Hot isostatic pressing as an alternative thermo-mechanical treatment for metallic full-arch implant-supported frameworks obtained by additive and subtractive manufacturing technology: Vertical and horizontal fit, screw removal torque, and stress analysis.

Purpose: To assess vertical and horizontal fit, screw removal torque, and stress analysis (considered biomechanical aspects) of full-arch implant frameworks manufactured in Ti-6Al-4V through milling, and additive manufacturing Direct Metal Laser Sintering (DMLS) and Electron Beam Melting (EBM), and the effect of the thermo-mechanical treatment Hot Isostatic Pressing (HIP) as a post-treatment after manufacturing.

Material And Methods: Maxillary full-arch implant frameworks were made by milling, DMLS, and EBM. The biomechanical assessments were screw removal torque, strain-gauge analyses, and vertical and horizontal marginal fits.

Lactide: Production Routes, Properties, and Applications.

Lactide dimer is an important monomer produced from lactic acid dehydration, followed by the prepolymer depolymerization process, and subsequent purification. As lactic acid is a chiral molecule, lactide can exist in three isomeric forms: L-, D-, and -lactide. Due to its time-consuming synthesis and the need for strict temperature and pressure control, catalyst use, low selectivity, high energy cost, and racemization, the value of a high purity lactide has a high cost in the market; moreover, little is found in scientific articles about the monomer synthesis.

Extracellular matrix-derived and low-cost proteins to improve polyurethane-based scaffolds for vascular grafts.

Vascular graft surgeries are often conducted in trauma cases, which has increased the demand for scaffolds with good biocompatibility profiles. Biodegradable scaffolds resembling the extracellular matrix (ECM) of blood vessels are promising vascular graft materials. In the present study, polyurethane (PU) was blended with ECM proteins collagen and elastin (Col-El) and gelatin (Gel) to produce fibrous scaffolds by using the rotary jet spinning (RJS) technique, and their effects on in vitro properties were evaluated.

Biological performance of a bioabsorbable Poly (L-Lactic Acid) produced in polymerization unit: studies.

The biomaterials engineering goal is to manufacture a biocompatible scaffold that adequately supports or improves tissue regeneration after implantation of the biomaterial in the injured area. Many requirements are demanded for a biomaterial, such as biocompatibility, elasticity, degradation time, and a very important factor is its cost of importation or synthesis, making its application inaccessible to some countries. Studies about biomaterials market show that Polylactic acid (PLLA) is one of the most used polymers, but expensive to produce.

Osseointegration Improvement of Co-Cr-Mo Alloy Produced by Additive Manufacturing.

Cobalt-base alloys (Co-Cr-Mo) are widely employed in dentistry and orthopedic implants due to their biocompatibility, high mechanical strength and wear resistance. The osseointegration of implants can be improved by surface modification techniques. However, complex geometries obtained by additive manufacturing (AM) limits the efficiency of mechanical-based surface modification techniques.

A novel technique to produce tubular scaffolds based on collagen and elastin.

Tubular polymer scaffolds based on tissue engineering techniques have been studied as potential alternatives for vascular regeneration implants. The blood vessels of the cardiovascular system are mainly fibrous, composed of collagen (Col) and elastin (El), and its inner layer consists of endothelial cells. In this work, Col and El were combined with polyurethane (PU), a biocompatible synthetic polymer, and rotary jet spinning, a new and highly productive technique, to produce fibrous scaffolds.

An assessment of biomedical CoCrMo alloy fabricated by direct metal laser sintering technique for implant applications.

CoCrMo alloys have been used for several decades in implantable devices due to their favourable mechanical properties, low wear rate in addition to good biocompatibility and high corrosion resistance. These alloys are conventionally produced via casting and/or forging route, however additive manufacturing techniques being recently employed in their fabrication. In this work, CoCrMo samples were produced by direct metal laser sintering additive manufacturing process.

Regenerative collagen biomembrane: Interim results of a Phase I veterinary clinical trial for skin repair.

The availability of commercial tissue engineering skin repair products for veterinary use is scarce or non-existent. To assess features of novel veterinary tissue engineered medical devices, it is therefore reasonable to compare with currently available human devices. During the development and regulatory approval phases, human medical devices that may have been identified as comparable to a novel veterinary device, may serve as predicate devices and accelerate approval in the veterinary domain.

Cardiac tissue engineering: current state-of-the-art materials, cells and tissue formation.

Cardiovascular diseases are the major cause of death worldwide. The heart has limited capacity of regeneration, therefore, transplantation is the only solution in some cases despite presenting many disadvantages. Tissue engineering has been considered the ideal strategy for regenerative medicine in cardiology.

3D-Printed Craniosynostosis Model: New Simulation Surgical Tool.

Background: Craniosynostosis is a complex disease once it involves deep anatomic perception, and a minor mistake during surgery can be fatal. The objective of this report is to present novel 3-dimensional-printed polyamide craniosynostosis models that can improve the understanding and treatment complex pathologies.

Methods: The software InVesalius was used for segmentation of the anatomy image (from 3 patients between 6 and 9 months old).

Electrospun polyurethane membranes for Tissue Engineering applications.

Tissue Engineering proposes, among other things, tissue regeneration using scaffolds integrated with biological molecules, growth factors or cells for such regeneration. In this research, polyurethane membranes were prepared using the electrospinning technique in order to obtain membranes to be applied in Tissue Engineering, such as epithelial, drug delivery or cardiac applications. The influence of fibers on the structure and morphology of the membranes was studied using scanning electron microscopy (SEM), the structure was evaluated by Fourier transform infrared spectroscopy (FT-IR), and the thermal stability was analyzed by thermogravimetry analysis (TGA).

Bio-based polyurethane for tissue engineering applications: How hydroxyapatite nanoparticles influence the structure, thermal and biological behavior of polyurethane composites.

In this work, thermoset polyurethane composites were prepared by the addition of hydroxyapatite nanoparticles using the reactants polyol polyether and an aliphatic diisocyanate. The polyol employed in this study was extracted from the Euterpe oleracea Mart. seeds from the Amazon Region of Brazil.

Cranial reconstruction: 3D biomodel and custom-built implant created using additive manufacturing.

Additive manufacturing (AM) technology from engineering has helped to achieve several advances in the medical field, particularly as far as fabrication of implants is concerned. The use of AM has made it possible to carry out surgical planning and simulation using a three-dimensional physical model which accurately represents the patient's anatomy. AM technology enables the production of models and implants directly from a 3D virtual model, facilitating surgical procedures and reducing risks.

Poly-lactic acid synthesis for application in biomedical devices - a review.

Bioabsorbable polymers are considered a suitable alternative to the improvement and development of numerous applications in medicine. Poly-lactic acid (PLA,) is one of the most promising biopolymers due to the fact that the monomers may produced from non toxic renewable feedstock as well as is naturally occurring organic acid. Lactic acid can be made by fermentation of sugars obtained from renewable resources as such sugarcane.