Physical-Mechanical Properties of Bulk Fill Composites Submitted to Biodegradation by Streptococcus mutans.

The aim of this study was to evaluate the Streptococcus mutans biofilm influence on the roughness (Ra), gloss (GU), surface hardness (KHN) and flexural strength (FS) of high viscosity bulk fill composites. Filtek Bulk Fill (FBF), Tetric N Ceram Bulk Fill (TNC), X-tra fil Bulk Fill (XF) and Filtek Z350 (FZ) were used. Ten discs of each composite were prepared for Ra, KHN and GU and 20 bars for the FS.

Influence of the incorporation of triclosan methacrylate on the physical properties and antibacterial activity of resin composite.

The incorporation of antimicrobials in the composites as an attempt to reduce bacterial adhesion without jeopardizing mechanical properties is a challenge for Dentistry. OBJECTIVE To evaluate the bacterial adhesion and physical properties of a composite containing the methacrylate triclosan- derivative monomer (TM). METHODOLOGY TM was synthesized and added to an experimental composite.

Color Stability and Gloss of Esthetic Restorative Materials after Chemical Challenges.

This study evaluated gloss and color changes of esthetic restorative materials subjected to different acidic beverages. Specimens of resin composites (Z350XT (Z350), IPS Empress Direct (ED), Charisma Diamond (CD)) were prepared and the initial surface gloss and color (ΔE) were measured (n=10). Then, the specimens were immersed in 4 mL of each of the different beverages (cranberry juice; Coca-Cola; coffee or artificial saliva) during 15 min, 3x/day for 14 days and new gloss and color readings were obtained.

Synthesis and application of triclosan methacrylate monomer in resin composites.

Objectives: To evaluate the antibacterial activity, bacterial viability, cytotoxicity, and mechanical/physical properties of a novel methacrylate triclosan-derivative monomer (TM) incorporated in dental resin composite.

Methods: TM was synthesized by esterification and, after characterization by FT-IR, was added to an experimental composite. Samples were divided into two groups according to TM presence, i.

Doxycycline-containing glass ionomer cement for arresting residual caries: an in vitro study and a pilot trial.

In a previous study, we demonstrated that the incorporation of doxycycline hyclate (DOX) into resin-modified glass ionomer cement (RMGIC) inhibited important cariogenic microorganisms, without modifying its biological and mechanical characteristics. In this study, we keep focused on the effect of that experimental material as a potential therapy for arresting residual caries by analyzing other in vitro properties and conducting a pilot clinical trial assessing the in vivo effect of DOX-containing RMGIC on residual mutans streptococci after partial carious removal in primary molars. Specimens of the groups RMGIC (control); RMGIC + 1.

A novel Triclosan Methacrylate-based composite reduces the virulence of Streptococcus mutans biofilm.

The use of antimicrobial monomers, linked to the polymer chain of resin composites, is an interesting approach to circumvent the effects of bacteria on the dental and material surfaces. In addition, it can likely reduce the incidence of recurrent caries lesions. The aim of this study was to evaluate the effects of a novel Triclosan Methacrylate (TM) monomer, which was developed and incorporated into an experimental resin composite, on Streptococcus mutans (S.

Effect of Metal Primers on Bond Strength of a Composite Resin to Nickel-Chrome Metal Alloy.

This study evaluated the effects of three metal primers and one multi-mode adhesive system on the shear bond strength (SBS) of a flowable composite resin to nickel-chrome metal alloy (Ni-Cr). Ninety plates were cast from Ni-Cr and divided in nine groups (n=10). The surfaces were sandblasted with Al2O3 and primed with three adhesive primers: Alloy Primer (AP), Universal Primer (TP) and RelyX Ceramic Primer (CP), and a multi-mode adhesive (Scotchbond Universal, SU).

Evaluation of sorption/solubility, softening, flexural strength and elastic modulus of experimental resin blends with chlorhexidine.

Objectives: To evaluate physical-chemical properties of experimental diacetate chlorhexidine (CHX)-added resin blends.

Methods: Blends were formulated: G1)TEGDMA; G2)TEGDMA/0.1%CHX; G3)TEGDMA/0.

Effects of chemical agents on physical properties and structure of primary pulp chamber dentin.

This study evaluated the effects of chemical agents on the physical properties and structure of primary pulp chamber dentin using surface roughness, microhardness tests, and scanning electron microscopy (SEM). Twenty-five primary teeth were sectioned exposing the pulp chamber and were divided into five groups (n = 5): NT, no treatment; SH1, 1% sodium hypochlorite (NaOCl); SH1U, 1% NaOCl + Endo-PTC®; SH1E, 1% NaOCl + 17% EDTA; and E, 17% EDTA. After dentin treatment, the specimens were submitted to roughness, microhardness testing, and SEM analysis.

Biomechanical degradation of the nano-filled resin-modified glass-ionomer surface.

Purpose: To evaluate in the laboratory the roughness (Ra) and micromorphology surface of the nanofilled resin-modified glass-ionomer (Ketac N100) subjected to biomechanical degradation, compared to Vitremer, Ketac Molar Easymix and Fuji IX.

Methods: Specimens obtained from the ionomers were divided into two storage groups (n = 10): relative humidity and S. mutans biofilm (biodegradation).

Marginal adaptation of indirect restorations using different resin coating protocols.

This study evaluated the influence of material combinations used in the resin coating technique (RCT) on the marginal adaptation of indirect restorations with gingival margins in enamel (EM) and cement (CM). Eighty third-molars were used. Two cavities were prepared in each tooth.

In vitro and in vivo investigation of the biological and mechanical behaviour of resin-modified glass-ionomer cement containing chlorhexidine.

Objectives: To evaluate: (1) the in vitro antibacterial, cytotoxic and mechanical properties of a resin-modified glass ionomer cement (RMGIC) containing different concentrations of chlorhexidine (CHX) and (2) the in vivo microbiologic action of the best concentration of CHX associated with the RMGIC applied on remaining dentine after indirect pulp treatment (IPT).

Methods: For the in vitro studies, RMGIC was associated with 0.2, 0.

Effect of thickness of indirect restoration and distance from the light-curing unit tip on the hardness of a dual-cured resin cement.

This study evaluated the Knoop hardness and polymerization depth of a dual-cured resin cement, light-activated at different distances through different thicknesses of composite resin. One bovine incisor was embedded in resin and its buccal surface was flattened. Dentin was covered with PVC film where a mold (0.

Effect of light energy density on conversion degree and hardness of dual-cured resin cement.

This study evaluated the effect of different light energy densities on conversion degree (CD) and Knoop hardness number (KHN) of RelyX ARC (RLX) resin cement. After manipulation according to the manufacturer's instructions, RLX was inserted into a rubber mold (0.8 mm x 5 mm) and covered with a Mylar strip.

In situ and in vitro comparison of laser fluorescence with visual inspection in detecting occlusal caries lesions.

The aim of this study was to compare the in situ and in vitro performances of a laser fluorescence (LF) device (DIAGNOdent 2095) with visual inspection for the detection of occlusal caries in permanent teeth. Sixty-four sites were selected, and visual inspection and LF assessments were carried out, in vitro, three times by two independent examiners, with a 1-week interval between evaluations. Afterwards, the occlusal surfaces were mounted on the palatal portion of removable acrylic orthodontic appliances and placed in six volunteers.

Effect of restorative technique and thermal/mechanical treatment on marginal adaptation and compressive strength of esthetic restorations.

This study evaluated the compressive strength and marginal adaptation of composite onlays using indirect and direct techniques after thermal and mechanical cycling. Onlay standardized cavities were prepared in 50 permanent molars and restored with Z-250 resin composite using indirect (IRT) or direct (DRT) restorative techniques. The restorations were either submitted or not submitted to thermal (500 cycles, 5 degrees to 55 degrees C) and mechanical cycling (50,000 cycles, 50N).

Clinical manifestations and oral findings in Fraser syndrome.

This article is the first known case report of Fraser syndrome in the dental literature. Its purpose was to present the clinical manifestations, oral findings, and dental treatment of a 14-year, 10-month-old female patient. Fraser syndrome is a rare recessive autosomal genetic disorder characterized by multisystemic malformation, usually comprising cryptophthalmos, syndactyly, and renal defects.

In vivo evaluation of laser fluorescence performance using different cut-off limits for occlusal caries detection.

The aim of this in vivo study was to evaluate the performance of laser fluorescence (LF) comparing different cut-off limits for occlusal caries detection. One hundred and thirty first permanent molars were selected. Visual examination and LF assessments were performed independently.