Effect of Processing Route on Microstructure and Mechanical Properties of an Al-12Si Alloy.

Two different microstructures of an Al-12Si (wt. %) alloy were produced, respectively, via a powder laser bed fusion (P-LBF) additive manufacturing and casting. Compared to casting, additive manufacturing of Al-based alloy requires extra care to minimize oxidation tendency.

Non-Invasive Brain Sensing Technologies for Modulation of Neurological Disorders.

The non-invasive brain sensing modulation technology field is experiencing rapid development, with new techniques constantly emerging. This study delves into the field of non-invasive brain neuromodulation, a safer and potentially effective approach for treating a spectrum of neurological and psychiatric disorders. Unlike traditional deep brain stimulation (DBS) surgery, non-invasive techniques employ ultrasound, electrical currents, and electromagnetic field stimulation to stimulate the brain from outside the skull, thereby eliminating surgery risks and enhancing patient comfort.

Micro-Scale Deformation Aspects of Additively Fabricated Stainless Steel 316L under Compression.

The deformation aspects associated with the micro-mechanical properties of the powder laser bed fusion (P-LBF) additively manufactured stainless steel 316L were investigated in the present work. Toward that, micro-pillars were fabricated on different planes of the stainless steel 316L specimen with respect to build direction, and an in situ compression was carried out inside the chamber of the scanning electron microscope (SEM). The results were compared against the compositionally similar stainless steel 316L, which was fabricated by a conventional method, that is, casting.

Microstructural and Nanoindentation Investigation on the Laser Powder Bed Fusion Stainless Steel 316L.

Additive manufacturing (AM) of stainless steel is more difficult than other metallic materials, as the major alloying elements of the stainless steel are prone to oxidation during the fabrication process. In the current work, specimens of the stainless steel 316L were made by the powder laser bed fusion (P-LBF) additive manufacturing process. These specimens were investigated by electron microscopy and micro-/nano-indentation techniques to investigate the microstructural aspects and the mechanical properties, respectively.

Investigation into the Microstructure and Hardness of Additively Manufactured (3D-Printed) Inconel 718 Alloy.

Additive manufacturing (AM) of Ni-based super alloys is more challenging, compared to the production other metallic alloys. This is due to their high melting point and excellent high temperature resistance. In the present work, an Inconel 718 alloy was fabricated by a powder laser bed fusion (P-LBF) process and investigated to assess its microstructural evolution, together with mechanical properties.

Formation and Characterization of the Recast Layer Formed on Inconel 718 during Wire Electro Discharge Machining.

The present work investigates the formation and microstructural and micro-mechanical characterization of the recast layer that formed on Inconel 718 alloy in the course of the wire electro-discharge machining (WEDM). The as-machined surface contains globules, shallow cracks, and re-deposition of molten materials, together with the elements from the decomposition of wire electrode and electrolyte, which does not exceed beyond the surface of the recast layer. Under presently investigated machining parameters, the recast layer was about 6.

The Effect of Body Mass Index on the Degree of Renal Interstitial Fibrosis and Tubular Atrophy - A Retrospective Case-Control Study.

Introduction The degree of interstitial fibrosis and tubular atrophy (IFTA) seen on kidney biopsy has long been used to judge the chronicity of kidney disease to predict renal disease outcomes and prognosis. It is an essential component incorporated in many renal disease prognostic classification systems on the native and renal allograft. The impact of increased body mass index on the body metabolism, and the human vascular system, including the functional unit of the kidney, the nephron, is well-addressed in the literature.

Potential Phase Change Materials in Building Wall Construction-A Review.

Phase change materials (PCMs) are an effective thermal mass and their integration into the structure of a building can reduce the ongoing costs of building operation, such as daily heating/cooling. PCMs as a thermal mass can absorb and retard heat loss to the building interior, maintaining comfort in the building. Although a large number of PCMs have been reported in the literature, only a handful of them, with their respective advantages and disadvantages, are suitable for building wall construction.

Practice of Simulation and Life Cycle Assessment in Tribology-A Review.

To simulate today's complex tribo-contact scenarios, a methodological breakdown of a complex design problem into simpler sub-problems is essential to achieve acceptable simulation outcomes. This also helps to manage iterative, hierarchical systems within given computational power. In this paper, the authors reviewed recent trends of simulation practices in tribology to model tribo-contact scenario and life cycle assessment (LCA) with the help of simulation.