Influence of sandblasting and bonding on the shear bond strength between differently pigmented polyetheretherketone (PEEK) and veneering composite after artificial aging.

Objective: Achieving a strong bond between Polyetheretherketone (PEEK) and veneering composites is challenging due to PEEKs low surface energy. This study examined the effects of sandblasting and bonding on the shear bond strength (SBS) between veneering composite and pigmented PEEK, considering artificial aging.

Methods: Of three pigmented PEEK compounds (DC4420R, DC4450R, DC4470R; Evonic Operations GmbH, Marl, Germany), 40 specimens each were milled and polished up to 2500 grit.

Esthetic and functional rehabilitation of a patient with a bilateral cleft of lip, alveolar process, and palate with anterior all-ceramic cantilever resin-bonded fixed dental prostheses.

Objectives: Addressing a single-tooth gap in the anterior region, resulting from aplasia or trauma, poses both esthetic and functional challenges. This case report presents the restoration of a young adult with a cleft, exhibiting anterior hypoplasia and aplasia in the canine and incisor regions, using all-ceramic cantilever resin-bonded fixed dental prostheses.

Method And Materials: After verification of esthetic and functional considerations through a diagnostic wax-up and an intraoral mock-up, three anterior all-ceramic cantilever resin-bonded fixed dental prostheses made of veneered zirconium dioxide were planned in the region of the maxillary right lateral incisor and maxillary left canine.

Effect of apical root resection, orthodontic extrusion, and surgical crown lengthening on load capability.

Objectives: This study aims to investigate the load-to-fracture of procedures changing crown-to-root ratio (R) aimed to restore severely damaged upper central incisors to avoid tooth extraction compared to implant placement. There is no evidence on load capability after apical root resection (AR), orthodontic extrusion (OE), and surgical crown lengthening (SCL) in respect to R, respectively.

Material And Methods: Human maxillary central incisors were endodontically treated, decoronated, and divided into 4 groups (n = 48).

Survival and success of veneered zirconia crowns.

Aim: The aim of the present study was to evaluate the long-term clinical survival and success rate of veneered zirconia crowns with a modified anatomical framework design after 10 years in function.

Materials And Methods: In total, 36 zirconia crowns were fabricated for 28 patients. An anatomically modified framework design was developed.

Replica denture technique: improvements through the use of CAD/CAM technology.

The majority of complete dentures are not initially made for the rehabilitation of an edentulous jaw; in most cases, they replace an existing complete denture. Since the ability to adapt to a new complete denture decreases with age, the replica denture procedure represents a smart opportunity. The aim is to copy the clinically successful parts of the old prosthesis and to change the destroyed parts.

Measured accuracy of intraoral scanners is highly dependent on methodical factors.

Purpose: The accuracy of intraoral and model scanners has been widely investigated with heterogeneous results, but the impact of the applied diversity of measurement methods on the outcomes remains unknown. This study aimed to evaluate the influence of methodological factors on the measurement result when comparing full-arch scans.

Methods: The evaluation referred to a 5M model to analyze whether accuracy measurements are affected by (1) the reference geometry, (2) mesh density of the standard tessellation language (STL) datasets, (3) operator, (4) inspection software, and (5) alignment procedure.

Bond strength of conventional, subtractive, and additive manufactured denture bases to soft and hard relining materials.

Objective: To investigate the tensile and flexural strength of poured, subtractive, and additive manufactured denture base methacrylates bonded to soft and hard relining materials after hydrothermal cycling and microwave irradiation.

Methods: This study included a conventional (CB), subtractive (SB), and additive (AB) base material as well as a soft (SCR) and hard (HCR) chairside and one hard laboratory-side (HLR) relining material. Reference bodies of the base materials and bonded specimens to the relining materials were produced with a rectangular cross-section.

Accuracy and its impact on fit of injection molded, milled and additively manufactured occlusal splints.

Occlusal devices to reduce symptoms of bruxism and temperomandibular disorders can nowadays be manufactured in a digital workflow but studies comparing the accuracy of those occlusal devices are still limited. Therefore, the aim of this investigation was to investigate the accuracy of injection molding compared with four computer-aided design (CAD) and computer-aided manufacturing (CAM) techniques for the manufacturing of occlusal devices. In addition, the number of contact points and retention were evaluated to assess clinical relevance.

Do hydrothermal aging and microwave sterilization affect the trueness of milled, additive manufactured and injection molded denture bases?

Concepts for digital denture manufacturing are market-available but studies comparing the trueness of such dentures, either milled (MIL) or additive manufactured, compared to injection molded (IM) ones are still limited. Regarding the impact of artificial aging and microwave sterilization on this parameter, no data are available. Therefore, the purpose of this investigation was to assess the trueness of IM, MIL, and stereolithography (SLA) printed denture bases after manufacturing, hydrothermal cycling, and microwave sterilization.

Bacterial leakage and bending moments of screw-retained, composite-veneered PEEK implant crowns.

Due to its elastic modulus close to bone, the high-performance material PEEK (polyetheretherketone) represents an interesting material for implant-supported dental prostheses. Besides a damping effect of masticatory forces, it might have a sealing effect against bacterial leakage of the implant-abutment interface (IAI). So far, PEEK has only been used for provisional implant crowns.

Digital Impression-Taking Facilitates Prosthetic Rehabilitation of Microstomia Patients: A Case History Report.

In most cases, prosthetic rehabilitation of patients suffering from microstomia is inconvenient for the patient and challenging for both the dentist and dental technician. In such cases, conventional impression-taking requires an individualized tray design and modified impression techniques, amplifying the risk for impression and cast deformation and thereby compromising the final outcome. An intraoral scanner (IOS) might overcome these limitations due to its reduced size compared to an impression tray.