Evaporative and Wicking Functionalities at Hot Airflows of Laser Nano-/Microstructured Ti-6Al-4V Material.

A novel multifunctional material with efficient wicking and evaporative functionalities was fabricated using hierarchical surface nano-/microstructuring by femtosecond laser micromachining. The created material exhibits excellent multifunctional performance. Our experiments in a wind tunnel demonstrate its good wicking and evaporative functionalities under the conditions of high-temperature airflows.

Superwicking Functionality of Femtosecond Laser Textured Aluminum at High Temperatures.

An advanced superwicking aluminum material based on a microgroove surface structure textured with both laser-induced periodic surface structures and fine microholes was produced by direct femtosecond laser nano/microstructuring technology. The created material demonstrates excellent wicking performance in a temperature range of 23 to 120 °C. The experiments on wicking dynamics show a record-high velocity of water spreading that achieves about 450 mm/s at 23 °C and 320 mm/s at 120 °C when the spreading water undergoes intensive boiling.

Spreading and Drying Dynamics of Water Drop on Hot Surface of Superwicking Ti-6Al-4V Alloy Material Fabricated by Femtosecond Laser.

A superwicking Ti-6Al-4V alloy material with a hierarchical capillary surface structure was fabricated using femtosecond laser. The basic capillary surface structure is an array of micropillars/microholes. For enhancing its capillary action, the surface of the micropillars/microholes is additionally structured by regular fine microgrooves using a technique of laser-induced periodic surface structures (LIPSS), providing an extremely strong capillary action in a temperature range between 23 °C and 80 °C.

Temperature Effect on Capillary Flow Dynamics in 1D Array of Open Nanotextured Microchannels Produced by Femtosecond Laser on Silicon.

Capillary flow of water in an array of open nanotextured microgrooves fabricated by femtosecond laser processing of silicon is studied as a function of temperature using high-speed video recording. In a temperature range of 23-80 °C, the produced wicking material provides extremely fast liquid flow with a maximum velocity of 37 cm/s in the initial spreading stage prior to visco-inertial regime. The capillary performance of the material enhances with increasing temperature in the inertial, visco-inertial, and partially in Washburn flow regimes.

Optical Third Harmonic Generation Using Nickel Nanostructure-Covered Microcube Structures.

We investigated the optical third harmonic generation (THG) signal from nanostructure-covered microcubes on Ni. We found that the hierarchical structures greatly change the third-order optical nonlinearity of the metallic surface. While the symmetry and lightning rod (LR) effects on microstructures did not significantly influence the THG, the localized surface plasmon (LSP) effect on the nanostructures enhanced it.

Direct visualization of the complete evolution of femtosecond laser-induced surface structural dynamics of metals.

Despite extensive studies of femtosecond laser-material interactions, even the simplest morphological responses following femtosecond pulse irradiation have not been fully resolved. Past studies have revealed only partial dynamics. Here we develop a zero-background and high-contrast scattered-light-based optical imaging technique through which we capture, for the first time, the complete temporal and spatial evolution of the femtosecond laser-induced morphological surface structural dynamics of metals from start to finish, that is, from the initial transient surface fluctuations, through melting and ablation, to the end of resolidification.

[Influence of intra-pulpal temperature when using femtosecond laser in specific parameters to prepare cavities in tooth enamel: an in vitro study].

Objective: To take the Real-time measurement of the intra-pulpal temperature (IPT) when using femtosecond laser in specific parameters to prepare cavities in tooth enamel in vitro, and to preliminarily evaluate the effect of air cooling.

Methods: All pulp champers of extracted human teeth (premolars and molars) were exposed by roots amputated and pulp scraped out. All chambers were tightly filled with copper powder, and thermocouple was inserted into the center of the powder stack.

[Femtosecond pulsed laser ablation of dental hard tissues with numerical control: a roughness and morphology study].

Objective: To establish the femtosecond laser experimental platform in vitro for numerical controlled cavity preparation, and to evaluate the roughness quantitatively and observe the microscopic morphology of the cutting surface.

Methods: Enamel and dentin planes were prepared on human third molars. A universal motion controller was used to control the samples to do rectangle wave motion perpendicular to the incident direction of the laser at focus.