areas, up to 504.

Fe-Co Alloy Nanoparticles Dispersed in Polymer-Derived Carbon Support: Effect of Initial Polymer Nature on the Size, Structure and Magnetic Properties.

Fe-Co alloy nanoparticles with different sizes, supported by carbon derived from several polymers, namely polyacrylonitrile, polyvinyl alcohol and chitosan, have been synthesized by a one-pot method involving simultaneous metal nanoparticle formation and polymer carbonization. The method involves the joint dissolution of metal salts and a polymer, followed by annealing of the resulting dried film. Detailed XRD analysis confirmed the formation of Fe-Co alloy nanoparticles in each sample, regardless of the initial polymer used.

Formation Features of Polymer-Metal-Carbon Ternary Electromagnetic Nanocomposites Based on Polyphenoxazine.

Novel ternary hybrid polyphenoxazine (PPOA)-derived nanocomposites involving Co-Fe particles and single-walled (SWCNTs) or multi-walled (MWCNTs) carbon nanotubes were prepared and investigated. An efficient one-pot method employing infrared (IR) heating enabled the formation of Co-Fe/CNT/PPOA nanocomposites. During this, the dehydrogenation of phenoxazine (POA) units led to the simultaneous reduction of metals by released hydrogen, yielding bimetallic Co-Fe particles with a size range from the nanoscale (5-30 nm) to the microscale (400-1400 nm).

Decay Kinetics of GdAlGaO:Ce Luminescence under Dense Laser Irradiation.

The decay kinetics of GdAlGaO:Ce single crystal luminescence were studied under dense laser excitation. It was shown that the decay times as well as the intensity of Ce luminescence depend on the excitation density. The observed effects were ascribed to the interaction between excitons as well as to the features of energy transfer from the excitons to Ce.

Novel Hybrid Composites Based on Polymers of Diphenyl-Amine-2-Carboxylic Acid and Highly Porous Activated IR-Pyrolyzed Polyacrylonitrile.

Hybrid composites based on electroactive polymers of diphenylamine-2-carboxylic acid (PDPAC) and highly porous carbon with a hierarchical pore structure were prepared for the first time. Activated IR-pyrolyzed polyacrylonitrile (IR-PAN-a), characterized by a highly developed surface, was chosen as a highly porous N-doped carbon component of the hybrid materials. IR-PAN-a was prepared using pyrolysis of polyacrylonitrile (PAN) in the presence of potassium hydroxide under IR radiation.

Mechanical and Tribological Properties of Polytetrafluoroethylene Modified with Combined Fillers: Carbon Fibers, Zirconium Dioxide, Silicon Dioxide and Boron Nitride.

The introduction of combined fillers can effectively improve the mechanical and tribological properties of polytetrafluoroethylene (PTFE). In this work, three different types of nanosized fillers (zirconium dioxide, silicon dioxide, and boron nitride) were introduced in a carbon fiber-reinforced polymer matrix for the development of polymer composite materials (PCM). Tensile and compressive testing were carried out, and the hardness of created PCM was evaluated.

Effects of spatial quantization and Rabi-shifted resonances in single and double excitation of quantum wells and wires induced by few-photon optical field.

We develop a fully quantum theoretical approach which describes the dynamics of Frenkel excitons and bi-excitons induced by few photon quantum light in a quantum well or wire (atomic chain) of finite lateral size. The excitation process is found to consist in the Rabi-like oscillations between the collective symmetric states characterized by discrete energy levels. At the same time, the enhanced excitation of high-lying free exciton states being in resonance with these 'dressed' polariton eigenstates is revealed.

Bright UV-C Phosphors with Excellent Thermal Stability-YScPO Solid Solutions.

The structural and luminescence properties of undoped YScPO solid solutions have been studied. An intense thermally stable emission with fast decay (τ ~ 10 s) and a band position varying from 5.21 to 5.

Two-Layer Rubber-Based Composite Material and UHMWPE with High Wear Resistance.

The aim of the study is the development of two-layer materials based on ultra-high-molecular-weight polyethylene (UHMWPE) and isoprene rubber (IR) depending on the vulcanization accelerators (2-mercaptobenzothiazole (MBT), diphenylguanidine (DPG), and tetramethylthiuram disulfide (TMTD)). The article presents the study of the influence of these accelerators on the properties and structure of UHMWPE. It is shown that the use of accelerators to modify UHMWPE leads to an increase in tensile strength of 28-53%, a relative elongation at fracture of 7-23%, and wear resistance of three times compared to the original UHMWPE.

Design rules for time of flight Positron Emission Tomography (ToF-PET) heterostructure radiation detectors.

Despite the clinical acceptance of ToF-PET, there is still a gap between the technology's performance and the end-user's needs. Core to bridging this gap is the ability to develop radiation detectors combining a short attenuation length and a sub-nanosecond time response. Currently, the detector of choice, LuSiO:Ce single crystal, is not selected for its ability to answer the performance needs, but as a trade-off between requirements and availability.

One-step synthesis, characterization and properties of novel hybrid electromagnetic nanomaterials based on polydiphenylamine and Co-Fe particles in the absence and presence of single-walled carbon nanotubes.

A one-step preparation method for hybrid electromagnetic nanomaterials based on polydiphenylamine (PDPA) and bimetallic Co-Fe particles in the absence and presence of single-walled carbon nanotubes (SWCNT) was proposed. During IR heating of PDPA in the presence of Co(ii) and Fe(iii) salts in an inert atmosphere at = 450-600 °C, the polycondensation of diphenylamine (DPA) oligomers and dehydrogenation of phenyleneamine units of the polymer with the formation of C[double bond, length as m-dash]N bonds and reduction of metals by evolved hydrogen with the formation of bimetallic Co-Fe particles dispersed in a polymer matrix occur simultaneously. When carbon nanotubes are introduced into the reaction system, a nanocomposite material is formed, in which bimetallic Co-Fe particles immobilized on SWCNT are distributed in the matrix of the polymer.

Effect of Borpolymer on Mechanical and Structural Parameters of Ultra-High Molecular Weight Polyethylene.

The paper presents the results of studying the effect of borpolymer (BP) on the mechanical properties, structure, and thermodynamic parameters of ultra-high molecular weight polyethylene (UHMWPE). Changes in the mechanical characteristics of polymer composites material (PCM) are confirmed and complemented by structural studies. X-ray crystallography (XRC), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and infrared spectroscopy (IR) were used to study the melting point, morphology and composition of the filler, which corresponds to the composition and data of the certificate of the synthesized BP.

Perspectives for CdSe/CdS spherical quantum wells as rapid-response nano-scintillators.

We explore the effect of the shell thickness on the time response of CdS/CdSe/CdS spherical quantum wells (SQWs) nanoscintillators under X-ray excitation. We first compare the spectral and timing properties under low and intense optical excitation, which allows us to identify the complex temporal and spectral response of the highly excited species. We find that a defect-induced delayed luminescence appears at large sizes.

Hybrid Electromagnetic Nanomaterials Based on Polydiphenylamine-2-carboxylic Acid.

Hybrid ternary nanomaterials based on conjugated polymer polydiphenylamine-2-carboxylic acid (PDPAC) (poly--phenylanthranilic acid), FeO nanoparticles and single-walled carbon nanotubes (SWCNT) were prepared for the first time. Polymer-metal-carbon FeO/SWCNT/PDPAC nanocomposites were synthesized via in situ oxidative polymerization of diphenylamine-2-carboxylic acid (DPAC) by two different ways: in an acidic medium and in the interfacial process in an alkaline medium. In an alkaline medium (pH 11.

Mechanical and Tribological Properties of Polytetrafluoroethylene Composites with Carbon Fiber and Layered Silicate Fillers.

Mixtures of layered silicates (vermiculite and kaolinite) and carbon fibers were investigated as filler materials for polytetrafluoroethylene. The supramolecular structure and the tribological and mechanical properties of the resulting polymer composite materials were evaluated. The yield strength and compressive strength of the polymer increased by 55% and 60%, respectively, when a mixed filler was used, which was attributed to supramolecular reinforcement of the composites.