Design and Uncertainty Evaluation of a Calibration Setup for Turbine Blades Vibration Measurement.

Turbomachinery engines face significant failure risks due to the combination of thermal loads and high-amplitude vibrations in turbine and compressor blades. Accurate stress distribution measurements are critical for enhancing the performance and safety of these systems. Blade tip timing (BTT) has emerged as an advanced alternative to traditional measurement methods, capturing blade dynamics by detecting deviations in blade tip arrival times through sensors mounted on the stator casing.

Responsiveness and Precision of Digital IMUs under Linear and Curvilinear Motion Conditions for Local Navigation and Positioning in Advanced Smart Mobility.

Sensors based on MEMS technology, in particular Inertial Measurement Units (IMUs), when installed on vehicles, provide a real-time full estimation of vehicles' state vector (e.g., position, velocity, yaw angle, angular rate, acceleration), which is required for the planning and control of cars' trajectories, as well as managing the in-car local navigation and positioning tasks.

Investigation of the impact of additive manufacturing techniques on the acoustic performance of a coiled-up resonator.

Acoustic metamaterials (AMMs) offer innovative solutions for physics and engineering problems, allowing lighter, multiphysics, and sustainable systems. They are usually studied analytically or numerically and then tested on prototypes. For this reason, additive manufacturing (AM) techniques are a popular way of quickly realising AMMs' innovative geometrical designs.

Highly Reliable Multicomponent MEMS Sensor for Predictive Maintenance Management of Rolling Bearings.

In the field of vibration monitoring and control, the use of low-cost multicomponent MEMS-based accelerometer sensors is nowadays increasingly widespread. Such sensors allow implementing lightweight monitoring systems with low management costs, low power consumption and a small size. However, for the monitoring systems to provide trustworthy and meaningful data, the high accuracy and reliability of sensors are essential requirements.

Research priorities in multiple sclerosis in Latin America: A multi-stakeholder call to action to improve patients care: Research priorities in MS in LATAM.

As human and economic resources are limited, especially in Latin America (LATAM), it is important to identify research priorities to improve multiple sclerosis (MS) patients care in the region. The objective was to generate a multidisciplinary consensus on research priorities in MS for patients care in LATAM by involving healthcare professionals and MS patient associations. METHODS: consensus was reached through a four-step modified Delphi method designed to identify and rate research priorities in MS in LATAM.

Indentation Modulus, Indentation Work and Creep of Metals and Alloys at the Macro-Scale Level: Experimental Insights into the Use of a Primary Vickers Hardness Standard Machine.

In this work, the experimental method and the calculation model for the determination of indentation moduli, indentation work, and indentation creep of metallic materials, by means of macroscale-level forces provided by a primary hardness standard machine at the National Institute of Metrological Research (INRIM) at the at room temperature were described. Indentation moduli were accurately determined from measurements of indentation load, displacement, contact stiffness and hardness indentation imaging and from the slope of the indentation unloading curve by applying the Doerner-Nix linear model; indentation work, representing the mechanical work spent during the force application of the indentation procedure, was determined by calculating the areas under the loading-unloading indentation curve, through fitting experimental data with a polynomial law. Measurements were performed with a pyramidal indenter (Vickers test).

Influence of Classroom Acoustics on Noise Disturbance and Well-Being for First Graders.

Several studies have shown so far that poor acoustics inside classrooms negatively affects the teaching and learning processes, especially at the lowest grades of education. However, the extent to which noise exposure or excessive reverberation affect well-being of children at school in their early childhood is still unanswered, as well as their awareness of noise disturbance. This work is a pilot study to investigate to which extent classroom acoustics affects the perceived well-being and noise disturbance in first graders.

Pressure calibration of a digital microelectromechanical system microphone by comparison.

In the field of noise control and monitoring, a new generation of small and low-cost microelectro-mechanical system (MEMS) microphones is nowadays widely adopted. MEMS microphones, after recognition as traceable measurement instruments, could open up promising measurements based on wireless sensor networks. Current standards do not apply specifically to digital microphones.

Influence of classroom acoustics on the reading speed: A case study on Italian second-graders.

The need of tuning into speech in noisy and reverberant classrooms is a challenge for good speech communication and literacy development at school. Reading development can be compromised if children are exposed to inadequate acoustics, especially those with poor neural processing in speech discrimination. This work reports preliminary results on the influence of classroom acoustics on the reading speed of 94 Italian second-graders.