Bond strengths of a self-etching adhesive to dentin surfaces treated with saliva, blood, and different hemostatic agents.

The aim of this study was to evaluate the microtensile bond strengths of a self-etching adhesive to dentin surfaces after treatment with 4 different hemostatic agents in the presence of saliva and blood. After testing, no significant differences were found between the mean bond strength of Clearfil SE (CSE) Bond resin adhesive to normal dentin and those of CSE to dentin treated with the hemostatic agents ViscoStat Clear, Astringedent, or Astringedent X (P > 0.05).

Elution of monomer from different bulk fill dental composite resins.

Objective: The purpose of this study was to evaluate the elution of Bis-GMA, TEGDMA, HEMA, and Bis-EMA monomers from six bulk fill composite resins over four different time periods, using HPLC.

Methods: Six different composite resin materials were used in the present study: Tetric Evo Ceram Bulk Fill (Ivoclar Vivadent, Amherst, NY), X-tra Fill (VOCO, Cuxhaven, Germany), Sonic Fill (Kerr, Orange, CA, USA), Filtek Bulk Fill (3M ESPE Dental Product, St. Paul, MN), SDR (Dentsply, Konstanz, Germany), EQUIA (GC America INC, Alsip, IL).

Effect of accelerated aging on the bonding performance of fluoridated adhesive resins.

The purpose of this study was to investigate the dentin bond durability of a one-step, fluoride-containing, glass ionomer-based adhesive system, Reactmer Bond (RB), and that of a two-step, fluoride-containing, self-etch adhesive system, Clearfil Protect Bond (CPB). Enamel was removed from the occlusal surfaces of teeth, and flat dentin surfaces were entirely covered with a composite resin following the application of an adhesive material (n=10). After specimens were sectioned into rectangular sticks of 0.

Conversion degrees of resin composites using different light sources.

Objective: The objective of this study was to compare the conversion degree of six different composite materials (Filtek Z 250, Filtek P60, Spectrum TPH, Pertac II, Clearfil AP-X, and Clearfil Photo Posterior) using three different light sources (blue light-emitting diode [LED], plasma arc curing [PAC], and conventional halogen lamp [QTH]).

Methods: Composites were placed in a 2 mm thick and 5 mm diameter Teflon molds and light cured from the top using three methods: LED for 40 s, PAC for 10 s, and QTH for 40 s. A Fourier Transform Infrared Spectroscopy (FTIR) was used to evaluate the degree of conversion (DC) (n=5).

The effect of luting cement thicknesses on the push-out bond strength of the fiber posts.

Objective: The aim of this study was to evaluate the effect of luting cement thicknesses on the push-out bond strength of the fiber posts.

Materials And Methods: Sixty human maxillary canine teeth were endodontically treated. Post spaces were prepared and root specimens randomly divided into three groups: Group 1: etch-and-rinse (Variolink II/Exite DSC), Group 2: self-etch (Panavia F2.

Influence of eugenol on the push-out bond strengths of fiber posts cemented with different types of resin luting agents.

This study evaluated the influence of eugenol on the push-out bond strengths of fiber posts cemented with different types of resin luting agents. Seventy-two extracted maxillary single-rooted canine teeth were randomly divided into two groups of 36 teeth. Group 1, the control group, was filled with gutta-percha only (i.

Clinical wear rate of direct and indirect posterior composite resin restorations.

The purpose of this randomized clinical trial was to determine the clinical wear behavior of three nanofilled composites (Filtek Supreme XT [FS], Tetric EvoCeram [TEC], and Aelite Aesthetic [AA]) with two indirect composites (Estenia [E] and Tescera ATL [TATL]) on permanent molar teeth. Fifty-four patients whose treatment plans included moderate Class I and/or II restorations on molar teeth were selected for inclusion in this study. Wear was measured by use of gypsum replicas at baseline and 6 and 12 months using three-dimensional scanning and rapid-form software to elucidate the wear mechanisms.

An in vitro comparison of different diagnostic methods in detection of residual dentinal caries.

The aim of this study was to investigate the efficiency of different diagnostic methods in detection of residual dentinal caries in excavated cavities. Fifty extracted molar with deep dentinal carious lesions were excavated using a slow-speed handpiece. All cavities were assessed by laser fluorescence(LF) device, electronic caries monitor(ECM), and caries detector dye(CDD) by three independent observers blindly.

One-year clinical evaluation of direct nanofilled and indirect composite restorations in posterior teeth.

The aim of this study was to assess the clinical performance of three direct composite resins and two indirect inlay systems in posterior teeth using the modified USPHS criteria. A total of 100 restorations were placed in the molars of 54 patients by one operator. All restorations were directly evaluated by two examiners at baseline, 6 months, and 12 months.

The effect of different restoration techniques on the fracture resistance of endodontically-treated molars.

Aim: This study compared the fracture resistance of endodontically-treated mandibular molars with mesio-occluso-distal (MOD) cavities restored using different restoration techniques.

Methodology: Sixty sound extracted mandibular molars were randomly assigned to six groups (n=10). Group 1 did not receive any preparation.