The objective was to determine the degree of fluctuating asymmetry in the expression of 13 dental morphological traits among adult Jordanians. Cone beam computed tomography images for the dentitions of 150 adult Jordanians (67 males, 83 females; age range = 18-58, mean ages 28.2, SD = 10.
View Article and Find Full Text PDFObjectives: To investigate the effect of toothpaste abrasive level on the progression of non-carious cervical lesions (NCCLs) using 3D-image subtraction.
Methods: Upper first premolars were allocated into seven groups (n = 16) of toothpaste/abrasive slurries: A-Zeodent113/5%, B-Zeodent124/10%, C-Zeodent103/15%, D-Sensodyne Pronamel, E-Crest Cavity-Protection, F-Crest Pro-Health-Whitening, and G-Deionized water (DIW). Teeth were mounted on acrylic blocks, and their root surfaces covered with acrylic resin, except for 2-mm near the cemento-enamel junction that was exposed to toothbrushing.
Objectives: To determine the combined effect of fatigue cyclic loading and thermocycling (CLTC) on the shear bond strength (SBS) of a resin cement to zirconia surfaces that were previously air-abraded with aluminum oxide (AlO) particles at different pressures.
Materials And Methods: Seventy-two cuboid zirconia specimens were prepared and randomly assigned to 3 groups according to the air-abrasion pressures (1, 2, and 2.8 bar), and each group was further divided into 2 groups depending on aging parameters ( = 12).
Introduction: The aim of this study was to investigate the residual antibacterial effect of human radicular dentin treated with various concentrations of triple antibiotic paste and double antibiotic paste (DAP).
Methods: Sterilized dentin specimens were randomly assigned to 6 treatment groups and a no-treatment control group (n = 45 per group). For treatment groups, specimens were treated with either TAP or DAP at various concentrations (1000, 1, or 0.
Introduction: We investigated the changes in physiochemical properties of dentin surfaces after performing different endodontic regeneration protocols.
Methods: Human dentin slices were randomized into 4 treatment groups and 1 untreated control group (n = 10). One treatment group was irrigated with sodium hypochlorite (NaOCl) for 5 minutes followed by EDTA for 10 minutes.
Objectives: To investigate the effect of various dilutions of antibiotic medicaments used in endodontic regeneration on the survival of human dental pulp stem cells (DPSCs) and to determine their antibacterial effect against established Enterococcus faecalis biofilm.
Materials And Methods: The cytotoxic and antibacterial effects of different triple (TAP) and double antibiotic paste (DAP) dilutions (0.125, 0.
Objective: To determine the influence of socioeconomic status (SES) on normative and perceived orthodontic treatment need, satisfaction with dental appearance, and regularity of dental attendance.
Materials And Methods: The sample consisted of 550 adolescents (232 boys, 318 girls) aged 13 to 17 years who were categorized according to SES into three groups: low, middle, and high SES. Normative treatment need was assessed by using the Index of Orthodontic Treatment Need.
Introduction: In this study we compared the antibacterial effect of triple antibiotic paste (TAP), double antibiotic paste (DAP), and calcium hydroxide [Ca(OH)2] against Enterococcus faecalis and Porphyromonas gingivalis biofilm.
Methods: The minimum inhibitory concentration (MIC), minimum bactericidal concentration (MBC), minimum biofilm inhibitory concentration (MBIC), and biofilm formation were measured by using microtiter plate methods. The 2 bacteria were treated with different dilutions of TAP, DAP, and Ca(OH)2 solutions.
Purpose: The purpose of this study was to evaluate the influence of full-contour (Y-TZP) zirconia surface roughness (glazed vs. as-machined) on the wear behavior of glass-ceramics.
Materials And Methods: Thirty-two full contour Y-TZP (Diazir®) specimens (hereafter referred to as zirconia sliders) (ϕ = 2 mm, 1.
Objective: To investigate the effects of polishing techniques on the surface roughness of Y-TZP ceramic and on the wear behavior of synthetic hydroxyapatite (HA).
Methods: Thirty-two full-contour Y-TZP (Diazir(®)) sliders (φ=2 mm × 1.5 mm in height) were manufactured using CAD/CAM, embedded in acrylic resin using brass holders, and randomly allocated into four groups (n=8): according to the finishing/polishing procedure: G1-as-machined, G2-glazed, G3-diamond bur finishing and G4-G3+OptraFine(®) polishing kit.