Molecularly Smooth Self-Assembled Monolayer for High-Mobility Organic Field-Effect Transistors.

Despite the need for molecularly smooth self-assembled monolayers (SAMs) on silicon dioxide surfaces (the most common dielectric surface), current techniques are limited to nonideal silane grafting. Here, we show unique bioinspired zwitterionic molecules forming a molecularly smooth and uniformly thin SAM in "water" in <1 min on various dielectric surfaces, which enables a dip-coating process that is essential for organic electronics to become reality. This monomolecular layer leads to high mobility of organic field-effect transistors (OFETs) based on various organic semiconductors and source/drain electrodes.

Further correction: Low bandgap semiconducting polymers for polymeric photovoltaics.

Further correction for 'Low bandgap semiconducting polymers for polymeric photovoltaics' by Chang Liu et al., Chem. Soc.

Dithienogermole-based solution-processed molecular solar cells with efficiency over 9.

A molecular donor of intermediate dimensions based on dithienogermole (DTG) as the central electron rich unit, coded as DTG(FBT2Th2)2, was designed and synthesized for use in bulk heterojunction, solution-processed organic solar cells. Under optimized conditions, a maximum power conversion efficiency (PCE) of 9.1% can be achieved with [6,6]-phenyl C71-butyric acid methyl ester (PC71BM) as the acceptor semiconductor component.

High-Performance Electron Acceptor with Thienyl Side Chains for Organic Photovoltaics.

We develop an efficient fused-ring electron acceptor (ITIC-Th) based on indacenodithieno[3,2-b]thiophene core and thienyl side-chains for organic solar cells (OSCs). Relative to its counterpart with phenyl side-chains (ITIC), ITIC-Th shows lower energy levels (ITIC-Th: HOMO = -5.66 eV, LUMO = -3.

Correction: Low bandgap semiconducting polymers for polymeric photovoltaics.

Correction for 'Low bandgap semiconducting polymers for polymeric photovoltaics' by Chang Liu et al., Chem. Soc.

High-Performance Solution-Processed Non-Fullerene Organic Solar Cells Based on Selenophene-Containing Perylene Bisimide Acceptor.

Non-fullerene acceptors have recently attracted tremendous interest because of their potential as alternatives to fullerene derivatives in bulk heterojunction organic solar cells. However, the power conversion efficiencies (PCEs) have lagged far behind those of the polymer/fullerene system, mainly because of the low fill factor (FF) and photocurrent. Here we report a novel perylene bisimide (PBI) acceptor, SdiPBI-Se, in which selenium atoms were introduced into the perylene core.

Flexible Organic Transistors with Controlled Nanomorphology.

We report the controlled nanomorphology of semiconducting polymers on chemically and mechanically stable nanogrooved polymer substrates. By employing silicon dioxide thin films with finely adjusted thicknesses on nanogrooved polymer substrates, semiconducting polymer thin films oriented and aligned along the nanogrooves were obtained. Organic field-effect transistors (OFETs) fabricated from the oriented semiconducting polymer, poly[4-(4,4-dihexadecyl-4H-cyclopenta[1,2-b:5,4-b']dithiophen-2-yl)-alt-[1,2,5]thiadiazolo-[3,4-c]pyridine] (PCDTPT), yielded saturation hole mobilities as high as 19.

High mobility emissive organic semiconductor.

The integration of high charge carrier mobility and high luminescence in an organic semiconductor is challenging. However, there is need of such materials for organic light-emitting transistors and organic electrically pumped lasers. Here we show a novel organic semiconductor, 2,6-diphenylanthracene (DPA), which exhibits not only high emission with single crystal absolute florescence quantum yield of 41.

Doping-Induced Carrier Density Modulation in Polymer Field-Effect Transistors.

Controlled device parameters of high-mobility polymer field-effect transistors (FETs) are demonstrated by modest doping and charge compensation. Through fleeting chemical vapor treatments of aligned poly[4-(4,4-dihexadecyl-4H-cyclopenta[1,2-b:5,4-b']dithiophen-2-yl)-alt-[1,2,5]thiadiazolo-[3,4-c]pyridine] (PCDTPT) thin films as the charge transport layer in the FET channel, the FET properties are tailored by controlling doping concentration of the PCDTPT adjacent to metal electrodes.

Low bandgap semiconducting polymers for polymeric photovoltaics.

In order to develop high performance polymer solar cells (PSCs), full exploitation of the sun-irradiation from ultraviolet (UV) to near infrared (NIR) is one of the key factors to ensure high photocurrents and thus high efficiency. In this review, five of the effective design rules for approaching LBG semiconducting polymers with high molar absorptivity, suitable energy levels, high charge carrier mobility and high solubility in organic solvents are overviewed. These design stratagems include fused heterocycles for facilitating π-electron flowing along the polymer backbone, groups/atoms bridging adjacent rings for maintaining a high planarity, introduction of electron-withdrawing units for lowering the bandgap (Eg), donor-acceptor (D-A) copolymerization for narrowing Eg and 2-dimensional conjugation for broadened absorption and enhanced hole mobility.

Ultrasensitive solution-processed broad-band photodetectors using CH₃NH₃PbI₃ perovskite hybrids and PbS quantum dots as light harvesters.

Sensing from ultraviolet-visible to infrared is critical for both scientific and industrial applications. In this work, we demonstrate solution-processed ultrasensitive broad-band photodetectors (PDs) utilizing organolead halide perovskite materials (CH3NH3PbI3) and PbS quantum dots (QDs) as light harvesters. Through passivating the structural defects on the surface of PbS QDs with diminutive molecular-scaled CH3NH3PbI3, both trap states in the bandgap of PbS QDs for charge carrier recombination and the leakage currents occurring at the defect sites are significantly reduced.

Measurement of the Charge Carrier Mobility Distribution in Bulk Heterojunction Solar Cells.

Charge carrier transport through organic solar cells is fundamentally dispersive due to the disordered structure and complex film morphology within the photoactive layer. A novel application of transient photocurrent and short-circuit variable time-delayed collection field measurements is used to reconstruct the complete charge carrier mobility distribution for the photogenerated carriers in optimized organic solar cells.

Polymer-Polymer Förster Resonance Energy Transfer Significantly Boosts the Power Conversion Efficiency of Bulk-Heterojunction Solar Cells.

Optically resonant donor polymers can exploit a wider range of the solar spectrum effectively without a complicated tandem design in an organic solar cell. Ultrafast Förster resonance energy transfer (FRET) in a polymer-polymer system that significantly improves the power conversion efficiency in bulk heterojunction polymer solar cells from 6.8% to 8.

Conjugated polyelectrolyte hole transport layer for inverted-type perovskite solar cells.

Unlabelled: Organic-inorganic hybrid perovskite materials offer the potential for realization of low-cost and flexible next-generation solar cells fabricated by low-temperature solution processing. Although efficiencies of perovskite solar cells have dramatically improved up to 19% within the past 5 years, there is still considerable room for further improvement in device efficiency and stability through development of novel materials and device architectures. Here we demonstrate that inverted-type perovskite solar cells with pH-neutral and low-temperature solution-processable conjugated polyelectrolyte as the hole transport layer (instead of acidic

Pedot: PSS) exhibit a device efficiency of over 12% and improved device stability in air.

Ultrafast charge transfer in operating bulk heterojunction solar cells.

The ultrafast charge generation process in organic solar cell devices is investigated by transient reflection spectroscopy on five state-of-the-art bulk heterojunction systems. The charge generation process in operating devices is found to be a combination of an ultrafast generation mechanism over several hundred femto-seconds and a slow process from pico-seconds to nanoseconds, limited by exciton diffusion dynamics. In addition, the lack of electric field dependence in the charge dynamics rules out geminate recombination as an important loss mechanism.

Polymer homo-tandem solar cells with best efficiency of 11.3%.

Rational materials design and interface engineering are both essential to realize a high performance for tandem cells. Two identical bulk heterojunctions are connected in series using novel interconnection layers combining pH-neutral conjugated polyelectrolytes and a thin film of ZnO nanoparticles by a solution process. The best performing tandem cells achieve a power conversion efficiency of 11.

An organic surface modifier to produce a high work function transparent electrode for high performance polymer solar cells.

Modification of an ITO electrode with small-molecule organic surface modifier, 4-chloro-benzoic acid (CBA), via a simple spin-coating method produces a high-work-function electrode with high transparency and a hydrophobic surface. As an alternative to PEDOT:PSS, CBA modification achieves efficiency enhancement up to 8.5%, which is attributed to enhanced light absorption within the active layer and smooth hole transport from the active layer to the anode.

Solution-processed pH-neutral conjugated polyelectrolyte improves interfacial contact in organic solar cells.

The intrinsic acidic nature of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) hole-transporting layer (HTL) induces interfacial protonation and limits the device performance in organic solar cells based on basic pyridylthiadiazole units. By utilizing a pH neutral, water/alcohol soluble conjugated polyelectrolyte CPE-K as the HTL in p-DTS(PTTh2)2:PC71BM solar cells, a 60% enhancement in PCE has been obtained with an increased V(bi), reduced R(s), and improved charge extraction. These effects originate from the elimination of interfacial protonation and energy barrier compared with the PEDOT:PSS HTL.

Tandem solar cells made from amorphous silicon and polymer bulk heterojunction sub-cells.

A tandem solar cell based on a combination of an amorphous silicon (a-Si) and polymer solar cell (PSC) is demonstrated. As these tandem devices can be readily fabricated by low-cost methods, they require only a minor increase in the total manufacturing cost. Therefore, a combination of a-Si and PSC provides a compelling solution to reduce the cost of electricity produced by photovoltaics.

High thermal stability solution-processable narrow-band gap molecular semiconductors.

A series of narrow-band gap conjugated molecules with specific fluorine substitution patterns has been synthesized in order to study the effect of fluorination on bulk thermal stability. As the number of fluorine substituents on the backbone increase, one finds more thermally robust bulk structures both under inert and ambient conditions as well as an increase in phase transition temperatures in the solid state. When integrated into field-effect transistor devices, the molecule with the highest degree of fluorination shows a hole mobility of 0.

The influence of binary processing additives on the performance of polymer solar cells.

In this study, we report the investigation of the influence of binary processing additives, 1,8-octanedithiol (ODT) and 1-chloronaphthalene (CN) on the performance of polymer solar cells (PSCs). It was found that the power conversion efficiency (PCE) can be enhanced to 8.55% from the PSCs processed with binary processing additives as compared with ∼6.

Mapping orientational order in a bulk heterojunction solar cell with polarization-dependent photoconductive atomic force microscopy.

New methods connecting molecular structure, self-organization, and optoelectronic performance are important for understanding the current generation of organic photovoltaic (OPV) materials. In high power conversion efficiency (PCE) OPVs, light-harvesting small-molecules or polymers are typically blended with fullerene derivatives and deposited in thin films, forming a bulk heterojunction (BHJ), a self-assembled three-dimensional nanostructure of electron donors and acceptors that separates and transports charges. Recent data suggest micrometer-scale orientational order of donor domains exists within this complex nanomorphology, but the link to the optoelectronic properties is yet unexplored.

A stable polyaniline-benzoquinone-hydroquinone supercapacitor.

A Polyaniline-Supercapacitor with quinone electrolytes remains stable over 50 000 galvanostatic charge-discharge cycles. The quinones provide superior stability by preventing the conversion of porous polyaniline to a highly reactive state. Our work shows that highly stable polymer-supercapacitors can be engineered by combining electrochemically active polymers and redox-active electrolytes with concerted electrochemical properties.