Single-Atomic Dispersion of Fe and Co Supported on Reduced Graphene Oxide for High-Performance Lithium-Sulfur Batteries.

High theoretical energy density and low cost make lithium-sulfur (LSB) batteries a promising system for next-generation energy storage. LSB performance largely depends on efficient reversible conversion of elemental sulfur to LiS. Here, well-designed sulfur host materials including Fe or Co single atoms embedded on N-doped reduced graphene oxide (MNC/G with M = Fe or Co) are proposed to tackle the LSB challenges and enhance the electrochemical performance.

Investigating the abnormal conductivity behaviour of divalent cations in low dielectric constant tetraglyme-based electrolytes.

Solutions made of tetraglyme (G4) containing Ca(TFSI) have been studied as models to understand the solvation structure and the conductivity properties of multivalent ions in low dielectric constant ethereal electrolytes. These solutions have been characterised using electrochemical impedance spectroscopy, rheological measurement, and Raman spectroscopy. The ionic conductivity of these electrolytes shows an intriguing non-monotonic behaviour with temperature which deviates from the semi-empirical Vogel-Tammann-Fulcher equation at a critical temperature.

Pristine and Modified Porous Membranes for Zinc Slurry-Air Flow Battery.

The membrane is a crucial component of Zn slurry-air flow battery since it provides ionic conductivity between the electrodes while avoiding the mixing of the two compartments. Herein, six commercial membranes (Cellophane™ 350PØØ, Zirfon, Fumatech PBI, Celgard 3501, 3401 and 5550) were first characterized in terms of electrolyte uptake, ion conductivity and zincate ion crossover, and tested in Zn slurry-air flow battery. The peak power density of the battery employing the membranes was found to depend on the in-situ cell resistance.

Study of Anion Exchange Membrane Properties Incorporating -spirocyclic Quaternary Ammonium Cations and Aqueous Organic Redox Flow Battery Performance.

Flexible cross-linked anion exchange membranes (AEMs) based on poly (-phenylene oxide) grafted with -spirocyclic quaternary ammonium cations were synthesized via UV-induced free-radical polymerization by using diallylpiperidinium chloride as an ionic monomer. Five membranes with ion exchange capacity (IEC) varying between 1.5 to 2.

Fingerprinting Mean Composition of Lithium Polysulfide Standard Solutions by Applying High-Energy Resolution Fluorescence Detected X-ray Absorption Spectroscopy.

In a lithium/sulfur (Li/S) battery, the reduction of sulfur during discharge involves a particular mechanism, where the active material successively dissolves into the electrolyte to form lithium polysulfide intermediate species (LiS), with being a function of the state of charge. In this work, sulfur K-edge resonant inelastic X-ray scattering measurements were performed for the characterization of different LiS polysulfide standard solutions. High-energy resolution fluorescence detected X-ray absorption spectroscopy allowed clear separation the pre-edge absorption peak corresponding to terminal sulfur atoms from the main absorption peak due to internal atoms and allowed quantitative evaluation of the evolution of the peak area ratio as a function of the polysulfide chain length.

Use of Cellulose Nanofibers as an Electrode Binder for Lithium Ion Battery Screen Printing on a Paper Separator.

Water-based inks were formulated using cellulose nanofibers as a binder in order to directly front/reverse print lithium ion cells on a paper separator. Moreover, the high cohesion of electrodes as provided by cellulose nanofibers allowed for the embedding metallic current collectors in the electrodes during the printing stage, in order to develop a one-step printing and assembling process. Positive and negative inks based on LiFePO₄, or graphite, respectively, and cellulose nanofibers, displayed rheological properties complying with a variety of printing processes, as well as with screen printing.

Magnesium Anthracene System-Based Electrolyte as a Promoter of High Electrochemical Performance Rechargeable Magnesium Batteries.

The development of efficient, inexpensive, and safe rechargeable batteries for large-scale environmentally benign cells is one of the key requirements to accommodate and satisfy various technological applications. To date, the development of magnesium battery as a promising candidate for next-generation battery systems has been hindered by the lack of high performance and stable electrolyte. In this work, we have developed an original, safe, and high-performance class of electrolytes based on a simple mixture of commercially available compounds, that is, Mg(TFSI), anthracene, MgCl, and diglyme solvent.

Electrolyte Based on Easily Synthesized, Low Cost Triphenolate-Borohydride Salt for High Performance Mg(TFSI)-Glyme Rechargeable Magnesium Batteries.

A new class of electrolyte based on TFSI and triphenolate-borohydride anions was designed and produced which fulfill all requirements of easy synthesis, high ionic conductivity, wide potential window, and noncorrosion of Al current collector. The electrolyte composed of magnesium triphenolate borohydride and Mg(TFSI) in glyme simultaneously displays a high conductivity of 5.5 mS cm at 25 °C and a reversible Mg plating/stripping with high current density and Coulombic efficiency at room temperature.

Degradation of Li/S Battery Electrodes On 3D Current Collectors Studied Using X-ray Phase Contrast Tomography.

Lithium/sulphur batteries are promising candidates for future energy storage systems, mainly due to their high potential capacity. However low sulphur utilization and capacity fading hinder practical realizations. In order to improve understanding of the system, we investigate Li/S electrode morphology changes for different ageing steps, using X-ray phase contrast tomography.

Enabling LiTFSI-based electrolytes for safer lithium-ion batteries by using linear fluorinated carbonates as (Co)solvent.

In this Full Paper we show that the use of lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) as conducting salt in commercial lithium-ion batteries is made possible by introducing fluorinated linear carbonates as electrolyte (co)solvents. Electrolyte compositions based on LiTFSI and fluorinated carbonates were characterized regarding their ionic conductivity and electrochemical stability towards oxidation and with respect to their ability to form a protective film of aluminum fluoride on the aluminum surface. Moreover, the investigation of the electrochemical performance of standard lithium-ion anodes (graphite) and cathodes (Li[Ni1/3 Mn1/3 Co1/3 ]O2 , NMC) in half-cell configuration showed stable cycle life and good rate capability.

New insight into the working mechanism of lithium-sulfur batteries: in situ and operando X-ray diffraction characterization.

In order to improve the electrochemical performances of lithium-sulfur batteries, it is crucial to understand profoundly their working mechanism and the limitation factors. This communication presents synchrotron-based in situ XRD studies of structural modifications occurring inside the cell upon cycling, since the active material changes constantly its form between solid and liquid phases.

Lithium/sulfur cell discharge mechanism: an original approach for intermediate species identification.

The lithium/sulfur battery is a promising electrochemical system that has a high theoretical capacity of 1675 mAh g(-1), but its discharge mechanism is well-known to be a complex multistep process. As the active material dissolves during cycling, this discharge mechanism was investigated through the electrolyte characterization. Using high-performance liquid chromatography, UV-visible absorption, and electron spin resonance spectroscopies, we investigated the electrolyte composition at different discharge potentials in a TEGDME-based electrolyte.

Structure-properties relationships of lithium electrolytes based on ionic liquid.

Low-melting ionic liquid, IL, based on small aliphatic quaternary ammonium cations ([R(1)R(2)R(3)NR](+), where R(1), R(2), R(3) = CH(3) or C(2)H(5), R = C(3)H(7), C(4)H(9), C(6)H(13), C(8)H(17), CF(3)C(3)H(6)) and imide anion were prepared and characterized. The physicochemical and electrochemical properties of these ILs, including melting point, glass transition, and degradation temperatures; viscosity; density; ionic conductivity; diffusion coefficient; and electrochemical stability, were determined. Heteronuclear Overhauser NMR spectroscopy experiments were also performed to point out the presence of pair correlation between the different moieties.

Temperature-dependent raman spectroscopy of lithium triflate-PEO complexes: phase equilibrium and component interactions.

Poly(ethylene oxide) and complexes of lithium trifluorosulfonate-poly(ethylene oxide) (LiTf-PEO) with 4 View Article and Find Full Text PDF

Polyepichlorhydrin membranes for alkaline fuel cells: sorption and conduction properties.

Polymer electrolytes, using a poly(epichlorhydrin-allyl glycidyl ether) copolymer as matrix, are shown to perform well in alkaline fuel cell electrolyte. An anion-conducting network is obtained by the incorporation of cyclic diamines, 1,4-diazabicyclo[2.2.

NMR and electrochemical study on lithium oligoether sulfate in polymeric and liquid electrolytes.

Electrolytes based on lithium oligoether sulfate, and dissolved in liquid or polymer solvents, are studied. Their properties in term of ionic conductivities, transference numbers, diffusion coefficients, and electrochemical stabilities are reported. The comparison between NMR and electrochemical data, that is, transference numbers and conductivities, provides important information about the existence of ion pairs and aggregates.

NMR study of cation, anion, and solvent mobilities in macroporous poly(vinylidene fluoride).

The mobilities of lithium, PF6- and solvents in the electrolyte LiPF6-(ethylene carbonate-dimethyl carbonate-diethyl carbonate) were measured using the pulsed gradient spin-echo NMR. They were compared to those of the same electrolyte filling a macroporous poly(vinylidene fluoride) membrane. The conductivity decrease resulting in the incorporation of this macroporous membrane and the cationic transport number were analyzed in terms of (i) solvent/polymer and solvent/salt interactions, (ii) ionic dissociation, and (iii) tortuosity.

Review of recent research into cellulosic whiskers, their properties and their application in nanocomposite field.

There are numerous examples where animals or plants synthesize extracellular high-performance skeletal biocomposites consisting of a matrix reinforced by fibrous biopolymers. Cellulose, the world's most abundant natural, renewable, biodegradable polymer, is a classical example of these reinforcing elements, which occur as whisker-like microfibrils that are biosynthesized and deposited in a continuous fashion. In many cases, this mode of biogenesis leads to crystalline microfibrils that are almost defect-free, with the consequence of axial physical properties approaching those of perfect crystals.